Troubleshooting - VECOPLAN VAZ 800 XL SP Operation Manual

Operation
Pos: 101 .1 / 08_BE/0 2_1_St öru ngsa bhilfe /Ü3_Stö run gsa bhilfe @ 10\ mo d12 40_2 .doc @ 1 2964 5
8.6.1

Troubleshooting

Pos: 101 .2 / 08_BE/0 2_1_St öru ngsa bhilfe /ÜT_A nzeich en Ur sach e Ma ßn ahm en @ 10\ mo d124 1_2 .doc @ 12 967 1
Symptom
Pos: 101 .3 / 08_BE/0 2_1_St öru ngsa bhilfe /Mas chine hat star ke Vibr ation en @ 6\ mod3 863 _2. doc @ 129 879
The machine has strong
vibrations
Pos: 101 .4 / 08_BE/0 2_1_St öru ngsa bhilfe /Mo torw ellenza pfe n ver bog en @ 6\ mod3 864 _2. doc @ 129 905
Motor shaft journal bent
Pos: 101 .5 / 08_BE/0 2_1_St öru ngsa bhilfe /Keilrie mensc heib e bes chädi gt @ 6\m od3 286 _2.d oc @ 129 827
Pulley damaged.
Pos: 101 .6 / 07_BE/0 2_1_St öru ngsa bhilfe /Alte_ Modul e/L age rtem per atu ren zu h och @ 6\ mod3 287 _2. doc @ 129 853
Bearing temperatures too high
> 80°C
Pos: 101 .7 / 07_BE/0 2_1_St öru ngsa bhilfe /ZK/Abn or male Ger äusch e im Ze rklein ere r @ 6 \mo d49 62_ 2.do c @ 1 538 77
Abnormal noise in the
shredder
Pos: 101 .8 / 07_BE/0 2_1_St öru ngsa bhilfe /ZK/ Zu g ro ßes En dkor n Z erklei ner ungsw erkz eug @ 17 \mo d75 34_ 2.doc @ 1 541 63
Chip size too large
Pos: 101 .9 / 07_BE/0 2_1_St öru ngsa bhilfe /ZK/Ro tor blockie rt @ 6\m od3 295 _2.d oc @ 153 617
Rotor blocked
Pos: 101 .10 /07_BE/ 02_1 _Stör ungs abhilf e/ZK/H äufig es Rev ersie ren Hau ptant rieb es Zerkl einer ung s @ 1 7\m od7 535 _2.d oc @ 154 189
Main drive reverses too often
Pos: 101 .11 /07_BE/ 02_1 _Stör ungs abhilf e/ZK/Sc hiebe r h ebt sic h @ 5 \mo d10 98_ 2.do c @ 1 533 05
ram lifts up in front position
Pos: 101 .12 /07_BE/ 02_1 _Stör ungs abhilf e/ZK/ Mat erial s etzt sic h un ter Sc hieb er @ 5\m od1 103 _2.d oc @ 153 383
material under the ram
Pos: 101 .13 /07_BE/ 02_1 _Stör ungs abhilf e/ZK/Sc hiebe r bl eibt in E ndlag e Dr ucksch alter pr üfen @ 6\ mod 329 0_2 .doc @ 15 369 5
Ram remains in one end
position, does not change
direction
Pos: 101 .14 /Seitenw echsel @ 1 0\m od10 80_ 2.d oc @ 7 681 3
48
Cause
The machine is tilted
Damage in transit or installation
error
Damage in transit or installation
error.
Lubrication insufficient or over-
filled with grease
Contamination
Installation error of the bearing
Foreign body near the rotor
Diameter of screen holes too
big
Gap between reducing tool and
counter knife too big
(wear of reducing tools)
Foreign bodies in rotor area
Reducing tools are worn
Counter knife is worn
guide rails worn
seal at the front of ram is worn
Setting of pressure switch
incorrect
Pressure switch defective
Slots of guide rails are dirty
Action
Align machine with spirit level
Replace motor
Replace pulley
Check lubrication
Renew seals,
wash bearing, re-grease
Check bearing assembly
Stop machine immediately,
clean out complete reducing area and
remove foreign bodies
Replace screen for smaller screen size
Turn or replace reducing tool
Replace counter knife
Stop reducer,
clear up working space and remove
foreign bodies
Turn or replace reducing tools
Replace counter knife
replace guide rails,
clean out complete reducing area
replace plastic seal element
Check setting of pressure switch
Replace pressure switch
Clean slots of guide rails