Sealey WL53/8D Quick Start Manual

thank you for purchasing a Sealey product. manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
instructions
1. Safety
1.1. eleCtriCal Safety.
uSe only the SuPPlieD Plug for ConneCting lamP to the PoWer SuPPly.
Warning! It is the user's responsibility to read, understand and comply with the following electrical instructions:
‰
You must ensure the risk of electric shock is minimised by the installation of appropriate safety devices.
An RCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board. We also recommend that an RCd
(Residual Current device) is used with all electrical products, particularly portable equipment which is plugged into an electrical
supply not protected by an RCCB.
You must also read and understand the following instructions concerning electrical safety.
1.1.1. The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualified
electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the appliance and
the safety of the appliance operator. If in any doubt about electrical safety, contact a qualified electrician.
1.1.3. You must ensure that you:
Inspect the charger plug, cable and connector for wear and damage to ensure items are safe before connecting to the mains power
supply.
1.1.4. If worn or damaged Do not use.
imPortant: Check that the voltage marked on the plug is the same as the lamp.
1.1.5. Uncoil the cable between charger and the lamp.
Do not pull the charger plug from the mains socket by the lead.
8
Warning! Do not use any other type of plug with this product, other than the supplied mains plug. Failure to observe this warning
‰
could result in injury and or fire and will invalidate the warranty.
Do not try to take the plug apart.
8
Do not use the plug to charge or power any other electrical item.
8
Do not get the plug wet, or use in wet, damp conditions (for indoor use only).
8
2. introDuCtion
Powerful 3 dioptre 85mm & 8 dioptre 22mm precision lens gives high quality magnifying capabilities. Features 45 SMd leds producing up to
550 lumens to illuminate the object for improved detailed work. Includes a built-in touch sensitive dimmer switch. Extremely strong and flexible
neck allowing ease of positioning. Features a G-clamp base to secure to a workbench or table. Also includes a sturdy base which the magnifier
can sit in. Ideal for electrical engineers, engravers and fine detail work. Supplied with BS approved plug.
3. SPeCifiCation
Model no: ............................................................. Wl453/8d
leds: ........................................................................ 45 SMd
nett Weight: ................................................................ 1.08kg
Supply: ...........................................................................230V
4. oPeration
4.1. Please check the box for all the parts. (fig.1)
4.2. attaChing the ClamP
Make sure the light is unplugged while attaching it to the
9
table.
Fix the table clamp on a suitable table, the thickness required
≤44MM, put the adaptor (fig.1) onto the bottom of the lamp
arm and insert it into the table clamp, rotate the lamp arm
to the best position, connect the adapter and turn on
the electricity.
4.3. attaChing the baSe
Make sure the light is unplugged while attaching the base.
9
Remove the adaptor from the bottom of the lamp arm, then
© Jack Sealey limited
Dimmable Dual mounting magnifying
Work light 230V 45 SmD leD
Wl53/8D
Model no:
Lamp Arm
Original Language Version
Base
Adaptor
Power Switch
Wl453/8d Issue 1 20/11/18
Table
Clamp
Power Cable
And Plug
fig.1