Advertisement
Keep handles dry, clean and free from oil and grease.
9
DO NOT allow anyone, especially children, to come within a radius of at least five metres around the work area when work is in
8
progress.
Immediately stop the tool in the event of a malfunction of the motor or the ON/OFF button or in case of unusual noise.
9
When not in use, the machine must be stored in a dry, locked place out of the reach of children.
9
Before using the product and after any shock, please check it for signs of wear or damage.
9
Always switch off the machine:
9
every time you leave the device unattended;
before releasing an obstruction;
before checking, cleaning or working on the product;
after hitting a foreign object;
every time the product starts to vibrate abnormally.
Inspect and regularly service the product. Repairs should be carried out only by an authorized service centre or a similar qualified
9
specialist.
When not in use, store the product out of the reach of children.
9
Always carry the tool by the handle, never the drill.
9
DO NOT use the product on a slippery surface.
8
DO NOT use the product on steep, slippery slopes.
8
Be careful when using the machine in stormy weather. DO NOT use the machine during lightning, thunderstorms and bad weather
9
in general.
1.2.
FUEL HANDLING
Allow the machine to cool before performing inspection, adjustments, maintenance, servicing and storage.
9
Be very careful when handling fuels. They are flammable and the vapours are explosive.
9
Use only an approved container.
9
Never remove the fuel cap or add fuel while the machine is on. Turn the unit off and allow the engine and exhaust components to
9
cool before refuelling.
Never refuel inside a room.
9
Never store the tool and the fuel containers indoors where there is a naked flame.
9
If fuel has spilled, DO NOT attempt to start the machine, but rather move it away from the spill before starting to use it. Clean any
9
spills.
Replace and tighten the fuel tank cap after refuelling.
9
Follow the instructions in this manual for both filling the tool with fuel and fuel management during maintenance and storage.
9
1.3.
RESIDUAL RISKS
1.3.1.
Even if you use this product in accordance with all safety requirements, the potential risks of injuries and damage remain. The
following hazards might happen within the structure and design of this product.
There are adverse health consequences due to the emission of vibrations if the product is used over long periods of time
or not managed properly and maintained in a suitable way.
There are risks of injuries and property damage caused by the attachments or broken attachments or sudden impact of
hidden objects when using the cutting function.
Risk of damage to persons and property caused by flying objects.
Prolonged use of this product exposes the operator to vibration and may contribute to the onset of so-called "white finger" disease.
To reduce the risk, please wear gloves and keep your hands warm.
If any of the symptoms of the "white finger" syndrome appear, consult a doctor immediately. Symptoms of the "white finger" include:
numbness, loss of sensitivity, tickling, tingling, pain, loss of strength, colour changes or skin condition. These symptoms usually
appear on fingers, hands or wrists. The risk is higher at low temperatures.
Risk of hearing loss if the machine is used for long periods of time without hearing protection.
2. INTRODUCTION
Drills holes up to 800mm deep and 200mm wide, ideal for seating trees, garden posts and fence supports into the ground. 52cc 2hp Petrol
motor. Three different diameter bore sizes - 100, 150 or 200mm. Twin ergonomic handles for comfort and ease of use (by one or two people).
Auger brake automatically stops the bit from turning if hard underground impediment is hit.
3. SPECIFICATION
MODEL NO: ............................................................ PHA100
Engine Capacity: ............................................................ 52cc
Engine Type: .................. Single Cylinder Air Cooled 2-Stroke
Fuel Consumption: ........................................ 0.85L/h, 850g/h
Fuel Tank: .............................................. 2-Stroke 25:1 (1.2L)
Max Engine Speed: .................................................. 8500rpm
Maximum Power: .............................................. 2hp 7500rpm
Maximum Torque:.......................................................1.85Nm
Noise Rating: ............................. 116dB(A) Guaranteed value
Vibration/Uncertainty ................................20.52m/s
4. OPERATION
4.1.
FILLING THE FUEL TANK
DO NOT attempt to refuel when the engine is hot.
8
DO NOT expose fuel to heat source or naked flames.
8
If fuel is spilt, immediately stop refuelling and DO NOT start the engine. Clean up the spill and fill the machine in another location.
DO NOT fill the fuel tank to the neck of the filler as there is a risk of overflow.
8
DO NOT refuel in a closed and unventilated area.
8
© Jack Sealey Limited
/ 1.5m/s
2
2
Original Language Version
PHA100
Issue 2 (3,4)
17/09/21
Advertisement
