Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Scotsman CU50PA-1
Summary of Contents for Scotsman CU50PA-1
- Page 1 Installation and User’s Manual for Cube Ice Machine Model CU50...
-
Page 2: Table Of Contents
Introduction: This ice machine is the result of Scotsman’s This manual includes the information needed to decades of experience as an industry leader in the install, start up and maintain the ice machine. Note design and manufacture of both commercial and any Caution or Warning indicators, as they provide residential ice machines. -
Page 3: Specifications
This is a commercial product. If service is needed remain on the unit when the unit is installed on a unit in a residence, use a commercial service outdoors. company. Locate one at www.scotsman-ice.com. Cabinet Dimensions Width Depth, with door panel, handle adds 1 5/8”... -
Page 4: Cabinet Layout
Cabinet Layout 98.55 FLOOR DRAIN ACCESS HOLE 3.88 443.23 17.45 606.68 23.89 566.17 22.29 40.51 377.95 1.60 14.88 753.24 29.66 873.25 DRAIN 34.38 FLEXIBLE TUBING 3/8 I.D. PUMP MODEL (INCLUDED) 5/8 I.D. GRAVITY MODEL (NOT INCLUDED) POTABLE WATER INLET 1/4" COMPRESSION FITTING 97.79 82.99 3.85... -
Page 5: Air Flow & Control Panel
They meet or exceed the the ability of the ice machine to make ice. standards of agencies like U.L. Scotsman assumes no liability or responsibility of any kind for products manufactured by Scotsman that have been altered in any way, including the use of any parts and/or other components not specifically approved by Scotsman. -
Page 6: Water Quality
To keep the machine operating properly, these • be connected to a drain impurities or minerals will have to be regularly dissolved by an acid cleaning, using Scotsman Ice • be connected to the proper power supply Machine Scale Remover. Directions for this may be •... -
Page 7: Door Swing Change
CU50 Installation and User’s Manual Door swing change The door can be attached to open with hinges on 6. Remove original bottom hinge. the left or right. To change: 1. Remove top hinge pin from hinge. 7. Remove two plugs or screws from upper cabinet bracket. -
Page 8: Notes For The Installer
Sealing to floor: In some cases the base of the ice machine must be sealed to the floor to meet local code. Food grade silastic sealant such as Scotsman part number 19-0529-01 is recommended. Place the machine in the intended location. Turn the leg levelers in until the bottom of the unit is as close to the floor as possible. -
Page 9: Installation: Water & Drain
CU50 Installation and User’s Manual Installation: Water & Drain The recommended water supply tubing is ¼ inch Drains OD copper. Install an easily accessible shut-off valve between the supply and the unit. This shut-off There are two types of ice machine models, one valve should not be installed behind the unit. -
Page 10: Gravity Drain
Gravity Drain Caution: Restrictions in the drain system to the 5. Cut an 8” piece of 5/8” ID X 7/8” OD tygon machine will cause water to back up into the ice (clear plastic) tubing. Slide one end of the tube storage bin and melt the ice. -
Page 11: Electrical
CU50 Installation and User’s Manual Electrical The ice machine is supplied with a power cord. Do not remove the grounding pin from the cord’s plug. Do not use extension cords. Follow all codes. Connect the machine to its own 115 volt, 15 amp circuit. -
Page 12: Start Up
Start Up Check list: After about a half hour, ice will fall into the ice storage bin. The machine makes 24 cubes per 1. Has the unit been connected to the proper batch. It is normal for the first batches of ice to water supply? melt, that continues until the bin has cooled. -
Page 13: Use
CU50 Installation and User’s Manual No special instructions are needed for use. Just take as much ice as you need, the machine will replace it. A scoop is provided, and it can be stored in the machine using the loop of tubing on the right side as a holder. -
Page 14: How To Clean The Condenser And Winterize
CU50 Installation and User’s Manual Clean and Sanitize Ice Making System bin after the ice making system has been cleaned, 4. Return the kickplate and front service panel and the storage bin is empty. to their original positions. Fasten them to the cabinet using the original screws. -
Page 15: Clean And Sanitize Ice Making System
3. Press and HOLD the both the Clean-Reset and On/Off buttons for 5 seconds. The Time to Clean light will blink on and off. 4. Pour 8 ounces of Scotsman Ice Machine Scale 3. Turn off the water supply. Remover (available from a local Scotsman Distributor or Dealer) into the ice machine 4. -
Page 16: What To Do Before Calling For Service
What to do before calling for service Installation and User’s Manual Ice cubes are incompletely formed 10. Clean the bin liner of mineral scale by mixing some ice machine scale remover and hot • Clean the ice making system water, and using that solution to scrub the Low capacity scale off of the liner. - Page 17 SCOTSMAN ICE SYSTEMS 101 Corporate Woods Parkway Vernon Hills, IL 60061 800-726-8762 www.scotsman-ice.com 17-3314-01 Rev. A...
Need help?
Do you have a question about the CU50PA-1 and is the answer not in the manual?
Questions and answers