Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for DeWalt D25712-XE
Summary of Contents for DeWalt D25712-XE
- Page 1 INSTRUCTION MANUAL D25712-XE 48 mm (1-7/8") SDS MAX COMBINATION HAMMER ®...
-
Page 2: Definitions: Safety Guidelines
SAVE THESE INSTRUCTIONS Definitions: Safety Guidelines 1) WORK AREA SAFETY The definitions below describe the level of severity for each signal a) Keep work area clean and well lit. Cluttered or dark areas invite accidents. word. Please read the manual and pay attention to these symbols. b) Do not operate power tools in explosive atmospheres, such as in the DANGER: Indicates an imminently hazardous situation which, if presence of flammable liquids, gases or dust. -
Page 3: Electrical Safety
c) Prevent unintentional starting. Ensure the switch is in the off position f) Keep cutting tools sharp and clean. Properly maintained cutting tools with before plugging in. Carrying power tools with your finger on the switch or sharp cutting edges are less likely to bind and are easier to control. plugging in power tools that have the switch on invites accidents. - Page 4 MINIMUM GAUGE FOR CORD SETS • Wear gloves when operating tool or changing bits. Accessible metal parts on the tool and bits may get extremely hot during operation. Small bits of broken For Cable length (m): 7.5 material may damage bare hands. Use Cable with minimum rating (Amperes) Tool Amperes •...
-
Page 5: Markings On Tool
WARNING: Use of this tool can generate and/or disburse dust, which may cause FIG. 1 CHISEL BIT ADJUSTMENT MODE serious and permanent respiratory or other injury. Always use AS/NZS standard approved respiratory protection appropriate for the dust exposure. Direct particles away from face and body. - Page 6 SAVE THESE INSTRUCTIONS FOR FUTURE USE Electronic Speed and Impact Control (Fig. 1, 3) Motor The electronic speed and impact control (G) offers the following advantages: Your D WALT tool is powered by a D WALT-built motor. Be sure your power supply –...
- Page 7 Side Handle (Fig. 1) WARNING: Once assembled, the side handle clamp should never be removed. 3. Screw the side handle (C) into the bush (L) and then into clamp wheel. Tighten WARNING: To reduce the risk of personal injury, ALWAYS operate the tool with the securely.
-
Page 8: Operation
Move the torque control lever (T) to setting 40 Nm or 80 Nm as needed for 4. Pull on the bit to check if it is properly locked. The hammering function requires the bit to be able to move axially several centimetres when locked in the tool application. - Page 9 Drilling with a Solid Bit (Fig. 1) WARNING: The use of a residual current device (RCD) protected supply with a rated residual current of 30 mA or less is recommended. The use of a RCD reduces 1. Insert the appropriate drill bit. the risk of electric shock.
-
Page 10: Maintenance
Brushes (Fig. 3) MAXIMUM CAPACITY The carbon brushes are not user-serviceable. Take the tool to an authorized D WALT D25712-XE repair agent. Concrete 48 mm (1-7/8") The yellow brushwear indicator LED (R) lights up when the carbon brushes are nearly worn out. - Page 11 In addition to the warranty, D WALT tools are covered by our: FREE ONE YEAR SERVICE CONTRACT WALT will also maintain the tool for free at any time during the first year of purchase. This includes labour, parts and lubrication required to restore the product to sound mechanical and/or electrical condition.
- Page 12 WALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286 • 20 Fletcher Road, Mooroolbark, VIC 3138 Australia (JUN10) Part No. N081422 D25711-XE Copyright © 2010 D WALT The following are trademarks for one or more D WALT power tools: the yellow and black color scheme; the “D” shaped air intake grill; the array of pyramids on the handgrip; the kit box configuration;...