Page 1
Colour Television 21D3 Service Manual Model CE21D3-C (W.Europe) Service Ref. No. CE21D3-C-01 PRODUCT CODE: 111327015 ORIGINAL VERSION: Chassis No. EB4-A Specifications Power source AC 220~240V 50Hz Television system System B/G Colour system Receiving channel VHF: E2-E12 Note CATV: X, Y, Z, S1-S41...
SAFETY PRECAUTION 1: An isolation transformer should be connected in the 3: When replacing a chassis in the cabinet, always be power line between the receiver and the AC line when certain that all the protective devices are installed a service is performed on the primary of the converter properly, such as, control knobs, adjustment covers or transformer of the set.
CIRCUIT DESCRIPTION 1. POWER SUPPLY control) The chroma signal is divided into R-Y and B-Y The power supply circuit of the EB4-A chassis is chroma signals, demodulated in IC201, and output from composed of a rectifier smoothing circuit, an oscillation pin30 (R-Y) and pin31 (B-Y).
6. HORIZONTAL OUTPUT Pin25: Black A horizontal oscillation signal is output from pin37 of Pin26: IREF IC201 and switches the drive transistor Q431. This Pin27: Odd/Even output switching signal is current amplified by the drive Pin28: GND transformer T431 and drives the output transistor Q432. Pin29: - When Q432 becomes ON, an amplifying current flows Pin30: V-deflection stop output...
SERVICE CONTROL ADJUSTMENT B1 POWER SUPPLY ADJ. AFT ADJ. TU-AGC ADJ. MAIN BOARD HIGH VOLTAGE & H-WIDTH ADJ. FOCUS ADJ. V-CENTRE ADJ. V-SIZE ADJ. H-CENTRE ADJ. GREY SCALE ADJ. SIF BOARD SIF ADJ. CRT BOARD IC3811 IC3801 K38H2 K38H1 AUDIO BOARD IC1251 IC3451 IC3401...
Page 7
B1 POWER SUPPLY ADJUSTMENT HIGH VOLTAGE & WIDTH ADJUSTMENT 1. Set VR641 to be mechanically centre before [HIGH VOLTAGE ADJUSTMENT] pressing the mains ON/OFF switch. 1. Tune the receiver to the circular pattern. 2. Tune the receiver to a PAL circular pattern. 2.
CIRCUIT ALIGNMENT 10kΩ 0.002µF 75Ω 1kΩ Output probe Input probe VIF alignment SETTING Adjustment Waveform DC 15.5V C644 + By using T141, adjust "P" to AGC voltage (4.3-4.5V) IC201-pin48 be maximum amplitude. Output probe IC201-pin45 (Side b) Input probe IC201-pin7 Marker frequency 38.9MHz Sweep ATT...
Page 9
INITIALISATION (Important Notice) When you replace a memory IC (IC802), it is 2. Select the desired service item by using the Function necessary to initialise the IC as following step. button on the remote control handset. 3. Change the data by using the Level + or - button A.
CABINET PARTS LIST FOR MODELS CE21D3-C -01 Note: Parts order must contain Service Ref. No., Part No., and descriptions. Item Part No. Description CABINET PARTS 610 268 0478 ASSY,CABINET FR-F3JA 610 261 6057 BUTTON POWER-F3SCM 610 264 8003 CABINET BACK-F3JLV...
Part No. Description Part No. Description Ref. No. Chassis construction Read description in the Capacitor and Resistor as follows: CAPACITOR CE21D3-C-01 CERAMIC 100P K 50V Rated Voltage Tolerance Symbols: ASSY,PWB,MAIN F3JTV 1AA0B10H02900 (Page 11) Less than 10PF ASSY,PWB,SIF 3D-A2 ST 1AA0B10H0270A (Page 16) A: Not specified B: ±0.1PF...
I suddetti componenti devono essere specified on the part service manual colour bar and controls adjusted 7. Le forme di onda furono prese con il seg- CE21D3-C-01 sostituti esclusivamente con quelli indi- SERVICE REF.NO. be used for components replacement for normal picture. Waveforms nale di barre colore e i controlli regolati cati nell'elenco.
Page 22
Main Board /Pannello Principal Circuit side/Lato del Circuito CRT Board /Pannello Cinescopio 3D surround Board /Pannello 3D surround Circuit side/Lato del Circuito Circuit side/Lato del Circuito Audio Board /Pannello Audio SIF Board /Pannello SIF Circuit side/Lato del Circuito Circuit side/Lato del Circuito C3842 K38H2 Q3802...