Related Manuals for Philips SWW1890/12
Summary of Contents for Philips SWW1890/12
- Page 1 Register your product and get support at www.philips.com/welcome SWW1890 EN User manual...
-
Page 3: Table Of Contents
Contents Important Safety Your Philips Wireless HD Net Connect 5 What is in the box Overview The transmitter The receiver Installation Connect the transmitter to your computer Connect the receiver to the HDTV set Activate your Philips Wireless HD Net Connect and set up the link... -
Page 4: Important
1 Important Safety This ‘bolt of lightning’ indicates uninsulated material within your unit may cause an electrical shock. For the safety of everyone in your household, please do not remove product covering. The ‘exclamation point’ calls attention to features for which you should read the enclosed literature closely to prevent operating and maintenance problems. -
Page 5: Your Philips Wireless Hd Net Connect
Wireless HD Net Connect Congratulations on your purchase and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome. What is in the box Note • Make sure you have all these items in the box. Contact your dealer for any missing or damaged items. -
Page 6: Overview
3 Overview The transmitter Front view Displays the connection status indicator of the transmitter. Connect the transmitter to power jack the computer with the USB cable. Top view INFO Displays on the HDTV the button connection status of the transmitter. HDMI IN Plug into the HDMI port of connector... - Page 7 The Philips Wireless HD Net Connect gives you a total wireless solution to enjoy the content from your computer on your HDTV. The transmitter can transmit an uncompressed video content up to 7 meters (without obstruction between the transmitter and receiver) without latency.
-
Page 8: Installation
4 Installation Connect the transmitter to your computer Connect the transmitter to the computer using the supplied USB cable. Connect the transmitter to the HDMI port of the computer. Connect the small end of the USB cable to the POWER jack of the transmitter; Connect the receiver to the HDTV set Connect the other end of the USB cable... -
Page 9: Activate Your Philips Wireless Hd Net Connect And Set Up The Link
5 Activate your Philips Wireless HD Net Connect and set up the link Turn on the power of your HDTV HDMI HDMI Go to the source menu under the settings menu of your HDTV. Select the HDMI input to which the receiver is connected. -
Page 10: On Screen Display On Hdtv
The maximum transmission range is up to 7 meters without obstruction between the transmitter and receiver. • If more than one set of Philips Wireless HD Net Connect is placed in the same room, make sure that the minimum distance among each one is 2 meters. •... -
Page 11: Mount Your Receiver
6 Mount your receiver You can either mount the receiver on the wall or on the back of the HDTV. Mount your receiver on the wall Select a spot near the HDTV. Drill two holes in the wall. Make sure that the distance between the two holes is 45mm and the diameter of the hole is 5 mm. -
Page 12: Mount Your Receiver On The Back Of The Hdtv
Mount your receiver on the back of the HDTV Remove the white protective film from one of the supplied adhesive tapes. Secure the glued side of the adhesive tape and attach it to the central bottom area of the receiver. Select a flat location on the rear side of the HDTV. -
Page 13: Technical Data
7 Technical data Supported resolution Video format timings Resolution Primary CEA video Timing 480p 640x480p @ 59.94/60Hz 480p 720x480p @ 59.94Hz 480p 720x480p @ 60Hz 576p 720x576p @ 50Hz 720p 1280x720p @ 50Hz 720p 1280x720p @ 59.94/60Hz 1080i 1920x1080i @ 50Hz 1080i 1920x1080i @ 59.94/60Hz... -
Page 14: Notice
One of Philips’ leading Business Principles is to take all necessary health and safety measures for our products, to comply with all applicable legal requirements and to stay well within the EMF standards applicable at the time of producing the products. -
Page 15: Warranty Information
Your system consists of materials which can be recycled and reused if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging materials and old equipment. Warranty information Warranty information can be found at: www. philips.com/support... -
Page 16: Frequently Asked Questions
9 Frequently asked questions The power LED on the receiver is not lit up in red in standby mode. There is no video displayed on my TV screen. f the picture quality is poor, what do I do? Make sure that there is power supply for the receiver. •... - Page 17 I cannot hear any sound or the sound is poor, what do I do? How can I connect to my computer to enable the external display? For Windows7 operation system: For Windows Vista operating system: For Windows XP operating system: •...
- Page 18 For MAC operating system: How can I change the audio setting of my computer to HDMI output? For Windows7 and Vista operating system: For Windows XP operating system: MAC operating system detects the external display equipment and switches to a better resolution automatically when you plug in the display cable to MAC series.
- Page 19 0560 © 2011 Koninklijke Philips Electronics N.V. IFU_SWW1890_EN_V1.3 All rights reserved. WK11293...