Page 1
Ver. 1 INTEGRATED NETWORK AV RECEIVER Click here! AVR-X3300W On-line service parts list We are getting ready. On-line owner’s manual (Release schedule) http://manuals.denon.com/AVRX3300W/NA/EN/index.php http://manuals.denon.com/AVRX3300W/EU/EN/index.php (June 2016) http://manuals.denon.com/AVRX3300W/AP/ZH/index.php (June 2016) CAUTION IN SERVICING ELECTRICAL MECHANICAL REPAIR INFORMATION UPDATING • For purposes of improvement, specifications and design are subject to change without notice. • Please use this service manual with referring to the operating instructions without fail. • Some illustrations using in this service manual are slightly different from the actual set.
Page 2
CAUTION IN SERVICING SAFETY PRECAUTIONS NOTE FOR SCHEMATIC DIAGRAM NOTE FOR PARTS LIST INSTRUCTIONS FOR HANDLING SEMICONDUCTORS AND OPTICAL UNIT CAUTION IN SERVICING. Initializing This Unit JIG FOR SERVICING...
Page 3
SAFETY PRECAUTIONS ◎ Make a safety check after servicing! The following items should be checked for continued protection of the customer and the service Check that all screws, parts and wires removed or disconnected when servicing have been put back technician.
Page 4
NOTE FOR SCHEMATIC DIAGRAM WARNING: Parts indicated by the z mark have critical characteristics. Use ONLY replacement parts recommended by the manufacturer. CAUTION: Before returning the set to the customer, be sure to carry out either (1) a leakage current check or (2) a line to chassis resistance check.
Page 5
CAUTION IN SERVICING. Initializing This Unit Make sure to initialize this unit after replacing the microcomputer or any peripheral equipment, or the digital PCB. 1. Press the power button to turn off the power. 2. While holding down buttons "ZONE2 SOURCE" and "DIMMER" simultaneously, press the power but- ton to turn on the power.
Page 6
ELECTRICAL SCHEMATIC DIAGRAMS PRINTED CIRCUIT BOARDS SCH01_DIR_APLD HDMI, F HDMI SCH02_VIDEO PLD INPUT, VIDEO, FRONT CNT SCH03_NET PHY SCH04_MAIN DAC MAIN, RS CNT, GUIDE L SCH05_HDMI TX FRONT, CNT, RS232, FUNCTION, FRONT HDMI CABLE, TOP GUIDE SCH06_HDMI SW2 SIDE CNT, SMPS SCH07_HDMI SW1 SCH08_DSP LEVEL DIAGRAM...
Page 7
SCHEMATIC DIAGRAMS SCH01_DIR_APLD DIR/A.PLD TO 0A TO 1A TO 2A TO C9 DIR input DIR output FROM FROM HDMI SW2 NET PHY HDMI TX CH1: DATA CH1:D-DATA *FILTER COMPONENTS VALUE TYPE TOLERANCE Ω Ω R1907 METAL FILM OR CARBON ≤ 5% CH2: fs 0.068UF FILM OR CERAMIC (CH OR C0G)
Page 9
SCH03_NET PHY NET PHY TO 4B TO CPU DM920_SPDIF NET/USB_MCK NET/USB_LRCK DIR/A.PLD NET/USB_BCK TO 5B NET/USB_DATA_/FR NET/USB_DATAF/FL FROM NET3.3V NET2.5V D.SUPPLY NET1.8V NET1.25V TO A0 DGND R1207 OPEN R1208 OPEN C1172 OPEN-1608 920PCK C1173 100N-K 920VD0 C1174 1N-K 920VD1 U1005 MFI337S3959 920VD2 920VD3...
Page 10
SCH04_MAIN DAC TO A7 TO A3 TO 6B TO A8 MAIN DAC FROM FROM FROM FROM DIR/A.PLD DIR/A.PLD DIR/A.PLD DA+5V A/DIN_R DAGND A/DIN_L DAGND 100N-K-1608 R1997 DACRTNGND R1998 100N-K-1608 DA+5V C2137 R1999 DAGND OPEN-1608 100-1608 DAGND R2002 TO DIGITAL CNT 100-1608 C2143 10U-K-2012...
Page 17
SCH11_CPU TO 9D TO B4 HDMI RX TO CPU LEVEL CHG TO 0E TO D6 TO ADV8003 TO D.SUPPLY NET PHY ADV7850 TO 8D DSP1FLAG3 C1356 OPEN DSP1CLK CEC_COM CEC_COM DSP1MISO H5VDET R1488 DSP1MOSI Q1043 HINSELC DSP1RST 2SD2114K HINSELB R1393 OPEN R1490 DSP1CS...
Page 18
SCH12_CPU LEVEL CHG CPU LEVEL CHG TO DIGITAL CNT TO D3 SWM3.3V FROM M3.3V D.SUPPLY DGND TO D7 SWM3.3V DGND TO CPU TO E0 GND LINE POWER+ LINE POWER- LINE ANALOG AUDIO DIGITAL AUDIO TMDS SIGNAL ANALOG VIDEO DIGITAL VIDEO STBY POWER...
Page 35
PRINTED CIRCUIT BOARDS HDMI, F HDMI Lead-free Solder When soldering, use the Lead-free Solder (Sn-Ag-Cu). HDMI (A SIDE) F HDMI (A SIDE) F HDMI (B SIDE) FRONT FFC C1681 HDMI PCB [MP] 7020-08008-020-0S 470UF/16V-KR3 C1320 C1319 C1317 N1017 N1000 C1313 C1314 C1316 L1058...
Page 36
INPUT, VIDEO, FRONT CNT INPUT (A SIDE) INPUT (B SIDE) FRONT CNT (A SIDE) FRONT CNT (B SIDE) R4223 C4226 R4341 R4227 R4221 R4222 R4298 R4253 C4234 R4251 R4252 R4243 R4314 R4264 R4265 NC(HDAM_GND) R4266 NC(HDAM_GND) C4253 H/P_L R4330 R4287 R4288 H/P_GND H/P_R...
Page 39
FRONT, CNT, RS232, FUNCTION, FRONT HDMI CABLE, TOP GUIDE FRONT (A SIDE) FRONT (B SIDE) CNT (A SIDE) CNT (B SIDE) CNT B'D(MP_2) CNT B'D(MP_2) 7020-07963-000-1S 7020-07963-000-1S C4442 C4441 CP4402 CP4403 C4478 C4477 M3.3V D/MGND SWM3.3V A+7V A-7V MICGND V.AUX/GND H/PGND H/PL H/PR...
Page 40
SIDE CNT, SMPS SIDE CNT (A SIDE) SIDE CNT (B SIDE) SMPS (A SIDE) SMPS (B SIDE) TU_GPIO2/TUNED TU_GPIO2/TUNED TU_RST/ST TU_RST/ST BKT4141 BKT4140 TU_SEN TU_SEN C4140 C4141 TU_SDIO/SDA TU_SDIO/SDA TU_SCLK/SCL 470PF/250V 470PF/250V TU_SCLK/SCL TU_GND TU_GND TUNER_R TUNER_R TU_GND BKT4000 TU_GND TUNER_L B/PIRIN_DE TUNER_L...
Page 41
LEVEL DIAGRAM FRONT ch AVR-X3300W LEVEL DIAGRAM FRONT ch NJU72750 NJU72343 ANALOG H/POUT SPEAKER LINE IN + GAIN + PCM1690 + PCM9211 + PREOUT - - NJU72343 to ZONE2 +30dB NJU72343 MAX. OUTPUT 4.2Vrms Differential Out SP OUT PCM1690 4.23Vrms/8Ω 0dBFS MAX SIGNAL LEVEL 0dBFS = +/-4.0Vpp=2.83Vrms...
Page 42
CENTER ch AVR-X3300W LEVEL DIAGRAM CENTER ch NJU72343 SPEAKER + GAIN PCM1690 + + PREOUT - - +30dB NJU72343 MAX. OUTPUT 4.2Vrms Differential Out SP OUT PCM1690 4.23Vrms/8Ω 0dBFS MAX SIGNAL LEVEL 0dBFS = +/-4.0Vpp=2.83Vrms +20dB DOLBY LIMIT LEVEL (ALLch-3dBFS) +29dB 0dBFS=1.06Vrms...
Page 44
SURROUND ch AVR-X3300W LEVEL DIAGRAM SURROUND ch NJU72343 SPEAKER + GAIN PCM1690 + + PREOUT - - +30dB NJU72343 MAX. OUTPUT 4.2Vrms Differential Out SP OUT PCM1690 4.23Vrms/8Ω 0dBFS MAX SIGNAL LEVEL 0dBFS = +/-4.0Vpp=2.83Vrms +20dB DOLBY LIMIT LEVEL (ALLch-3dBFS) +29dB 0dBFS=1.06Vrms...
Page 45
SURR.BACK ch AVR-X3300W LEVEL DIAGRAM SURR.BCK ch NJU72343 SPEAKER + GAIN PCM1690 + + PREOUT - - +30dB NJU72343 MAX. OUTPUT 4.2Vrms Differential Out SP OUT PCM1690 4.23Vrms/8Ω 0dBFS MAX SIGNAL LEVEL 0dBFS = +/-4.0Vpp=2.83Vrms +20dB DOLBY LIMIT LEVEL (ALLch-3dBFS) +29dB 0dBFS=1.06Vrms...
Page 46
ZONE2 AVR-X3300W LEVEL DIAGRAM ZONE2 NJU72750 NJU72343 from To MAIN DA SB-ch SPEAKER LINE IN + ZONE GAIN NJU72343 NJW1194 NJU72750 TONE ZONE2 MONO MONO GAIN MONO PCM5100 +30dB NJU72343 MAX. OUTPUT 4.2Vrms SP OUT 4.23Vrms/8Ω PCM5100 0dBFS = 2.0Vrms MAX SIGNAL LEVEL...
Page 50
POWER DIAGRAM AVR-X3300 VCC DIAGRAM MAIN +B S1(AMP +B) MAIN -B +3.3V ( PCM5100*2 ) AP7361-ADJ DA+5.0V ( PCM1690 / PCM9211 ) KIA7805API KIA7808API A+7.0V A-7.0V KIA7908PI S2(+8V,-8V) TRIGGER +12V PQ120DNA A.V+5.0V KIA7805API JUMPER TUNER_+5V RELAY MAIN TRANS KIA7905PI A.V-5.0V FL AC (F1) FL AC (F2) M3.3V (CPU / R1EX24128BSASO1 / MC14094BDTR2G*5 )
Page 51
WIRING DIAGRAM AVR_X3300 WIRE DIAGRAM WIFI_ANT AC CORD WIFI_BT_ANT HDMI PCB CY920 2P TAP (SMPS) MODULE SPK PCB 23P CARD CABLE 40P CARD CABLE FRONT CNT PCB VIDEO PCB MAIN TRANS INPUT PCB 13P WIRE (AUDIO IN) 7P TAP (FL) 8P TAP (A/V) D10SB60 VIDEO...
Page 52
SEMICONDUCTORS Only major semiconductors are shown, general semiconductors etc. are omitted to list. The semiconductor which described a detailed drawing in a schematic diagram are omitted to list. 1. IC's R5F564MJCDFC (HDMI : U1018) Pin Name Symbol Pu/Pd STBY STOP Function STBY Smoothing capacitor connection pin...
Page 53
Pin Name Symbol Pu/Pd STBY STOP Function Pin Name Symbol Pu/Pd STBY STOP Function STBY STBY USB0_DP USB0_DP NC(open) JTAG TCK/ JTAG I/F for PLD writing/Audio PLD (5M80ZT100C5N) APLD CLK/ VSS_USB VSS_USB Ground pin control pin/DAC (PCM1690) control pin DAC CLK AVCC_USBA AVCC_USBA Power supply pin...
Page 54
AD8195 AD8195ACPZ (INPUT : U1022) Pin Name Symbol Pu/Pd STBY STOP Function STBY PIN CONFIGURATION AND FUNCTION DESCRIPTIONS DIR RST DIR (PCM9211) control pin PD5/IRQ5/AN113 787_HAINT HDMI Rx (MN864787) audio interrupt signal det PD4/IRQ4/AN112 ZVOL STB ZONE2 volume control pin (NJW1194) DE_RST Video decoder (ADV7850) reset control pin 30 AVCC...
Page 55
PCM9211 www.ti.com SBAS495 – JUNE 2010 PIN CONFIGURATIONS PCM9211 (HDMI : U1040) PT PACKAGE LQFP-48 DESCRIPTION (TOP VIEW) NAME TOLERANT 24 MDI/SDA Software control I/F, SPI data input / I2C data input/output(2) ERROR/INT0 VDDRX 25 MC/SCL Software control I/F, SPI clock input / I2C clock input(2) NPCM/INT1 RXIN1 MPIO_A0...
Page 58
PCM1690 (HDMI : U1048) W9864G6KH-5 Block diagram CLOCK BUFFER CONTROL SIGNAL GENER ATOR COMMAND DECODER COLUMN DECODER COLUMN DECODER CELL ARRAY CELL ARRAY BANK #0 BANK #1 MODE REGIST ER SENSE AMPLIFIER SENSE AMPLIFIER ADDRESS BUFFER DATA CONTROL CIRCUIT BUFFER COLUMN PCM1690 Pin Function REFRESH...
Page 59
PCM1690 SBAS448A – OCTOBER 2008 – REVISED JANUARY 2009.............................. www.ti.com FUNCTIONAL BLOCK DIAGRAM PCM1690 FUNCTIONAL BLOCK DIAGRAM TERMINAL PULL- DESCRIPTION DOWN TOLERANT NAME Control port mode selection. Tied to VDD: SPI, left VOUT1+ DIN1 MODE DIN2 open: H/W mode, tied to DGND: I2C VOUT1- DIN3 Audio Interface...
Page 60
PCM5100, PCM5101, PCM5102 SLAS764 – MAY 2011 www.ti.com DEVICE INFORMATION TERMINAL FUNCTIONS, PCM510x PCM5100 (HDMI : U1052, U1053) NJU72343 (INPUT : IC4202, IC4203) PCM510X (top view) Pin Function No. Symbol Function No. Symbol Function AREF Analog reference potential terminal DATA IC control data input Address selection terminal CLOCK...
Page 61
G Crosstalk -65dBtyp. WIDE BAND 3-INPUT 1-OUTPUT 3-CIRCUIT VIDEO AMPLIFIER G Internal 6dB Amplifier G Internal 75Ω Driver G Bipolar Technology G Package Outline DIP16,DMP16 GENERAL DESCRIPTION PACKAGE OUTLINE 2. FL DISPLAY The NJM2586A is a wide band 3-input 1-output 3-circuit video I PIN CONFIGURATION and BLOCK DIAGRAM amplifier.
Page 62
MECHANICAL DISASSEMBLY Flowchart 1. COVER 2. FRONT PANEL ASSY 3. RADIATOR ASSY 4. HDMI PCB 5. VIDEO PCB 6. INPUT PCB 7. MAIN PCB 8. SMPS PCB 9. TRANS EXPLODED VIEW PACKING VIEW...
Page 63
DISASSEMBLY Flowchart • Remove each part following the flow below. • Reassemble the removed parts in the reverse order. • Read "SAFETY PRECAUTIONS" before reassembling the removed parts. • If wire bundles are removed or moved during adjustment or part replacement, reshape the wires after completing the work. Failure to shape the wires correctly may cause problems such as noise. •...
Page 64
• The photographs with no shooting direction indicated were taken from the top of the unit. (1) Remove the screws. Remove the HOLDER. Remove the TAPE. • Photos of AVR-X3300W E3 are used in this manual. The viewpoint of each photograph...
Page 65
3. RADIATOR ASSY 4. HDMI PCB Proceeding : TOP COVER → COVER → FRONT PANEL ASSY → RADIATOR ASSY Proceeding : TOP COVER → COVER → HDMI PCB (1) Remove the screws. (1) Remove the screws. Shooting direction: A Shooting direction: C View from the bottom Shooting direction: D (2) Remove the screws.
Page 66
5. VIDEO PCB 7. MAIN PCB Proceeding : TOP COVER → COVER → HDMI PCB → VIDEO PCB Proceeding : TOP COVER → COVER → HDMI PCB → VIDEO PCB → INPUT PCB → MAIN PCB (1) Remove the connector. (1) Remove the screws.
Page 68
PACKING VIEW *MANUAL POLYBAG ASSY* *MIC STAND ASSY POLYBAG CODE : 6337-04006-201-0S POLYBAG CODE : 6337-21071-900-0V ZIPPERBAG(A5size) ZIPPERBAG(A4size) Notes on RADIO (ALL) SPOTIFY insertion sheet Cautions on Using Batteries (E2 only) dts : User update insertion SAFETY INST. (ALL) Update insertion sheet (E3 only) WARRANTY USA &...
Page 69
REPAIR INFORMATION TROUBLE SHOOTING SPECIAL MODE 1. POWER Special mode setting button 2. Analog video 1. Version Display Mode 3. HDMI/DVI 2. PANEL / REMOTE LOCK Selection Mode 4. AUDIO 3-1. Selecting the Mode for Service-related 5. Network / Bluetooth / USB 3-2.
Page 70
TROUBLE SHOOTING 1. POWER 1.1. The unit does not power on 1.2. Fuse is blown The unit does not power on Blown fuse Does the power indicator on the front panel Does the power indicator on the front Check the rectifier diode in the Check for short circuits between flash in green or white when the power is turned panel flash in red when the power is turned...
Page 71
2. Analog video CVBS / COMPONENT / HDMI OUT NG Input CVBS / COMPONENT Input CVBS Input COMPONENT Input Function : CBL / SAT Function : CBL / SAT HDMI Check the input signal to the VIDEO DECODER. Can a signal be confirmed at the following To "A"...
Page 72
Input Input CVBS COMPONENT Check the settings of each IC. Check the settings of each IC. Are the following voltages set? Are the following voltages set? HDMI PCB HDMI PCB faulty. HDMI PCB HDMI PCB faulty. N1039 - 10 pin : Hi (3.3 V) N1039 - 9 pin : Lo (0 V)
Page 73
3. HDMI/DVI 3.1. No picture or sound is output (HDMI to HDMI) (8) When using a DENON Blu-ray/DVD player, is the "HDMI" indicator of the fluorescent display lit? Proceed to YES when using a Blu-ray/DVD player produced by other manufactures.
Page 74
(15) Are a picture and sound output when a dif- The TV is faulty. ferent TV is used? Check the unit. "HDMI "Rx/Tx" Failure Detection"...
Page 75
4. AUDIO 4.1. AUDIO CHECK No audio output CHECK 1 INPUT SURROUND MODE SOURCE Check the ANALOG AUDIO BLOCK Audio output OK? ANALOG 2CH DIRECT ANALOG CHECK 2 INPUT SURROUND MODE SOURCE Check the DIGITAL AUDIO BLOCK Legacy Audio output OK? COAX or OPT (PCM or DolbyDigital or dts…) CHECK 3...
Page 76
4.2. Power AMP (AMP PCB) 4.3. Analog audio No audio output. No audio output. Protection is activated. Is the power transistor open or short circuited? Is a voltage of ± 8 V supplied to INPUT PCB Replace the power transistor. Repair the ±...
Page 77
5. Network / Bluetooth / USB 5.1. Cannot connect to the network Check the connection environment Can the D3.3V2 output volt- The circuit of D5V_POWER Insert the LAN cable correctly and then turn on Is D5V_POWER (U1018 uCOM Is the LAN cable correctly inserted? age (3.3 V) to U1067 (DC-DC between U1018 and U1067 the power again.
Page 78
5.2. Cannot establish a Bluetooth connection Can the NET2.5V output volt- The circuit of E_POWER2 be- Is E_POWER2 (U1018 uCOM age (2.5 V) to U1072 (DC-DC tween U1018 and U1072 are 133 pin) "Hi" ? Check the Bluetooth device being used Conv.) be confirmed? faulty.
Page 79
5.3. Cannot recognize the connected USB device 5.4. No picture or sound is output Check the USB device being used Checking the unit (If no picture is output) Are digital video signals(920PCK, 920VD0 - The circuit around CY920, U1011 (V.PLD) is Is a USB hub being used? Do not use a USB hub.
Page 80
HDMI test point USB test point FRONT FFC C1681 HDMI PCB [MP] 7020-08008-020-0S 470UF/16V-KR3 C1320 C1319 C1317 N1017 C1313 C1314 C1316 N1000 L1058 N1017 N1020 C1686 CN4402 Q1079 Q1080 470UF/16V-KR3 C1655 N1033 N1039 Q1049 R1338 R1364 C1872 N1036 R1354 N1019 R1355 R1366 R1365...
Page 81
6. SMPS Operation waveform for each part DC 5V is not output. Primary drain After primary side rectification (Caution: High voltage, electric shock) (Caution: High voltage, electric shock) D4143 1N4007 OPTION OPTION D4142 1N4007 Replace the IC4144 C4148 0.01UF/250V R4148 Is IC4144 (TOP268EG) dam- After secondary rectifications (TOP268EG) and D4142 /...
Page 82
HDMI "Rx/Tx" Failure Detection 1. Prior checking Check item (0) : Checking the HDMI connector Checking the condition of the HDMI pin (rear/front). There are deformed pins. Replace the HDMI connector. Check for deformed pins. None of the pins are deformed. 3.
Page 83
Port: Select COM port of PC Baud rate: 19200bps Data bits: 8 Stop bits: 1 Parity: none Transmitted text Flow control: none Figure 1-1 Device Connection Method (AVR-X3300W) Select Append CR-LF Forwad: (none) Check the Local Echo check box. Figure 3 Serial Port Setup Screen...
Page 84
After exiting "Setup Assistant,” execute the above. 1. Input a command in the 2.Click on the transmission button. transmission command input. Press Figure 6-1. AVR settings (AVR-X3300W) Figure 8 Method for Sending Termite Commands All the for Volume 7 segment indicator Lights...
Page 85
3. Starting detecting the point of failure 3-1 Check the "HDMI/DVI" item in troubleshooting. Check item(5). : Does a video signal come from HDMI OUT to Check item(1). Is the GUI version readable correctly? TV correctly? Check that the version of the AVR can be read Go to check item (60) correctly.
Page 86
3-2 Switcher1 failure detection procedure Checking device. (HDMI Switcher1) When the results of check item (7) are "the communication results are not OK" Check communication between CPU and the HDMI Switcher1 device. Checking device. (HDMI Switcher1) Check item (7). Check communication between CPU and the HDMI Example : Check the power supply voltage.
Page 87
Checking the reset waveform. (HDMI Switcher1) Check item(10). Checking the reset waveform : Check the waveform. Check the HDMI Tx. Is the "RESET" waveform of the TP near the HDMI Switcher1 Check the HDMI Switcher1 Check the HDMI Switcher2 Remove the damping resistor (U1003) correct (like the one shown in the diagram) when the Remove the damping resistor Remove the damping resistor...
Page 88
When the results of check item (7) are "the communication results are OK" Check item(14). Checking the DDC status register : Example ZONE2 OUT HDMI IN Send the following command from Termite.exe. Case of IN5 Send the command "i 002B 0084 0001".
Page 89
When the results of check item (13) are "NO" When the results of check item (14) are "00 or 04" (Detection of 5V is not OK) (Detection of DDC is not OK.) Check the +5V voltage. (HDMI IN5 - 7) Check the DDC line.
Page 90
When the results of check item (14) are "22 or 11" (Detection of DDC is OK.) Checking the TMDS status register (HDMI Switcher1) 3.3V TMDS Signal TMDS Check item(17). Checking register of the TMDS CLK detection status Example register : Send the following command from Termite.exe.
Page 91
When the results of check item (19) are "33 or 23 or 13 or 03" Example (Detection of HPD is OK / Detection of RXSENSE is OK ) Checking the EDID register. (HDMI ZONE2 OUT) Check item(20). Check the Monitor EDID : ①...
Page 92
When the results of check item (19) are "31 or 21 or 11 or 01" When the results of check item (19) are "32 or 22 or 12 or 02" (Detection of HPD is OK / Detection of RXSENSE is not OK ) (Detection of HPD is not OK / Detection of RXSENSE is OK ) Check the TMDS.
Page 93
When the results of check item (19) are "30 or 20 or 10 or 00" (Detection of HPD is not OK / Detection of RXSENSE is not OK ) Check the TMDS/HPD. (HDMI ZONE2 OUT) Check item(25). Checking the HPD and RXSENSE. : Does the test point near HDMI output connector (N1030) indicate (3.3V)? Does the test point (HPD) near HDMI output connector (N1030)
Page 94
3-3 Switcher2 failure detection procedure Checking device. (HDMI Switcher2) When the results of check item (26) are "the communication results are not OK" Check communication between CPU and the HDMI Switcher2 device. Checking device. (HDMI Switcher2) Check item (26). Check communication between CPU and the HDMI Example : Check the power supply voltage.
Page 95
Checking the reset waveform. (HDMI Switcher2) Check item(29). Checking the reset waveform : Check the waveform. Is the "RESET" waveform of the TP near the HDMI Switcher2 (U1000) correct (like the one shown in the diagram) when the power is turned on? Examples of confirmation waveform RESET U1000...
Page 96
When the results of check item (26) are "the communication results are OK" Check item(31). Checking the DDC status register : Example ZONE2 OUT HDMI IN Send the following command from Termite.exe. Case of IN1 Send the command "i 0053 00B4 0001".
Page 97
When the results of check item (30) are "NO" When the results of check item (31) are "00 or 04" (Detection of 5V is not OK) (Detection of DDC is not OK.) Check the +5V voltage. (HDMI IN1 - 4) Check the DDC line.
Page 98
When the results of check item (31) are "22 or 11" (Detection of DDC is OK.) Check item (35). Checking the TMDS input waveform. : Checking the TMDS status register (HDMI Switcher2) Check the TMDS waveform at the following test point. 3.3V Is the waveform like the sample? TMDS Signal...
Page 99
3-4 Tx failure detection procedure Checking device. (HDMI Tx) Example : Check communication between CPU and the HDMI Tx device. Check item (38). Check communication between CPU and the HDMI Tx device. i 0000 0000 0001 Send the following command from Termite.exe. Send the command "i 0000 0000 0001".
Page 100
When the results of check item (38) are "the communication results are not OK" Check item(41). Checking the reset waveform : When the power is turned on, is the "RESET" waveform correct (as shown in the figure)? Checking device. (HDMI Tx) The test points are as follows.
Page 101
When the results of check item (38) are "the communication results are OK" HDMI OUT HDMI IN Checking the HPD/RXSENSE status register. (HDMI OUT) Example Check item(43). Check the HPD and RXSENSE register value of the HDMI TX device. Turn Video Conversion "OFF" on the setup menu. Send the following command from Termite.exe.
Page 102
Example When the results of check item (43) are "30" (Detection of HPD is OK / Detection of RXSENSE is OK ) Checking the EDID register. (HDMI OUT) Check item(45). Check the Monitor EDID : ① Unplug the AC cord. Plug the AC cord into a power outlet. The first eight bytes are nor- ②...
Page 103
When the results of check item (43) are "10" When the results of check item (43) are "20" (Detection of HPD is OK / Detection of RXSENSE is not OK ) (Detection of HPD is not OK / Detection of RXSENSE is OK ) Check the TMDS.
Page 104
When the results of check item (43) are "00" (Detection of HPD is not OK / Detection of RXSENSE is not OK ) Check the TMDS/HPD. (HDMI OUT) Check item(50). Checking the HPD and RXSENSE. : Does the test point near HDMI output connector (N1031) indicate (3.3V)? Does the test point (HPD) near HDMI output connector (N1031) indicate "Hi(3-5V)"?
Page 105
3-5 Front HDMI Buffer (AD8195) failure detection procedure Checking operation between the HDMI (Front HDMI Buffer) and the player Checking the +5V/DDC status register (Front HDMI Buffer) Check item(53). Checking the 5V status register : Example Send the following command from Termite.exe. b In order to check, connect the player to the HDMI terminal and configure the player as AVR source.
Page 106
When the results of check item (53) are "78 or 70" When the results of check item (54) are "00 or 04" (Detection of 5V is not OK.) (Detection of DDC is not OK.) Check the +5V voltage. (Front HDMI Buffer) Check the DDC Line.
Page 107
When the results of check item (54) are "22" (Detection of DDC is OK) Checking the TMDS status register (Front HDMI Buffer) Check item(57). Check the TMDS CLK detection status of the regis- Check item (58). Checking the TMDS input waveform. : Example ter.
Page 108
3-6 GUI (ADV8003) failure detection procedure Check item(60). When the results of check item (61) are "the communication results are not OK" Rewrite to the GUI ROM. Go to check item (3) After writing, is the GUI version readable cor- rectly? Checking device.
Page 109
Checking the reset waveform. Check the I2C communication line. Check item(66). Checking the reset : Check item(67). Check the I2C communication line : Check the CPU. Check the CPU. 10ms Is the waveform of the TP near the GUI (U1026) correct (like the one Is the waveform of the TP near the GUI(U1026) correct (like the one shown in the diagram) when the power is turned on? shown in the diagram) when the power is turned on?
Page 110
3-7 GUI and PLD failure detection procedure Check item(69). Does a video signal come from HDMI OUT to TV correctly? : Check item(71). Check the PLD video signal line from the GUI : HDMI OUT Check the video signal waveform at the following test point. Is the waveform like the sample? 3.3V Turn Video Conversion "ON"...
Page 111
When the results of check item (69) are "YES" (When the menu display is OK) Check item(73). Check the HDMI Tx video signal line from the HDMI Tx : HDMI HDMI OUT Check the video signal waveform at the following test point. Is the waveform like the sample? 3.3V Turn Video Conversion "ON"...
Page 113
CLOCK FLOW & WAVE FORM IN DIGITAL BLOCK WAVE FORM ③ DIR input CH0ASD0 RXI2S0/DSD1 CH0ASD1 RXI2S1/DSD2 U1001 RXI2S2/DSD3 CH0ASD2 MN864787 CH0ASD3 RXI2S3/DSD4 HDMI Tx RXLRCK/DSD5 CH0ALRCLK CH0ABCLK RXBCK/DSDSCK SCKI DACMCK CH0AMCLK RXMCK/DSDMCK DACBCK RXSPDIF/DSD0 CH0ASPDIF DACLRCK LRCK CH1:DIRO1 U1041 U1048 5M240ZT100C5N PCM1690...
Page 114
(E3 and E2 model only) (See 3-5. TUNER STEP mode (E3 / E2 only)) If there are multiple DENON AV receivers in the same area, this mode prevents other AV receivers from being operated concur- 3-6 Remote ID Setup Mode ↑ ↑...
Page 115
Mode Button A Button B Button C Descriptions Mode used when this unit cannot be recovered. TUNER 11 Forced USB All Device Write Mode Forcibly switches this unit to USB update mode. PRESET CH STATUS (See 2.9. Forced USB All Device Write Mode) TUNER ZONE2...
Page 116
→ Q3 Network MAC ADDRESS information → Q4 Bluetooth MAC Address information Q1 Ethernet 2nd Boot Loader, Rhapsody Flag : q Model destination information : Ethernet SBL AVR-X3300W \\\ Press "STATUS" button. \ : Region (E3, E2, E1C, JP) w Serial Number : B************-0A S/N.
Page 117
1.4. Error display See the table below for descriptions of the displayed errors and countermeasures for these. If multiple errors occur, only one item is displayed. The priority order is w, e, r, t, y, q. Condition States Display TROUBLE SHOOTING FIRM ERROR The model name, brand name and region information written in the firmware are compared to the region...
Page 118
1.5. Version Display in the Setup Menu Follow the steps below to display the firmware information. (1) Press the "SETUP" button on the remote control. (2) Select "General - Information - Firmware". The version information is displayed as a 12-digit number as shown in the screenshot below. General/Firmware Version XXXX - XXXX - XXXX...
Page 119
2. PANEL / REMOTE LOCK Selection Mode 2.1. Actions Switch the PANEL LOCK and REMOTE LOCK modes between on and off. 2.2. Starting up While holding down buttons "TUNER PRESET CH+" and "ZONE2 SOURCE" simultaneously, press the power button to turn on the power. Select the desired mode using the "TUNER PRESET CH+"...
Page 120
3-1. Selecting the Mode for Service-related 3-1.1. Actions Select diagnostic mode (service path check mode), protection history display mode, or 232C standby 4.OP INFO clear mode. Operation Info for the unit can be checked. 3-1.2. Starting up 2. While holding down buttons "ZONE2 SOURCE", "DIMMER" and "STATUS" simultaneously, press the power button to turn on the power.
Page 121
3-2. Protection History Display Mode 3-2.1. Actions (c) DC (if the last protection is DC) This mode enables the unit to record and display the event when the THERMAL, ASO or DC protection is PRT:DC activated. Cause : DC output of the power amplifier is abnormal. If protections have been activated multiple times, the latest protection operation is recorded.
Page 122
3-3. 232C Standby Clear Mode 3-2.4. Clearing the Protection History 3-3.1. Actions There are two ways to clear the protection history. Switches from 232C standby mode to normal standby mode. 3-3.2. Starting up (a) Activate Protection History Display Mode. Press the "STATUS" button to display the protection his- tory.
Page 123
3-4. Operation Info Mode 3-4.1. Actions (e) Thermal Protection (E/F) count This mode enables the unit to display the accumulated operating time, power On count and each pro- THM E:___/F:___ tection count. "STATUS" 3-4.2. Starting up 2. While holding down buttons "ZONE2 SOURCE", "DIMMER" and "STATUS" simultaneously, press the (f) Current Protection count power button to turn on the power.
Page 124
3-6.1. Actions This is a special mode for enabling reception STEP of the ANALOG TUNER to be changed. This function allows only the desired AV receiver to be operated if multiple DENON AV receivers are used in the same room.
Page 125
4. Protection Pass Mode 6. CY920 Initialization Mode 4.1. Actions 6.1. Actions • This mode allows the power to be turned on without activating protections. The following items are initialized. • This mode functions in the same way as normal power-on, except that protections are not activated. (1) Favorites (2) Quick Select 4.2.
Page 126
7. Clearing the Operation Info 7.1. Actions • Displays the accumulated operating time of the unit, the number of times the power was switched on, and the number of occurrences of each protection. 7.2. Operations Remove all input/output terminals and the AC plug. Connect the AC plug again and place the product in standby mode.
Page 127
DIAGNOSTIC MODE Service Path Check Mode 1.1. Actions This function is convenient for confirming problem paths in the product and checking the paths after repairing. The Video and Audio paths can be checked. The backup data is not rewritten. 1.2. Starting up 2.
Page 128
Paths to be confirmed Display Settings What to confirm Input Source : CBL/SAT ・ HDMI input ⇒ Speaker output (Front L/R) Input Mode : HDMI (fixed) ( b The input source can be switched to any source except CBL/SAT.) fig.04a Sound mode : STEREO 4 HDMI A05:HDMI...
Page 129
Paths to be confirmed Display Settings What to confirm Input Source : CBL/SAT ・ HDMI input (MAIN function) ⇒ HDMI output (MAIN) HDMI pass Video Conversion (IP Scaler) : Off ( b The input source can be switched to any source except CBL/SAT.) fig.11 V03:HDMI PASS (MAIN ZONE)
Page 153
JIG FOR SERVICING Use the following jigs (extension cable kit) when repairing the PCBs. Order with your dealer for the jigs your dealer if necessary. CN5000 CAUTION : Incorrect connections may cause malfunction. Connection of Jig for HDMI PCB ---Items to Be Prepared--- 8U-110084S : EXTENSION UNIT KIT 1Set 8U-110136S : EXTENSION UNIT KIT...
Page 154
(4) Connect the expansion cables. FRONT CNT HDMI SIDE CNT VIDEO INPUT Board-to-Board Connections Ref. No. Ref. No. 7pin CP1022 SIDE CNT N1022 HDMI 27pin CP1016 SIDE CNT N1016 HDMI 21pin CP1018 SIDE CNT N1018 HDMI 9pin CP1020 FRONT CNT N1020 HDMI 23pin...
Page 155
ADJUSTMENT Adjusting Idling Current 1. Preparation (1) Prepare a DC voltmeter. (2) Place the unit under normal usage conditions, away from highly ventilated areas such as next to an air conditioning machine or electric fan. The set requires an ambient temperature of 15℃ to 30℃ and standard humidity. AMP UNIT (3) Settings of This Unit DC Voltmeter...
Page 156
UPDATING PROCEDURE AFTER REPLACING THE PCB. PROCEDURE AFTER REPLACING THE U-COM, ETC. FIRMWARE UPDATE PROCEDURE 1. Items necessary for update 2. Updating via USB 3. Updating via DPMS...
Page 157
PROCEDURE AFTER REPLACING THE PCB. PROCEDURE AFTER REPLACING THE U-COM, ETC. The procedure after replacing the printed circuit boards is as follows. The procedure after replacing the u-COM (microprocessor), flash ROM, etc. is as follows. (1) Change the resistor for setting the region. Procedure PCB Name Ref.
Page 158
FIRMWARE UPDATE PROCEDURE 1. Items necessary for update Items necessary for update are as follows. Offered / not Offered Update Type Needed Part for Update Requirement Standard Service Equipment Purchase from D&M Article code Download from SDI Not offered by D&M Via USB USB Stick (USB 2.0 : Min 1GB) Formatting FAT 32...
Page 159
2. Updating via USB The latest firmware can be downloaded to a USB memory for updates. 2.1. Connecting to the USB Memory (1) Preparation • Use a memory that supports USB2.0. • USB format : Prepare a USB memory formatted in FAT16 or FAT32. •...
Page 160
2.3. File structure on USB Memory 2.5. Start the update. Copy the update files to the USB memory with the following structure. While holding down buttons "TUNER PRESET CH +" and "STATUS" simultaneously, press the power button to turn on the power. USB memory root Model Name Model Area...
Page 161
2.9. Forced USB All Device Write Mode 2.10. Update Procedure in the Event of a CY920 Error 2.9.1. Actions 1.10.1. Actions Perform the following update procedure if "CY920 Error" appears in the display when the power is Mode used when this unit cannot be recovered. Forcibly switches this unit to USB update mode.
Page 162
2.11. About the error codes Error USB Update Error Details of Error code Remedies Code Display See the table below for error codes and details of faults when the firmware is updated through USB memory. Update Error**09 Time Out while obtaining Unplug and reconnect the AC plug, and The error code is displayed as four digits made up of the Device ID below together with **YY ( ** : De- Firmware information.
Page 163
Error USB Update Error Error USB Update Error Details of Error code Remedies Details of Error code Remedies Code Display Code Display Failed to obtain the entire Reinsert or try a new USB device, Un- Try a new USB device, Unplug and Firmware information after Update Error**50 Unable to detect USB.
Page 164
Error USB Update Error Error USB Update Error Details of Error code Remedies Details of Error code Remedies Code Display Code Display Unplug and reconnect the AC plug, and Reinsert or try a new USB device, Un- NACK received in response or try again.
Page 165
3. Updating via DPMS Download the latest firmware from our website and update the firmware. 3.1. Network Connection (1) System Requirements • Internet Connection by Broadband Circuit • Modem • Router • Ethernet cable (CAT-5 or greater is recommended) (2) Setting Internet Computer Modem...
Page 166
3.3. About the error codes Error DPMS Update Error Details of Error code Remedies Code Display See the following table for details on the error code display, details of the error code, remedies when updating the firmware via DPMS. (DPMS : D&M Product Management Server) Error(NG) notification received Check the network connection, Unplug The error code is displayed as four digits made up of the Device ID below together with **YY ( ** : De-...
Page 167
Error DPMS Update Error Error DPMS Update Error Details of Error code Remedies Details of Error code Remedies Code Display Code Display Check the network connection, Unplug Error notification received Check the network connection, Unplug Update Error**24 DPMS connection failure and reconnect the AC plug, and try while requesting the Firm- and reconnect the AC plug, and try...
Page 168
Error DPMS Update Error Error DPMS Update Error Details of Error code Remedies Details of Error code Remedies Code Display Code Display Failed to start up Sub in Unplug and reconnect the AC plug, and Update Error**A7 Time Out while obtaining Unplug and reconnect the AC plug, and Power On sequence during Update Error**62...
Page 169
Copyright 2016 D&M Holdings Inc. All rights reserved.
Page 170
MAIN MAIN PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. Part indicated by "@" mark is not illustrated in the exploded view ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions NOTE:The symbols in the column Remarks indicate the following destinations.
Page 171
D040010086060S C4089 C,ELECT GE 85C 1UF-M/100V,5*11-5RE.SMS SY D040010086060S OTHER PARTS GROUP BD4000 COIL,BEAD CB03YTYN121-1608REEL D340160891210S BKT4143 BRACKET AVRX2200WBKE3(DENON) SECC t1.0+Sn plating /PCB MT 4010214876000SV CLP4002 CLAMP HMX9800(ON)(HAITAI) (W=2.6,L=50)/WIRE(SOLDER) 4330000120000S CN4211 CN,WIRE ASSY 300MM/3P YMH025-03R=YBNH250-03 UL2651#22 SJ L028301030130S CN4212 CN,WIRE 160MM/10P 20010HS-10=YBNH200-10 UL2651#26 SJ...
Page 172
FRONT FRONT PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. Part indicated by "@" mark is not illustrated in the exploded view ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions NOTE:The symbols in the column Remarks indicate the following destinations.
Page 176
INPUT INPUT PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. Part indicated by "@" mark is not illustrated in the exploded view ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions NOTE:The symbols in the column Remarks indicate the following destinations.
Page 177
INPUT REF No. Part No. Part Name Remarks Q'ty New Ver R4251 R,CHIP THICK 470-J,1/16W-1608REEL C20004716M160S R4252 R,CHIP THICK 470-J,1/16W-1608REEL C20004716M160S R4253 R,CHIP THICK 220-J,1/16W-1608REEL C20002216M160S R4255 R,CHIP THICK 15K-F,1/16W-1608REEL C20001534M161S R4256 R,CHIP THICK 820-J,1/16W-1608REEL C20008216M160S R4257 R,CHIP THICK 100-J,1/16W-1608REEL C20001016M160S R4258 R,CHIP THICK 91K-J,1/16W-1608REEL...
Page 178
INPUT REF No. Part No. Part Name Remarks Q'ty New Ver R4388 R,CHIP THICK 10K-J,1/16W-1608REEL C20001036M160S R4389 R,CHIP THICK 470K-J,1/16W-1608REEL C20004746M160S R4390 R,CHIP THICK 11K-F,1/16W-1608REEL C20001134M160S R4391 R,CHIP THICK 820-J,1/16W-1608REEL C20008216M160S R4393 R,CHIP THICK 100K-J,1/16W-1608REEL C20001046M160S R4394 R,CHIP THICK 100K-J,1/16W-1608REEL C20001046M160S R4396 R,CHIP THICK 10K-J,1/16W-1608REEL...
Page 179
INPUT REF No. Part No. Part Name Remarks Q'ty New Ver R4514 R,CHIP THICK 47-J,1/16W-1608REEL C20004706M160S R4515 R,CHIP THICK 470K-J,1/16W-1608REEL C20004746M160S R4517 R,CHIP THICK 47-J,1/16W-1608REEL C20004706M160S R4518 R,CHIP THICK 470K-J,1/16W-1608REEL C20004746M160S R4520 R,CHIP THICK 47-J,1/16W-1608REEL C20004706M160S R4521 R,CHIP THICK 470K-J,1/16W-1608REEL C20004746M160S R4523 R,CHIP THICK 47-J,1/16W-1608REEL...
Page 180
INPUT REF No. Part No. Part Name Remarks Q'ty New Ver C4293 C,ELECT GE 85C 47UF-M/25V,5*11 KR3-025V470MC110-T/A5.0S KOSHIN D040470084550S C4294 C,ELECT GE 85C 10UF-M/50V,5*11-5RE.SMS SY D040100087070S C4295 C,CERAMIC CHIP T.C COG330PF-J/50V-1608REEL D010331167160S C4296 C,CERAMIC CHIP T.C CH)330PF-J/50V-1608REEL GRM1882C1H331JA01D D010331167165S C4297 C,CERAMIC CHIP T.C CH)330PF-J/50V-1608REEL GRM1882C1H331JA01D D010331167165S C4298...
Page 183
AMP PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. Part indicated by "@" mark is not illustrated in the exploded view ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions NOTE:The symbols in the column Remarks indicate the following destinations.
Page 184
REF No. Part No. Part Name Remarks Q'ty New Ver R422 R,CARBON FILM 470-J,1/5W-52RE-AX C00004716P520S R423 R,CHIP THICK 10K-J,1/16W-1608REEL C20001036M160S R424 R,FIXED,M.O. RSD-R1-2WJ-0.47 3.5*8.6 P=5MM SMALL R.REEL N113136647820S 00D9630345903 R425 00D9630345903 R,FIXED,M.O. RSD-R1-2WJ-0.47 3.5*8.6 P=5MM SMALL R.REEL N113136647820S R426 R,CHIP THICK 5.6K-J,1/16W-1608REEL C20005626M160S R427 R,CARBON FILM 1.2K-J,1/5W-52RE-AX...
Page 185
REF No. Part No. Part Name Remarks Q'ty New Ver R552 R,CARBON FILM 470-J,1/5W-52RE-AX C00004716P520S R553 R,CHIP THICK 10K-J,1/16W-1608REEL C20001036M160S R554 R,FIXED,M.O. RSD-R1-2WJ-0.47 3.5*8.6 P=5MM SMALL R.REEL N113136647820S 00D9630345903 R555 00D9630345903 R,FIXED,M.O. RSD-R1-2WJ-0.47 3.5*8.6 P=5MM SMALL R.REEL N113136647820S R556 R,CHIP THICK 5.6K-J,1/16W-1608REEL C20005626M160S R557 R,CARBON FILM 1.2K-J,1/5W-52RE-AX...
Page 186
REF No. Part No. Part Name Remarks Q'ty New Ver R683 R,FIXED,M.O. RSD-R1-2WJ-0.47 3.5*8.6 P=5MM SMALL R.REEL N113136647820S 00D9630345903 R684 00D9630345903 R,FIXED,M.O. RSD-R1-2WJ-0.47 3.5*8.6 P=5MM SMALL R.REEL N113136647820S R685 R,CHIP THICK 5.6K-J,1/16W-1608REEL C20005626M160S R686 R,CARBON FILM 1.2K-J,1/5W-52RE-AX C00001226P520S R687 CN,WIRE 1P JUMPER (0.6/52MM) L045084006040S R688 R,CARBON FILM 33K-J,1/5W-52RE-AX...
Page 187
REF No. Part No. Part Name Remarks Q'ty New Ver C504 C,ELECT GE 85C 47UF-M/50V,8*11.5-5RE ROB-50V470MG3#9-T2 D040470087140S 00D2544583971 C505 963133502480S C,FILM POLYESTER ST-0.00047UF-J/100V-5RE HPE471J2AP050T DAEHUNG D02047106C250S C506 C,ELECT GE 85C 470UF-M/16V,8*11.5 KR3-016V471MF115-T/A5.0S KOSHIN D040471083550S 963133502020S C507 963133502480S C,FILM POLYESTER ST-0.00047UF-J/100V-5RE HPE471J2AP050T DAEHUNG D02047106C250S C508 C,FILM POLYESTER ST-0.00047UF-J/100V-5RE HPE471J2AP050T DAEHUNG...
Page 188
D040100087070S C4005 C,ELECT GE 85C 10UF-M/50V,5*11-5RE.SMS SY D040100087070S C4006 C,ELECT GE 85C 10UF-M/50V,5*11-5RE.SMS SY D040100087070S OTHER PARTS GROUP BKT4000 BRACKET AVRX2200WBKE3(DENON)BURRING HOLE SPCC t0.8+SN A4/S 401021019610DS CLP4000 CLAMP HMX9800(ON)(HAITAI) (W=2.6,L=50)/WIRE(SOLDER) 4330000120000S CLP4001 CLAMP HMX9800(ON)(HAITAI) (W=2.6,L=50)/WIRE(SOLDER) 4330000120000S CLP4002 CLAMP HMX9800(ON)(HAITAI) (W=2.6,L=50)/WIRE(SOLDER)
Need help?
Do you have a question about the AVR-X3300W and is the answer not in the manual?
Questions and answers