EyeClick BEAM Installation Manual
Hide thumbs
Also See for BEAM:
- Quick start manual (16 pages) ,
- Installation manual (23 pages) ,
- User manual (68 pages)
Advertisement
Quick Links
Advertisement
Related Manuals for EyeClick BEAM
Summary of Contents for EyeClick BEAM
- Page 1 INSTALLATION GUIDE TABLE...
-
Page 2: What's In The Box
WHAT’S IN THE BOX Thank you for purchasing your new BEAM. Here's what's included: The BEAM system Power cord The BEAM keyboard Remote controller for operating the system menus for controlling the BEAM projector... -
Page 3: Before Installing
BEFORE INSTALLING Before starting the installation and setup, please make sure that: Full batteries are equipped in both the The yellow saftey ribbon is pulled out The keyboard's toggle on the is on and keyboard and remote controller. of the batteries compartment. its green background is visible. - Page 4 BEFORE INSTALLING In order to hang your BEAM from the ceiling, please prepare: 4 TURNBUCKLES 4 CONCRETE EYE BOLT 4 CHAINS 4 CARABINER CLIPS HOOK/EYE ANCHORS See chart on slide 6 to determin required length Note Please prepare a measuring tool, a marker, a drill, a pair of pliers and a leveler for the installation process itself.
-
Page 5: Technical Specifications
TECHNICAL SPECIFICATIONS LEFT The BEAM device dimentions and measurments in milimeters: BACK... - Page 6 RECTANGULAR TABLE SETUP Use this table to determine if the PROJECTION SURFACE MINIMUM ZOOM MAXIMUM ZOOM installation location can accomodate the desired projection size. Distance from surface to device Width Height Width Height All measurments are in centimeters. Note Mounting the device more than 425 centimiters above the projection surface may produce false interactions and sensor inaccuracies.
- Page 7 ROUND TABLE SETUP Use this table to determine if the PROJECTION SURFACE MINIMUM ZOOM MAXIMUM ZOOM installation location can accomodate the desired projection size. Distance from surface to device Projection Diameter Projection Diameter All measurments are in centimeters. Note Mounting the device more than 425 centimiters above the projection surface may produce false interactions and sensor inaccuracies.
- Page 8 INSTALLING BEAM Unpack the device and place it face Attach each of the carabiner clips to the four ear loops on the top panel. Each end of the turnbuckles should down on a soft surface such as a carpet. be screwed to it's middle to allow for Next, connect the turnbuckles to the carabiner clips.
- Page 9 INSTALLING BEAM Locate the center of the projection area - the device will be installed directly In order to leave sufficient space for the projection area, keep a distance of at least above it. Measure a square on the ceiling above the center of the projection area.
- Page 10 INSTALLING BEAM Drill holes at of the square's marked corners. Make sure the drilled holes depth and Fasten the bolts in place. diamater match the measurments of your eye bolt anchors. Insert an eye bolt anchor to each one of the drilled holes.
- Page 11 INSTALLING BEAM Mount the device by attaching one end of each chain to each of the hook bolt Place the leveler on the device and anchors, and the other end to the turnbuckles connected to the device's top panel. adjust the turnbuckles until the device is...
- Page 12 INSTALLING BEAM Connect the device to a 15A 110-240V Connect the device to your router using Turn on the projector using the remote Once the projector is fully activated, use dedicated, stable power outlet. The an Ethernet cable. The internet port is controller.
- Page 13 DROP (FALSE) CEILING INSTALLATION To install BEAM in a location with a drop (false) ceiling, Make sure the device's weight is fully supported by the anchor the device to the true ceiling or a support beam chains attached to the true ceiling or a support beam - as previously explained.
- Page 14 INSTALLING BEAM Alternatively, you can use a pole for an open ceiling installation. Simply connect If you're installing the device to a metal the pole to the device's top panel. ceiling, use suitable hook bolt anchors for metal surfaces. TOP PANEL POLE MOUNT...
- Page 15 SETTING UP YOUR BEAM If needed, it's possible to slightly adjust If the projection is skewed, straighten it by clicking Set up the projection are so it will cover the table you aim to project the menu button on your projection remote, then on entirly.
- Page 16 SIGN IN & CONFIGURATION If the projection is illegible during the sign in, configuration or any other point, tap the right Note that after resetting the projection, it must be button on the keyboard's trackpad repeatedly until reaching the stanby screen, then type B to adjusted and calibrated (calibration is available in the reset the projection.
- Page 17 Ethernet cable, select the WI-FI button and select and available network to connect to. ENTER CREDENTIALS Note that these are case-sensitive. Username: eyeclick Password: Qwerty!# The device's serial number is listed on the sticker on the back of the keyboard. LOGIN...
- Page 18 Once the device has been updated and is ready, the downloading updates. This step may take up to 20 progress slider will be replaced by a text: "Not in Please read the BEAM QuickStart Guide to learn more minutes. The device might restart automatically during schedule".
- Page 19 SIGN IN & CONFIGURATION While in the control area, please hold the Ctrl key while typing iddqd to access the maintenance section. SET UP TEAMVIEWER Tap the button. A dialog will apear. In it, select Assign. After, tap the right button on the trackpad to return back.
- Page 20 SIGN IN & CONFIGURATION Now let's make sure the motion sensor camera is capturing the projection area correctly. Tilt the camera mirror to move the direction if needed. You can also reduce the projection scale through the zoom wheel on the projector. Note that any change to the projection setup Tap CAMERA PREVIEW in the maintenance section.
- Page 21 SIGN IN & CONFIGURATION Finally, go to the Settings section and set the time zone to the correct one. Note The device will automatically restart itself once a new timezone is set.
- Page 22 FITTING THE PROJECTION TO A TABLE Now let's make sure the projection fits to the table's size and shape. Before starting, please make sure the table is completely clear of any objects or people and that the projection is unobstructed. If needed, go to the Projector section in the control Go to the Settings section in the control area and Select the shape of the table - it can be either round...
- Page 23 FITTING THE PROJECTION TO A TABLE If a rectangular projection mask was selected, fit it the table's size and shape by: DRAG PROJECTION MASK Hold and drag the X icon to move the projection mask to the center of the table. ANCHOR ICONS Hold and drag the + anchor icons to the edge of the table.
- Page 24 FITTING THE PROJECTION TO A TABLE If a rectangular projection mask was selected, fit it the table's size and shape by: DRAG PROJECTION MASK Hold and drag the X icon to move the projection mask to the center of the table. CIRCLE SIZE ICON Hold and drag the + icon to change the size of the projection.
- Page 25 ENJOY YOUR BEAM! Please read the BEAM QuickStart Guide to learn how to manage and operate your device. For any issues or questions, please contact us support.team@eyeclick.com Email: Website: https://support.joinbeam.com/open-support-ticket/...
Need help?
Do you have a question about the BEAM and is the answer not in the manual?
Questions and answers