DeWalt DWE4205 Original Instructions Manual
Hide thumbs
Also See for DWE4205:
- Original instructions manual (248 pages) ,
- Manual (25 pages) ,
- Manual (25 pages)
Related Manuals for DeWalt DWE4205
Summary of Contents for DeWalt DWE4205
- Page 1 All manuals and user guides at all-guides.com DWE4202 DWE4203 DWE4204 DWE4205 DWE4206 DWE4207 DWE4213 DWE4214 DWE4215 DWE4216 DWE4217 Final Page size: A5 (148mm x 210mm)
- Page 2 All manuals and user guides at all-guides.com English (original instructions) Copyright D WALT...
- Page 3 All manuals and user guides at all-guides.com FIGURE 1 DWE4202, DWE4203, DWE4213 DWE4204, DWE4205, DWE4206, DWE4207, DWE4214, DWE4215, DWE4216, DWE4217 FIGURE 2 FIGURE 3...
- Page 4 All manuals and user guides at all-guides.com FIGURE 4 FIGURE 5 A FIGURE 5 B FIGURE 7 FIGURE 6...
-
Page 5: Technical Data
All manuals and user guides at all-guides.com English SMALL ANGLE GRINDERS DWE4202, DWE4203, DWE4204, DWE4205, DWE4206, DWE4207, DWE4213, DWE4214, DWE4215, DWE4216, DWE4217 Congratulations! You have chosen a D WALT tool. Years of experience, thorough product development and innovation make WALT one of the most reliable partners for professional power tool users. -
Page 6: Definitions: Safety Guidelines
All manuals and user guides at all-guides.com English DWE4213 DWE4214 DWE4215 DWE4216 DWE4217 QS/XE QS/XE Voltage Type Power input 1200 1200 1200 1200 1200 No-load/rated speed 11,500 11,000 (QS) 11,000 (QS) 11,000 11,000 11,500 (XE) 11,500 (XE) Wheel diameter Wheel thickness (max) Spindle diameter Spindle length 18.5... -
Page 7: Ec Declaration Of Conformity
(grounded) power tools. Unmodified plugs SMALL ANGLE GRINDERS and matching outlets will reduce risk of DWE4202, DWE4203, DWE4204, DWE4205, DWE4206, electric shock. DWE4207, DWE4213, DWE4214, DWE4215, DWE4216, Avoid body contact with earthed or DWE4217... -
Page 8: Safety Instructions For All Operations
All manuals and user guides at all-guides.com English Prevent unintentional starting. Ensure cutting edges are less likely to bind and are the switch is in the off position before easier to control. connecting to power source and/or Use the power tool, accessories and battery pack, picking up or carrying the tool bits etc., in accordance with these tool. -
Page 9: Causes And Operator Prevention Of Kickback
All manuals and user guides at all-guides.com English abrasive wheel for chips and cracks, backing o) Do not operate the power tool near pad for cracks, tear or excess wear, wire flammable materials. Sparks could ignite brush for loose or cracked wires. If power these materials. -
Page 10: Safety Warnings Specific For Grinding And Abrasive Cutting-Off Operations
All manuals and user guides at all-guides.com English d) Use special care when working corners, twisting or binding of the wheel in the cut and sharp edges etc. Avoid bouncing and the possibility of kickback or wheel breakage. snagging the accessory. Corners, sharp b) Do not position your body in line with and edges or bouncing have a tendency to snag behind the rotating wheel. -
Page 11: Additional Safety Rules For Grinders
E. Threaded locking flange These are: F. Guard – Impairment of hearing. G. Slider switch (DWE4204, DWE4205, DWE4206, DWE4207, DWE4214, DWE4215, DWE4216, – Risk of personal injury due to flying particles. DWE4217) – Risk of burns due to accessories becoming hot H. -
Page 12: Electrical Safety
All manuals and user guides at all-guides.com English • Young children and the infirm. This appliance Follow the fitting instructions supplied with good is not intended for use by young children or quality plugs. Recommended fuse: 13 A. infirm persons without supervision. Using an Extension Cable •... - Page 13 When fitting a disc with a raised centre, make When using the DWE4202, DWE4203, DWE4204, sure that the raised centre (Q) is facing the DWE4205, DWE4206, DWE4207, DWE4213, backing flange (D). DWE4214, DWE4215, DWE4216 or the DWE4217 4. Screw the threaded locking flange (E) onto the grinder for cutting metal or masonry, a Type 1 guard MUST be used.
-
Page 14: Prior To Operation
All manuals and user guides at all-guides.com English 1. Thread the wheel on the spindle by hand. of the rotating accessory and run the power tool at maximum no-load speed for one minute. 2. Depress spindle lock button and use a wrench Damaged accessories will normally break apart on the hub of the wire wheel or brush to tighten during this test time. - Page 15 SLIDER SWITCH (FIG. 3) Grinding rate is greatest when the tool operates (DWE4204, DWE4205, DWE4206, DWE4207, DWE4214, at high speed. DWE4215, DWE4216, DWE4217) 3. Maintain a 20° to 30° angle between the tool WARNING: Before connecting the tool and work surface.
- Page 16 All manuals and user guides at all-guides.com English 3. Maintain a 5° to 10° angle between the tool they bend or twist while the tool is being used to do cut-off work or deep grinding. and work surface for wire cup brushes. To reduce the risk of serious injury, limit 4.
-
Page 17: Cutting Metal
All manuals and user guides at all-guides.com English WARNING: In extreme working PERSONAL SAFETY conditions, conductive dust can 1. No children or pregnant women should enter accumulate inside the machine housing the work area where the paint removal is being when working with metal. - Page 18 All manuals and user guides at all-guides.com English Optional Accessories dry compressed air into the ventilation slots inaccordance with the below WARNING: Since accessories, other maintenance instructions. than those offered by D WALT, have not MAINTENANCE been tested with this product, use of such accessories with this tool could be Your D WALT power tool has been designed...
- Page 19 All manuals and user guides at all-guides.com English Local regulations may provide for separate collection of electrical products from the household, at municipal waste sites or by the retailer when you purchase a new product. WALT provides a facility for the collection and recycling of D WALT products once they have reached the end of their working life.
- Page 20 All manuals and user guides at all-guides.com English GRINDING AND CUTTING ACCESSORY CHART Guard Type Accessory Description How to Fit Grinder Depressed centre grinding disc TYPE 27 Type 27 guard GUARD Flap wheel Backing flange Wire wheels Type 27 depressed centre wheel Threaded clamp nut Wire wheels...
- Page 21 All manuals and user guides at all-guides.com English GRINDING AND CUTTING ACCESSORY CHART (cont.) Guard Type Accessory Description How to Fit Grinder Masonry cutting disc, bonded TYPE 1 Type 1 guard GUARD Metal cutting disc, bonded Backing flange Diamond cutting wheels TYPE 1 Cutting wheel GUARD...
- Page 22 All manuals and user guides at all-guides.com...
- Page 23 All manuals and user guides at all-guides.com...
- Page 24 All manuals and user guides at all-guides.com Belgique et WALT - Belgium BVBA Tel: NL 32 15 47 37 63 www.dewalt.be Luxembourg België Egide Walschaertsstraat 16 Tel: FR 32 15 47 37 64 enduser.BE@SBDinc.com en Luxemburg 2800 Mechelen Fax: 32 15 47 37 99...