Daihen OTC WB-P400 Owner's Manual page 76

6
C
W C
HAPTER
ELDING ONDITION
S W
ETTING ELDING
WELDING
METHOD
DC
DC
PULSE
DC WAVE
PULSE
*1: Note that the "collective" voltage adjustment may not meet the appropriate condition if a mixing gas other than those
with the following mixing ratios is used.
*1-1: MAG gas: Argon (Ar) 80 % + Carbon dioxide (CO
*1-2: MIG gas (stainless steel): Argon(Ar) 98 % + Oxygen (O
*1-3: MIG gas (Aluminum/Aluminum bronze/Silicon bronze): Argon (Ar)100 %
*2: Available for applications either of "STANDARD" or "HIGH".
*3: For "STANDARD" mode, the standard mode or extended cable mode (extended mode of power cable) is available.
( 6.7.2.1 F1: Standard/Extended cable mode)
-
6-14
C
ONDITIONS
GAS (*1) WIRE MATERIALS
CO
MILD STEEL
2
MILD STEEL
MAG (20 % CO )
2
(*1-1) MILD STEEL CORED
STAINLESS CORED
STAINLESS STEEL
MIG (2 % O )
2
(*1-2)
STAINLESS FERRITE
SOFT ALUMINUM
HARD ALUMINUM
MIG (100 % Ar)
Brazing CuSi
(*1-3)
Brazing CuAl
MAG (20 % CO )
2
MILD STEEL
(*1-1)
STAINLESS STEEL
MIG (2 % O )
2
(*1-2)
STAINLESS FERRITE
SOFT ALUMINUM
HARD ALUMINUM
MIG (100 % Ar) Brazing CuSi
(*1-3)
Brazing CuAl
INCONEL
MAG (20 % CO )
2 MILD STEEL
(*1-1)
STAINLESS STEEL
MIG (2 % O )
2
(*1-2)
STAINLESS FERRITE
SOFT ALUMINUM
MIG (100 % Ar)
(*1-3)
HARD ALUMINUM
WIRE DIA. [in. (mm)]
030 / .035 / .040 /.045
(0.8/0.9/1.0/ 1.2)
.030 / .035 / .040 /.045
(0.8/0.9/1.0/1.2)
.045 (1.2) STANDARD (*3)
.045 (1.2) STANDARD (*3)
.030 / .035 / .040 /.045
(0.8/0.9/1.0/1.2)
.030 / .035 / .040 /.045
(0.8/0.9/1.0/1.2)
.045 / 1/16 (1.2/1.6)
.045 / 1/16 (1.2/1.6)
.030 / .035 / .045
(0.8/0.9/1.2)
.030 / .035 / .045
(0.8/0.9/1.2)
.030 / .035 / .040 /.045/
.052 (0.8/0.9/1.0/1.2/
1.4)
.030 / .035 / 0.45
(0.8/0.9/1.2)
.030 / .035 / .045
(0.8/0.9/1.2)
.045 / 1/16 (1.2/1.6)
.045 / 1/16 (1.2/1.6)
.030 / .035 / .045
(0.8/0.9/1.2)
.030 / .035 / .045
(0.8/0.9/1.2)
.035 / .045 (0.9/1.2)
.030 / .035 / .040 /.045 /
.052 (0.8/0.9/1.0/1.2/
1.4)
.030 / .035 / .045
(0.8/0.9/1.2)
.030 / .035 / .045
(0.8/0.9/1.2)
.045 / 1/16 (1.2/1.6)
.045 / 1/16 (1.2/1.6)
)20 %
2
)2 %
2
Penetration
TRAVEL SPEED
adjustment
(*2) (*3) Enable
(*2) (*3) Enable
Enable
Enable
(*2) (*3) Enable
(*2) (*3) Enable
(*2) (*3) -
(*2) (*3) -
(*2) (*3) -
(*2) (*3) -
(*2) (*3) Enable
(*2) (*3) Enable
(*2) (*3) Enable
(*2) (*3) -
(*2) (*3) -
(*2) (*3) -
(*2) (*3) -
(*2) (*3) -
(*2) (*3) -
(*2) (*3) -
(*2) (*3) -
(*2) (*3) -
(*2) (*3) -