Sealey LED180 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMP P OR R TA TANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
TH H E P P RO O DUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PE E RS S ON N AL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
instructions
1. SAFETY
1.1. GENERAL
 It is important to ensure that the light is fully charged before initial use.
 DO NOT turn the light on when it is being charged.
 DO NOT shine directly into your, another person's or an animal's eyes.
 DO NOT allow children to use the light.
DO NOT leave battery in a discharged state. Recharge battery immediately.

Recharge the battery at least once every six months of non-use.
 There are no user serviceable components. DO NOT dismantle.
 DO NOT pull the charger plug from the mains socket by the lead.
1.2. BATTERY SAFETY
 WARNING! To reduce the risk of burns or fi re:
 DO NOT Attempt to open, disassemble, modify or service the battery pack.
 DO NOT Crush, puncture, short external contacts or dispose of in fi re or water.
 DO NOT Expose to temperatures above 40°C (104°F).
 Recycle or dispose of used battery as stipulated by local regulation.
 If the electrolyte in the cells gets on your skin, thoroughly wash with soap and water. If it gets in your eyes, rinse thoroughly with
cool water and seek immediate medical attention.
2. INTRODUCTION
Slimline foldout inspection light for use in confi ned spaces, with 6mm minimum thickness. Inspection arm can be rotated 180° and folded
back for use as a hands-free inspection light. Features 12 SMD LEDs which produce up to 400 lumens, operated by a rolling dimmer switch,
and a 1W SMD LED in the end for use as a directional torch. Suitable for hands-free operation with three magnets and a hanging hook.
Folds away, small and compact, suitable for keeping in your pocket. Powered by a 3.7V 2Ah rechargeable Lithium-ion battery which lasts up
to 8 hours. Supplied with USB charging lead.
3. SPECIFICATION
Model No: ................................................................. LED180
Battery: ................................................. 3.7V 2Ah Lithium-ion
Charging time:...................................................................3hr
IP Rating: ........................................................................IP20
LED Type: ............................................... 12 SMD + 1W SMD
Lumen output: .................................... Side; 400lm, Top; 70lm
Maximum length: ........................................................ 300mm
Minimum length: ......................................................... 155mm
Operating time: ............................ Side; 3hr (400lm), Top; 8hr
4. CHARGING
4.1. The battery fitted to this light is considered to be a consumable item and its ability to accept charge will reduce over time. We will
warranty it against mechanical and electrical defect for a period of one year, this does not cover fair wear and tear. If the battery is not
properly charged before first use, or regularly conditioned, its capacity will diminish. Under these circumstances we will not replace the
battery even if it is less than one year old.
4.2. Connect the charger into the charge socket on the light, see fig.1. Plug into power supply and turn on, the red charge LED on the
light will light as the battery charges. When fully charged the LED turns green.
4.3. When the battery has fully charged (approx 3hrs) Disconnect from mains supply.
Note: The Lithium battery does not suffer from memory effect and once fully charged may be stored for up to six months without
another charge.
© Jack Sealey Limited
12 SMD & 1W SMD LED RECHARGEABLE
SLIM INSPECTION LIGHT
LED180
MODEL NO:
Original Language Version LED180 Issue 2 16/08/21