Table of Contents
Advertisement
LOCATION OF USER CONTROL
INFRARED TRANSMITTER WINDOW
POWER
Press → On.
Press again → Off. (Stand-by)
PERSONAL PREFERENCE buttons
• Used to select any of four preset channels.
Cursor buttons
Used to move cursor on menu screen.
VOLUME UP/DOWN
(+) Increases sound.
(–) Decreases sound.
AV MODE
MUTE
Press → Mutes sound.
Press again → Restores sound.
• CLOSED CAPTION appears when sound is muted.
DIRECT ACCESS
Accesses any channel/inputs numbers by the keypad.
button: DTV Decoder only
POP FUNCTION
You can watch two pictures at the same time.
-CH-
:
Used to switch the channel for the
sub-picture of the TWIN PICTURE
screen.
INPUT:
Used to select the source from INPUT
terminals for the sub-picture of the
TWIN PICTURE screen.
TWIN PICTURE:
Splits the screen into two smaller
equally sized screens, when pressed
again, enlarges the left screen, and,
if pressed again, exits the function.
SEARCH:
Press to select the SEARCH
screen mode.
SELECT:
Selects the screen in TWIN
PICTURE and Search screen modes.
FREEZE:
When this button is pressed with
the regular screen, will change to the
TWIN PICTURE screen and the
picture at the time the button was
pressed will become the sub-picture,
displayed as a frozen image.
SWAP:
The left and right screens are
interchanged with the TWIN
PICTURE function.
CM SKIP:
Use this function when you want to
scan other channels during a
commercial break.
LIGHT
When this button is pressed, some buttons on the remote
control unit will light. The lighting will turn off if no
operations are performed within about six seconds. This
button is used for performing operations in dark places.
• The light button on the Remote Control glows in the dark. To use the glow-in-the-dark display on the remote control, place it
under a fluorescent light or other lighting.
Note
• The phosphorescent material contains no radioactive or toxic material, so it is safe to use.
•
The degree of illumination will vary depending on the strength of lighting used.
• The degree of illumination will decrease with time and depending on the temperature.
• The time needed to charge the phosphorescent display will vary depending on the surrounding lighting.
Remote control mode select buttons
Use to switch the remote control unit modes.
• By selecting one of the three mode select buttons,
this remote control can be used to adjust common
functions, such as channel selection, for that device.
POWER
DTV
VCR/
DVD/
STB
TV
CATV
PERSONAL PREFERENCE
A
B
C
D
ENTER
VOL
CH
MENU
AV MODE
MUTE
INPUT
ANT-A/B
DISPLAY
ENT.
FLASHBACK
TWIN
PICTURE
SEARCH Q-SOUND
VIEW
CH
FREEZE
SELECT
MODE
INPUT
SWAP
CM SKIP
TITLE
PLAY FF
REW
CH/SKIP
PAUSE
STOP
REC
VCR/DVD
DDFC
POWER
REAR PROJECTION TV
VCR/DVD CONTROL
DDFC
Used to select High-quality image.
13
61R-WP5H
55R-WP5H
(Continued)
ENTER button
MENU
Press → Accesses MAIN MENU.
Press again → Exits MAIN MENU.
CHANNEL UP/DOWN
(+) Selects the next higher channel.
(–) Selects the next lower channel.
INPUT
Press → Switches to external video
INPUT 1 mode.
Press again → Switches to external video
INPUT 2 mode.
Press 3 times → Switches to external video
INPUT 3 mode.
Press 4 times → Switches to external video
INPUT 4 mode.
Press 5 times → Switches to external video
INPUT 5 mode.
Press 6 times → Switches back to the
original TV mode.
ANT-A/B button
Press to switch between ANTENNA-A and
ANTENNA-B when you wish to watch TV.
DISPLAY
Press → Displays receiving channel for
four seconds.
Press again → Displays remaining time of
SLEEP TIMER and VIEW
TIMER for four seconds.
FLASHBACK
Returns to previously viewed channel.
ENT.
Used in some instances where a Cable
Converter Box requires an "enter"
command after selecting channels, when
using the DIRECT ACCESS button.
Q-SOUND
Controls the surround settings.
VIEW MODE
Select view size.
Advertisement
Table of Contents
