DeWalt DWE4202 Manual
Hide thumbs
Also See for DWE4202:
- Original instructions manual (248 pages) ,
- Manual (25 pages) ,
- Original instructions manual (248 pages)
Related Manuals for DeWalt DWE4202
Summary of Contents for DeWalt DWE4202
- Page 1 DWE4202 DWE4203 DWE4204 DWE4205 DWE4206 DWE4207 DWE4213 DWE4214 DWE4215 DWE4216 DWE4217 Final Page size: A5 (148mm x 210mm)
- Page 2 English (original instructions) Copyright D WALT...
- Page 3 FIGURE 1 DWE4202, DWE4203, DWE4213 DWE4204, DWE4205, DWE4206, DWE4207, DWE4214, DWE4215, DWE4216, DWE4217 FIGURE 2 FIGURE 3...
- Page 4 FIGURE 4 FIGURE 5 A FIGURE 5 B FIGURE 7 FIGURE 6...
-
Page 5: Technical Data
English SMALL ANGLE GRINDERS DWE4202, DWE4203, DWE4204, DWE4205, DWE4206, DWE4207, DWE4213, DWE4214, DWE4215, DWE4216, DWE4217 Congratulations! You have chosen a D WALT tool. Years of experience, thorough product development and innovation make WALT one of the most reliable partners for professional power tool users. -
Page 6: Definitions: Safety Guidelines
English DWE4213 DWE4214 DWE4215 DWE4216 DWE4217 QS/XE QS/XE Voltage Type Power input 1200 1200 1200 1200 1200 No-load/rated speed 11,500 11,000 (QS) 11,000 (QS) 11,000 11,000 11,500 (XE) 11,500 (XE) Wheel diameter Wheel thickness (max) Spindle diameter Spindle length 18.5 18.5 18.5 18.5... -
Page 7: Ec Declaration Of Conformity
(grounded) power tools. Unmodified plugs SMALL ANGLE GRINDERS and matching outlets will reduce risk of DWE4202, DWE4203, DWE4204, DWE4205, DWE4206, electric shock. DWE4207, DWE4213, DWE4214, DWE4215, DWE4216, Avoid body contact with earthed or DWE4217... -
Page 8: Additional Specific Safety Rules
English Prevent unintentional starting. Ensure cutting edges are less likely to bind and are the switch is in the off position before easier to control. connecting to power source and/or Use the power tool, accessories and battery pack, picking up or carrying the tool bits etc., in accordance with these tool. -
Page 9: Further Safety Instructions For All Operations
English abrasive wheel for chips and cracks, backing o) Do not operate the power tool near pad for cracks, tear or excess wear, wire flammable materials. Sparks could ignite brush for loose or cracked wires. If power these materials. tool or accessory is dropped, inspect for p) Do not use accessories that require liquid damage or install an undamaged accessory. -
Page 10: Safety Warnings Specific For Sanding Operations
English d) Use special care when working corners, twisting or binding of the wheel in the cut and sharp edges etc. Avoid bouncing and the possibility of kickback or wheel breakage. snagging the accessory. Corners, sharp b) Do not position your body in line with and edges or bouncing have a tendency to snag behind the rotating wheel. -
Page 11: Package Contents
– Risk of personal injury due to flying particles. DWE4207, DWE4214, DWE4215, DWE4216, DWE4217) – Risk of burns due to accessories becoming hot H. Paddle switch (DWE4202, DWE4203, during operation. DWE4213) – Risk of personal injury due to prolonged use. I. Lock-off lever (DWE4202, DWE4203, –... -
Page 12: Electrical Safety
English • Young children and the infirm. This appliance Follow the fitting instructions supplied with good is not intended for use by young children or quality plugs. Recommended fuse: 13 A. infirm persons without supervision. Using an Extension Cable • This product is not intended for use by persons (including children) suffering from diminished If an extension cable is required, use an approved physical, sensory or mental abilities;... - Page 13 CAUTION: Guards must be used with 3. Place the disc (P) on the backing flange (D). this grinder. When fitting a disc with a raised centre, make When using the DWE4202, DWE4203, DWE4204, sure that the raised centre (Q) is facing the DWE4205, DWE4206, DWE4207, DWE4213, backing flange (D).
-
Page 14: Prior To Operation
English 1. Thread the wheel on the spindle by hand. of the rotating accessory and run the power tool at maximum no-load speed for one minute. 2. Depress spindle lock button and use a wrench Damaged accessories will normally break apart on the hub of the wire wheel or brush to tighten during this test time. - Page 15 • Do not use the power tool with a cut- off stand. PADDLE SWITCH (FIG. 1) (DWE4202, DWE4203, DWE4213) • Never use blotters together with 1. To turn the tool on, push the lock-off lever (I) bonded abrasive products.
- Page 16 English they bend or twist while the tool is being 3. Maintain a 5° to 10° angle between the tool used to do cut-off work or deep grinding. and work surface for wire cup brushes. To reduce the risk of serious injury, limit 4.
-
Page 17: Cutting Metal
English WARNING: In extreme working PERSONAL SAFETY conditions, conductive dust can 1. No children or pregnant women should enter accumulate inside the machine housing the work area where the paint removal is being when working with metal. This can result done until all clean up is completed. -
Page 18: Maintenance
English Optional Accessories dry compressed air into the ventilation slots inaccordance with the below WARNING: Since accessories, other maintenance instructions. than those offered by D WALT, have not MAINTENANCE been tested with this product, use of such accessories with this tool could be Your D WALT power tool has been designed hazardous. - Page 19 English Local regulations may provide for separate collection of electrical products from the household, at municipal waste sites or by the retailer when you purchase a new product. WALT provides a facility for the collection and recycling of D WALT products once they have reached the end of their working life.
- Page 20 English GRINDING AND CUTTING ACCESSORY CHART Guard Type Accessory Description How to Fit Grinder Depressed centre grinding disc TYPE 27 Type 27 guard GUARD Flap wheel Backing flange Wire wheels Type 27 depressed centre wheel Threaded clamp nut Wire wheels with threaded Type 27 guard Wire wheel...
- Page 21 English GRINDING AND CUTTING ACCESSORY CHART (cont.) Guard Type Accessory Description How to Fit Grinder Masonry cutting disc, bonded TYPE 1 Type 1 guard GUARD Metal cutting disc, bonded Backing flange Diamond cutting wheels TYPE 1 Cutting wheel GUARD Threaded clamp nut TYPE 27 GUARD...
- Page 24 Belgique et WALT - Belgium BVBA Tel: NL 32 15 47 37 63 www.dewalt.be Luxembourg België Egide Walschaertsstraat 16 Tel: FR 32 15 47 37 64 enduser.BE@SBDinc.com en Luxemburg 2800 Mechelen Fax: 32 15 47 37 99 Danmark WALT Tel: 70 20 15 10 www.dewalt.dk...