Therefore, the following checks should be performed for the continued protection of the customer and servicetechnician. PDP-LX5080D...
Page 3
PRODUCT SAFETY NOTICE With the AC plug removed from an AC power source, place a Many electrical and mechanical parts in PIONEER set have jumper across the two plug prongs. Turn the AC power switch on. special safety related characteristics. These are often not evident...
Page 4
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be installed before shipment. Please be sure to follow this method especially if it is specified in this manual. PDP-LX5080D...
5.5.1 INFORMATION ON SYMPTOMS THAT DO NOT CONSTITUTE FAILURE ............71 5.5.2 FUNCTION OF DECREASING THE BRIGHTNESS LEVEL ................. 75 5.6 OUTLINE OF THE OPERATION ..........................76 5.6.1 PANEL DRIVE-POWER ON / OFF FUNCTION ..................... 76 5.6.2 SPECIFICATION OF THE FAN CONTROL......................77 5.6.3 PROCESSING IN ABNORMALITY ........................78 PDP-LX5080D...
Page 6
10. EXPLODED VIEWS AND PARTS LIST...........................160 10.1 PACKING SECTION ..............................160 10.2 REAR SECTION ...............................162 10.3 FRONT SECTION..............................164 10.4 CHASSIS SECTION (1/2) ............................166 10.5 CHASSIS SECTION (2/2) ............................168 10.6 PANEL CHASSIS SECTION .............................170 10.7 MULTI BASE SECTION ............................172 10.8 PDP SERVICE ASSY ...............................174 PDP-LX5080D...
Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting temperatures (hard to melt/easy to harden). The following lead-free solders are available as service parts: • Parts numbers of lead-free solder: GYP1006 1.0 in dia. GYP1007 0.6 in dia. GYP1008 0.3 in dia. PDP-LX5080D...
: Part is Charged Section. : Part is the High Voltage Generating Points other than the Charged Section. 50F Y DRIVE Assy POWER SUPPLY Unit 50F X DRIVE Assy Conductive plate X AC inlet Power switch Fig. High Voltage Generating Point (Rear view) PDP-LX5080D...
2.2 SPECIFICATIONS 50” plasma television, model : PDP-LX5080D/PDP-LX508D Item Number of pixels 1920 x 1080 pixels 17 W + 17 W (1 kHz, 10 %, 6 Ω) Audio amplifier Sound Effect SRS FOCUS/SRS/SRS TruBass Power Requirements 220 V to 240 V AC, 50 Hz/60 Hz, 421 W (0.3 W Standby) Weight 38.3 kg (84.4 lbs.)
12 PHONES output terminal TIMER indicator 13 INPUT 5 terminal (S-VIDEO) • The TIMER indicator lights up when one or more DTV 14 INPUT 5 terminal (VIDEO) programmes are preset for watching or recording. 15 INPUT 5 terminals (AUDIO) PDP-LX5080D...
Page 12
18 PC INPUT terminal (Audio) COMMON INTERFACE slot 19 DIGITAL OUT terminal (OPTICAL) • For a CA Module with a smart card 20 SPEAKERS terminals (right/left) 10 ANT (Antenna) input terminal • Power can be supplied through this terminal PDP-LX5080D...
Page 13
Turns the power on when the STANDBY indicator lights red. Selects the PC terminal as an input source. Note INPUT 5: Selects INPUT 5 as the input source of the plasma • When using the remote control unit, point it at the plasma television. television. PDP-LX5080D...
Item to be checked regarding video Item to be checked regarding audio Block noise Distortion Horizontal noise Noise Dot noise Volume too low Disturbed image (video jumpiness) Volume too high Too dark Volume fluctuating Too bright Sound interrupted Mottled color PDP-LX5080D...
[MUTING] once, press [ENTER/SET], press [ ] seven times, press 2. Press [ENTER/SET], then select a Mask indication, using [ENTER/SET], then press [ ] seven times.) Press [ ] to select "CLEAR". Hold [ENTER/SET] pressed for at least 5 seconds. After clearance is completed, "ETC" is automatically selected. PDP-LX5080D...
Page 16
11. COMBI MASK SETUP (+) 1. MASK OFF 2. CMB MASK 01 For use while Combination Mask is displayed. • • • • • Use [ ] or [ ] to select the type of mask. 18. CMB MASK 17 PDP-LX5080D...
3.4 JIGS LIST Name Jig No. Remarks 3.5 CLEANING Name Part No. Remarks Cleaning liquid GEM1004 Used to fan cleaning. Refer to “10.4 CHASSIS SECTION (1/2)”. Cleaning paper GED-008 PDP-LX5080D...
Page 21
When ordering service parts, be sure to refer to "EXPLODED VIEWS and PARTS LIST" or "PCB PARTS LIST". mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. PDP-LX5080D...
CLK / LE / HBLK / LBLK R/G/B R/G/B DRIVER IC DRIVER IC DRIVER IC DRIVER IC DRIVER IC DRIVER IC DRIVER IC IC1681 IC1671 IC1661 IC1651 IC1871 IC1861 IC1851 50F ADDRESS L ASSY 50F ADDRESS S ASSY A B C PDP-LX5080D...
Page 25
CLK / LE / HBLK / LBLK R/G/B R/G/B DRIVER IC DRIVER IC DRIVER IC DRIVER IC DRIVER IC DRIVER IC DRIVER IC DRIVER IC IC1681 IC1671 IC1661 IC1651 IC1681 IC1671 IC1661 IC1651 50F ADDRESS L ASSY 50F ADDRESS L ASSY PDP-LX5080D...
SCART OUT INPUT(AUDIO) for MAIN ASSY INPUT(VIDEO) INPUT1 INPUT2 INPUT3 INPUT5 AIR_SIF INPUT5 PC AUDIO DETECT for SIDE IO ASSY BLOCK RST_MSP I2S_EMMA SPDIF_EMMA SPDIF_HDMI for SIDE IO ASSY A_NG_B for MAIN ASSY R OUT L OUT SP TERMINAL PDP-LX5080D...
4.14 POWER SUPPLY BLOCK of 50LED&IR and SIDE KEY ASSYS FHD IR ASSY V+3_3V_STB U9731 RPM7240-H5 FHD RLS ASSY OP AMP V+3_3V_UCOM IC9781 MM3012XN IC9782 AMS114YD01 SIDE KEY ASSY V+3_3V_STB S9501 to S9506 PDP-LX5080D...
The LEDs flash only while the 200ms data copied for panel is turned on. backup In the process of 100ms rewriting the program 100ms of the microcomputer During factory operation During reservation video recording (Unit: Standby) During reservation video recording (Unit: ON) PDP-LX5080D...
: The IF microcomputer sends the operation data of the remote control unit (or KEY) to the main microcomputer. : The main microcomputer issues a startup command (PON) to the MOD microcomputer. : The relay is controlled with logical OR interpretation of control signals by the main microcomputer and module (MOD) microcomputer. PDP-LX5080D...
V+6.5V ucom V+5.1V Vsus Vadr VSUS Digital DRF_B VADR X/Y Drive Address BAK_EEP ASIC ADDRESS Scan Power DRIVE DCDC/REG DRIVE/SCAN Sensor The user operation is invalid. (All LED: OFF) Among standby power devices, only the IF microcomputer periphery operates. PDP-LX5080D...
Page 42
V+6.5V ucom V+5.1V Vsus Vadr Digital DRF_B VSUS VADR X/Y Drive Address BAK_EEP Scan ASIC ADDRESS Power DRIVE DCDC/REG DRIVE/SCAN Sensor Remote control unit waiting state. (Red LED: ON) Among standby power devices, only the IF microcomputer periphery operates. PDP-LX5080D...
Page 43
Address BAK_EEP ASIC ADDRESS Scan Power DRIVE DCDC/REG DRIVE/SCAN Sensor Remote control unit waiting state. (Red LED: ON) Standby power device and some Vcc power devices operate. RGB-SW/AD/D-AMP are electrified, but uses the power-saving mode function of the IC. PDP-LX5080D...
Page 44
EEPROM V+6.5V ucom V+5.1V Vsus Vadr VSUS Digital DRF_B VADR X/Y Drive Address BAK_EEP ASIC ADDRESS Scan Power DRIVE DCDC/REG DRIVE/SCAN Sensor A state when it displays a picture on the PDP. (Blue LED: ON) All devices are electrified. PDP-LX5080D...
Is there any local abnormality Is the abnormality associated Replace the panel chassis. with a single scan line? on the screen? with one ADDRESS or one TCP? Failure analysis for the Failure analysis for the drive system => DR3 drive system => DR4 PDP-LX5080D...
Page 46
Is an external video signal MAIN Assy => MA3 displayed properly? Problems concerning the audio output No Failure analysis for the Is the audio signal output? audio system => AU1 Specific failure whose cause is difficult to identify in the initial stage PDP-LX5080D...
Replace the POWER SUPPLY 200 and 210 V (VSU: 125/35°C). specified range? Unit. The ripple must be within 10 V. Is there a fluctuation in the Replace the POWER SUPPLY Unit. VSUS voltage? The POWER SUPPLY Unit is normal. PDP-LX5080D...
Properly connect the panel FPC Replace the FFC cables. Is the input signal normal? connectors properly connected to and SCAN Assys connectors. the X/Y DRIVE Assys? Replace the panel chassis. Replace the X/Y DRIVE Assys. Replace the DIGITAL Assy. PDP-LX5080D...
Page 49
Is the input signal normal? Replace the FFC cables. (See the oscilloscope photos.) Replace the DIGITAL Assy. Is the waveform of the control signal from the SCAN Assy normal? Replace the Y DRIVE Assy. (See the oscilloscope photos.) Replace the SCAN IC. PDP-LX5080D...
Page 50
Are all the connectors properly Reconnect the connectors. connected? Is the TCP control signal normal? Is the input signal normal? (See the oscilloscope photos.) (See the oscilloscope photos.) Replace the panel chassis. Replace the FFC cables. Replace the DIGITAL Assy. PDP-LX5080D...
Page 51
Is the waveform of the SCAN IC Replace the Y DRIVE Assy. control signal from the Y DRIVE Assy normal? Replace the SCAN IC. Replace the panel chassis. PDP-LX5080D...
Replace the MAIN Assy. Replace the MAIN Assy. Is the indication position correct? It is most likely that the sync signal is abnormal. Is the tone correct? It is most likely that the video signal data are missing. Replace the MAIN Assy. PDP-LX5080D...
SIDE KEY and MAIN Assys. Can the unit be turned on, using Replace the 232C or MAIN Assys. Replace the MAIN Assy. RS-232C commands? Failure in the RS-232C driver and its peripheral circuits Failure in the Main microcomputer. Replace the MAIN Assy. PDP-LX5080D...
Replace the MAIN Assy. detection on the Factory menu IC5201? coincide with the input signal data? Replace the MAIN Assy. Is the sync signal input to IC8001? Replace the MAIN Assy. No problem with the MAIN Assy. Replace the MAIN Assy. PDP-LX5080D...
Page 60
TP6106 High? casting stream, Tuner or COFDM is defective. Has the Bitstream output (digital signal, 0 to 3.3 V) arrived at R6260 Replace the IC6205, IC6206 and IC6207. near the IC6206 EMMA is defective. Replace the MAIN Assy. PDP-LX5080D...
X9101. IC9152? 49 50 If there was no ploblem replace the MSP5651M. (pins 2, 3, 5, 6) Are signals output from IC9151 Check the IC9151, IC9152 and peripheral circuit. and IC9152? Repair the failure points. (pins 1, 7) PDP-LX5080D...
Connectors CN3801 EXT_PD line: Open disconnection detection UNKNOW DIGITAL Assy It becomes "UNKNOW" except ModuleUcom can not Each PD line of ModuleUcom above-mentioned PD detection detection condition. UVP: Under Voltage Protection, OVP: Over Voltage Protection, OCP: Over Current Protection PDP-LX5080D...
Page 66
Y DRIVE Assy SCAN A, B, C, D 4 (SCN-5V) CN2801, CN2902 Assy SCAN A, B, C, D Assy CN3002, CN3101 CN1602, CN1802 DIGITAL Assy 8 (ADRS) ADDRESS Assy CN1601, CN1801 X DRIVE Assy, 8 (ADRS) Y DRIVE Assy PDP-LX5080D...
Page 67
IC5V SCN5V_PD voltage detection DCDC converter drive stop SCAN Hi Unconnect SCAN Low Unconnect YDRV_PD disconnection detection Decrease voltage 15VDD detection VNOFS VKOFS1_2 Decrease voltage YDD_PD detection VKOFS3 VKOFS4 Decrease voltage VPRST detection Increase or decrease SCAN_PD voltage detection PDP-LX5080D...
In a case of color difference 4:2:2, Y, Cb, and Cr use 12 bits each, but Cb and Cr are transmitted at a half sampling rate of Y. This unit is capable of processing the upper 10 bits out of 12 bits of video data. Recent high-end DVD players, such as Pioneer DV-79AVi, are capable of outputting 10-bit color-difference signals.
Page 72
Confirmation of the manufacturer of the connected equipment Check if the connected equipment was manufactured by Pioneer and if it supports the HDMI Control function. If its manufacturer is not Pioneer, proper operations are not guaranteed.
Page 73
• The AV device, such as an AV amplifier, and the HD AV Converter are not connected simultaneously. • The HDMI Control function must be activated on the HD AV Converter. (For details, refer to the instruction manual of the HD AV Converter.) PDP-LX5080D...
Page 74
If the following occurs even if the operation check is performed properly, a failure, such as breakage of the HDMI cable, problems on the side of the HD AV Converter, and problems with the MAIN Assy, may be suspected: • The HD AV Converter cannot be turned off. PDP-LX5080D...
Detection example: Protection against panel cracking 80 °C. High-temperature protection function 2 The count of plasma discharge with regard to the APL will be decreased if the panel temperature becomes 55 °C or higher. APL (average picture level) PDP-LX5080D...
OFF, or by performing no operation for 10 seconds or more during Standby mode. When the panel drive-power is ON When the panel drive-power is OFF POWER SUPPLY Unit POWER SUPPLY Unit DRF-SW-B (TEST PIN) DRF-SW-B (TEST PIN) Alligator clip Multi base Multi base PDP-LX5080D...
• When the temperature rises, the sensor voltage of TEMP2 decreases. • When the voltage of the DAC output for external FAN decreases, rotation speed of FAN rises. PDP-LX5080D...
DTB antenna the monitoring conditions, an SD log is created, and the ANT_POW_B = L when the signal is L (100 mS, short-circuited LED flashes for 60 sec. A shutdown process is not 3 times) performed in the power system. PDP-LX5080D...
Page 79
A specific LED flash pattern (blue LED, 13 times) starts. The next PON operation is valid, and the flag is cleared upon the next power-on. If RST4 is H, a restoration process starts according to the latest power-on/-off status. PDP-LX5080D...
Page 80
UART. Upon receiving the data, the main microcomputer orders a specific LED flash pattern (blue LED, 4 times). The next PON operation is valid, and the flag is cleared upon the next power-on. PDP-LX5080D...
How to exit Service Factory Mode By using a PDP service remote control) • PDP service remote control : press [FACTORY] key. • Supplied remote control unit : press [HOME MENU] key. By issuing RS-232C commands) • Issue [FAN]. PDP-LX5080D...
(HDMI settings, etc.). • Data on screen (i.e., screen position; meaning clock dividers, and not including data on screen size). Are reset to the default values (data stored in memory will be retained). Screen size will be retained. PDP-LX5080D...
(Note 1) When ten seconds have passed since the [DRIVE OFF] key was pressed at the standby, it becomes invalid. Please press [POWER] key from the [DRIVE OFF] key pressing within ten seconds when you do power supply ON while driven OFF. PDP service PDP-LX5080D remote control PDP-LX508D PDP-LX5080D...
This key cannot turn the unit off. The AV SELECTION settings are changed POWER OFF cyclically. Press this key to turn off the unit. This key cannot turn the unit on. POINT ZOOM Not used with this model. ZOOM +/- Not used with this model. PDP-LX5080D...
Equivalent to MKS+S00 RST MASK 01 <=> <=> 48V <=> 50V <=> 60V <=> Equivalent to MKS+S51 60P <=> 72V <=> 75V <=> • • • • • • RST MASK 25 <=> Equivalent to MKS+S75 *: Setting value PDP-LX5080D...
Page 86
6.2.3.3 SYNC DET (+) 6.2.4 INITIALIZE 6.2.4.1 SIDE MASK LEVEL (+) SIDE MASK LEVEL <=> 6.2.4.2 FINAL SETUP DATA RESET <=> NO <=> YES Exclusively used for 6.2.4.3 Wide XGA AUTO <=> DISABLE <=> ENABLE technical analysis (details omitted) PDP-LX5080D...
3 Color system and Signal type Color System and Signal Type At Composite At S-connector Input Input NTSC PAL M PAL N PAL 60 SECAM 4.43 NTSC BLACK/WHITE Y/CB/CR Y/PB/PR Digital Video signal Option (Destination, Panel Generation, etc.) Options Step-up D model PDP-LX5080D...
Page 88
DOT BY DOT ì ì ì ì FULL ì − ZOOM ì − CINEMA ì − WIDE ì − FULL 14:9 ì − CINEMA 14:9 ì: supported, −: unsupported (∗): It is effective only with models having the Full HD panel. PDP-LX5080D...
In the 19-24 rows, the version of the execution program is displayed. • PANEL INFO: It displays the generation of the panel, inchage and the type of the panel. For details on display values and settings, see "10: Panel Information" in "9.3.1. QS1 (PANEL STATUS)." PDP-LX5080D...
Page 90
0 6 0 – N T V – R S I 0 0 0 1 O R D 1 2 3 4 Step-up D Display Example Meaning Item Name DTV Hardware Version DTV HARD 0001 User Password PASSWORD 1234 PDP-LX5080D...
Page 91
PS/RST Failure to DTV Starting D-ANT Abnormally in the anntenna power supply of DTV tuner RST-MA M-DCDC Abnormally in RST2 of MTB. (power decrease of DC-DC converter) RELAY Relay Power Supply MA-EEP IIC communication line between EEPROM and MAIN PDP-LX5080D...
Page 92
] key is pressed, {CLEAR <=> :YES} ⇔ {CLEAR <=> :NO} is repeated. Even if [ ] key or [ If the [ENTER/SET] key is kept on pressing for 5 second when the status of this menu is <YES>, clear process will begin. PDP-LX5080D...
Page 93
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ • Display/Meaning Meaning Item Name Display Example Corresponding RS-232C Command HOUR METER (PANEL) PANEL 00151H 21M POWER ON COUNTER P-COUNT 00000095 TIMES SYSTEM SERIAL SERIAL Note: The PANEL-side's HOUR METER/P-COUNT acquires information from the PANEL-side. PDP-LX5080D...
Page 94
HDMI mode status ---- BIST NVAL N value CTSVAL CTS value AKSV Shadow AKSV value BKSV Shadow BKSV value IT CNT IT content (AVI info) EXTCOL Extension calorimetry (AVI info) RGV QR RGB range (AVI info) PIXDEP Number of pixel/bit PDP-LX5080D...
Page 96
CC-CRI detection 20Ch 60Ch XDS content advisor 0 20Dh 60Dh XDS content advisor 1 Note: The SVDEC data display in the Regular A, D model, but the value is not settled because the multi-screen display function is not used. PDP-LX5080D...
RASTER MASK SETUP (+) The mask indication (RASTER) can be set and indicated. 6.2.2.10 PATTERN MASK SETUP (+) The mask indication (PATTERN) can be set and indicated. 6.2.2.11 COMBI MASK SETUP (+) The mask indication (COMBI) can be set and indicated. PDP-LX5080D...
Page 98
• P-COUNT: The accumulated power-on count is indicated. • TEMP1: The current panel temperature and the historical maximum temperature recorded in memory are indicated. The range of temperature indication is from -50.0 to +99.9. (The temperature unit is " °C (Centigrade) ".) PDP-LX5080D...
Page 99
MAIN EEPROM Communication Error MDU-IIC MD-IIC BACKUP BACKUP EEPROM Communication Error DAC1 DAC1 Communication Error DAC2 DAC2 Communication Error − − Abnormally in RST2 power supply RST2 High temperature of the panel TEMP-H Panel temperature TMP-NG Low temperature of the panel TEMP-L PDP-LX5080D...
Page 100
<VOL+> : Adding by 10 to the adjustment/ setting value <VOL-> : Subtracting by 10 from the adjustment/setting value F S E < = > <SET> : Determining the adjustment/setting value and shifting to the upper layer PDP-LX5080D...
Page 101
The number of the adjustment table and the drive sequence currently selected are displayed on the right side of the third line as the On-Screen display. Drive sequence and adjustment table Sequence Name Video50 Video60 Video72 Video75 PC60 Adjustment Value TBL2 TBL1 TBL1 TBL3 TBL4 Table PDP-LX5080D...
Page 102
: Shifting to the previous item <RIGHT> : Adding by one to the adjustment/ setting value <LEFT> : Subtracting by one from the adjustment/setting value <SET> : Determining the adjustment/setting value and shifting to the upper layer – < = > – PDP-LX5080D...
Page 103
: Shifting to the previous item <RIGHT> : Adding by one to the adjustment/ setting value <LEFT> : Subtracting by one from the adjustment/setting value <SET> : Determining the adjustment/setting value and shifting to the upper layer < = > O P R T PDP-LX5080D...
Page 104
• The MASK indication sequence can be changed among 48V, 50V, 60V, 72V, 75V and 60P, using the Right or Left key. The selected sequence and the ABL/WB table are retained until the mask is turned off. PDP-LX5080D...
Page 105
• The MASK indication sequence can be changed among 48V, 50V, 60V, 72V, 75V and 60P, using the Right or Left key. The selected sequence and the ABL/WB table are retained until the mask is turned off. PDP-LX5080D...
Page 106
• The MASK indication sequence can be changed among 48V, 50V, 60V, 72V, 75V and 60P, using the Right or Left key. The selected sequence and the ABL/WB table are retained until the mask is turned off. PDP-LX5080D...
Page 107
6.2.3.3 SYNC DET (+) Exclusively used for technical analysis 6.2.3.1 EDID WRITE MODE <=> Exclusively used for production line. 6.2.3.2 CH PRESET <=> Exclusively used for production line. 6.2.3.3 SYNC DET (+) Exclusively used for technical analysis (details omitted). PDP-LX5080D...
To ensure proper function of the product, leave the AC cable unplugged for 1 minute or more before plugging it again. If the AC cable is plugged back in immediately after unplugging, software for the DTV block may not start up properly. 6.2.4.3 Wide XGA AUTO <=> Exclusively used for technical analsyis (details omitted). PDP-LX5080D...
Terminal panel B Multi base Front Chassis HT (508F) Assy, Terminal panel A Section Front Chassis HB Assy (50), Panel holder V1 (50), V2 (50), Front chassis VL (508F) PANEL TANSHI DIGITAL SENSOR SCAN A SCAN B SCAN C SCAN D PDP-LX5080D...
Remove the rear case (508F). Tightening sequence for the screws when assembling When assembling the rear case (508F), tighten the screws in the following sequence: Tighten the two screws. Tighten three screws. Tighten the two screws. Tighten the eight screws. Tighten other screws. PDP-LX5080D...
Page 111
When removing the POWER SUPPLY Unit, be sure to remove POWER SUPPLY not only the POWER SUPPLY Unit Unit but entire PCB base. PCB base Styling of jumper wires around the FAN motor 50F Y DRIVE POWER SUPPLY Assy Unit PDP-LX5080D...
Page 112
Upon servicing, be sure to restore the original wiring of the unit after repair work. Tightening sequence for the screws when assembling When assembling the terminal panel B, tighten the screws in the following sequence: Tighten the screw. Tighten the screw. Tighten other screws. PDP-LX5080D...
Page 113
Remove the Front case Assy, by pulling it upward. Rivet Front side Turn it not to press the rivet. When assembling the front case, (Because when the rivet presses, fit in once again.) tighten this rivet first. PDP-LX5080D...
Page 114
Access to 50F DIGITAL Assy Desconnect the flexible cable. Multi base section Remove the two screws. Remove the four screws. Lift the Multi base section to the direction of the arrow. Multi base section Multi base section PANEL SENSOR Assy 50F DIGITAL Assy PDP-LX5080D...
Page 115
IR Assy FHD RLS Assy 50FHD LED Assy Panel holder V1 (50), V2 (50) Remove the two screws. Unhook the six hooks. Remove the panel holders V1 (50) and V2 (50). Panel holder V2 (50) Panel holder V1 (50) PDP-LX5080D...
Page 116
50F SCAN D Assy Assy Assy Assy Notes for Three pieces connector 40P* Three pieces connector 40P is a precision part. Pay attention to the handling. Connecting Method Disconnecting Method In addition, please do not touch the electrode plane. PDP-LX5080D...
No adjustment required PANEL SENSOR Assy Writing of backup data is required. Refer to the “8.2 BACKUP OF THE EEPROM (DIGITAL ASSY)”. Other assemblies No adjustment required (*) : When replacing the MAIN Assy, be sure to perform the FINAL SETUP. PDP-LX5080D...
Page 118
“8.5 ADJUSTMENTS WHEN THE DRIVE ASSYS ARE REPLACED. No adjustment required ADDRESS Assy No adjustment is required after replacement of parts PANEL SENSOR Assy other than those mentioned above. No adjustment required TANSHI Assy PDP-LX5080D...
1 Turn on the unit, using the remote control unit or by issuing the PON command. Then issue the FAY command. 2 Issue the BCP command to transfer the data stored in the EEPROM for backup. 3 Turn the power off. PDP-LX5080D...
Page 120
1 Turn on the unit, using the remote control unit or by issuing the PON command. Then issue the FAY command. 2 Issue the UAJ command to delete data stored in the EEPROM on the DIGITAL Assy. 3 Issue the BCP command to transfer the data stored in the EEPROM for backup. 4 Turn the power off. PDP-LX5080D...
Page 121
When a DIGITAL Assy with an EEPROM in which adjustment data are stored is mounted, this step is not required after manual adjustment. ("DIGITAL EEPROM: REPAIR" is not indicated.) (2) Method using the RS-232C commands Issue the FAJ command. PDP-LX5080D...
P COUNT INFO. < = > : NO OPRT Right P COUNT INFO. < = > : CLEAR SET (5 sec) MAX TEMP. < = > : NO OPRT MAX TEMP. < = > : CLEAR Right SET (5 sec) 3 Turn the power off. PDP-LX5080D...
[DIZ S03] : Dither ON, L dither ON, noise OFF. [$1800000001] : LUT mode ON [$1000003F00] : Reset active control OFF. ∗: If the unit is shut down during the above adjustment flow, resend the above commands from the beginning. PDP-LX5080D...
Page 124
(RST MASK 22: Cyan 3SF) Checking VOL YNOFS3/4/1 (min) (RST MASK 16: Green 1023+) Replacement with the parts for service Checking VOL YNOFS3/4/1 (min) • Re-replacement of the panel (RST MASK 15: Red 1023+) • Replacement of the DRIVE Assy PDP-LX5080D...
Page 125
: To set the gamma G value to that for Factory mode [PGB S00] : To set the gamma B value to that for Factory mode [DIZ S03] : Dither ON, L dither ON, noise OFF. [$1800000001] : LUT mode ON [$1000003F00] : Reset active control OFF. PDP-LX5080D...
Page 126
(Check on the PANEL 1-ADJ menu.) Return VOL OFFSET to the tentative setting value. / [VOF ∗∗∗] Determine the tentative setting value for VOL OFFSET as the final value. From the Recovery flowchart (1-2) and (1-4) [To the Main flowchart (2)] PDP-LX5080D...
Page 127
Determine the tentative setting value for VOL YNOFS4 as the final value. *1: The tentative setting value becomes the final value. Determine the tentative setting value for VOL YNOFS1 as the final value. From the Recovery flowchart (2-1) and (2-3) [Adjustment completed] PDP-LX5080D...
Page 128
Display RST MASK 02 (Red). / [MKS S52] Set VOL OFFSET to the current setting value plus 112. / [VOF ***] Replacement of abnormal circuits or Is there erroneous discharge (abnormal dead cell)? re-replacement of the panel required (Check on the PANEL 1-ADJ menu.) PDP-LX5080D...
Page 129
(dead cell). The VOL OFFSET value must be 117 or greater. Replacement of abnormal circuits or Current VOL OFFSET < 117? re-replacement of the panel required Display RST MASK 03 (Green). / [MKS S53] [To the Recovery flowchart (1-4)] PDP-LX5080D...
Page 130
(Check on the PANEL 1-ADJ menu.) Set VOL OFFSET to the current setting value plus 64. / [VOF ***] Determine the current VOL OFFSET setting value as the final value. [To the Main flowchart (2)] PDP-LX5080D...
Page 131
Set VOL YNOFS3 to the current setting value +47. / [VY3 ***] Set VOL YNOFS4 to the current setting value +47. / [VY4 ***] Replacement of abnormal circuits or Is there erroneous discharge (abnormal lit cell)? re-replacement of the panel required (Check on the PANEL 1-ADJ menu.) PDP-LX5080D...
Page 132
Set VOL YNOFS4 to the current setting value plus 4. / [VY4 ∗∗∗] Replacement of abnormal circuits or Current VOL YNOFS3 setting value > 137? re-replacement of the panel required Is there erroneous discharge (abnormal dead cell)? [To the Recovery flowchart (2-1)] PDP-LX5080D...
Page 133
Make a note of this VOL YNOFS3 value. Set VOL YNOFS1 to the final setting value of VOL YNOFS3 minus 31. / [VY1 ***] Determine the current VOL YNOFS1 setting value as the final value. [To the Main flowchart (2)] PDP-LX5080D...
Adjust so that "Δ Tsus - gub = Δ Tsus - iub + α ± 5 nsec," using the variable controls shown in the table below: Value of α Assy X DRIVE Assy VR1002 70 nsec Y DRIVE Assy VR2002 60 nsec PDP-LX5080D...
Page 137
(input to the gate terminal of Q2111) SUS-D pulse width: Tsus - Dg Adjust so that "Tsus - Dg = Tsus - D ± 5 nsec," using the variable control shown in the table below: Assy Y DRIVE Assy VR2001 PDP-LX5080D...
Page 138
2 Adjust the pulse width (Tsus - Dg) of the SUS-D Y DRIVE Assy input signal so that it becomes "Tsus-D ± 5 nsec." 1 Measure the SUS-D pulse width (Tsus - D). TP2114 from VR2001 IC2104 DIGITAL Assy Q2111 IC2005_A7 Q2105 IGBT YSUS-D Q2113 IGBT TP2116 PDP-LX5080D...
9.1.2 USING RS-232C COMMANDS Individual ports are provided for RS-232C and SR+ connectors with this model. Therefore, unlike the case of previous models, which required switching of exclusive operation between these connectors on the Integrator menu, switching is no longer required. PDP-LX5080D...
To subtract ∗∗∗ to the adjustment value (∗∗∗ = 000 to 999, designated by a function command) Determining the flag of the DIGITAL Assy adjustment in "adjustment is completed" Factory mode off Factory mode on Set each memory setting of MTB side to the shipment state. PDP-LX5080D...
Page 142
Horizontal stripes every eight white lines 5 for perfect linear 6 for perfect linear 7 for perfect linear 8 for perfect linear Mask for ABL adjustment Raster - White Raster - Red Raster - Green Raster - Blue Raster - Black PDP-LX5080D...
Page 143
Set the power consumption setting of the panel side to Energy saving 1 Set the power consumption setting of the panel side to Energy saving 2 Factory mode: off Setup at shipment Factory mode: on Independent gamma Blue S∗∗ Independent gamma Green S∗∗ PDP-LX5080D...
Page 144
Room light sensor operation at panel side ∗∗∗ User white balance - Red low light UP*/DN* is not effective S∗∗ Setting of red level for panel degradation correction ∗∗∗ RESET1ST_KSB adjustment UP*/DN* is not effective ∗∗∗ RESET2ND_KSB adjustment UP*/DN* is not effective PDP-LX5080D...
Page 145
Theater port interlock operation OFF Theater port interlock operation ON Determining the flag for the DIGITAL Assy adjustment in "not adjusted" To add ∗∗∗ to the adjustment value (∗∗∗ = 000 to 999, designated by a UP∗ function command) PDP-LX5080D...
Page 146
UP*/DN* is not effective ∗∗∗ UP*/DN* is not effective YSTL_KSB adjustment ∗∗∗ UP*/DN* is not effective YSTL_HZ adjustment ∗∗∗ Y-SUS-B adjustment UP*/DN* is not effective Initializing the video EEPROM data Initializing the setting data to which no adjustment command is provided PDP-LX5080D...
2: Panel Generation 5: Panel Product Form 7th byte Under bar System model 8th byte 2nd PLANT All-in-one design TV 1st PLANT PLANT information and SQ_LSI version Monitor ∗ mismatching (version mismatching at SD) Standard module ‘ Others Simple module PDP-LX5080D...
Adjustment completed 13: MASK indication X-DRV Adjustment not MASK-OFF completed X-DCDC MASK-ON X-SUS DIG-DCDC 14 to 17: Details of power 3: Adjustment-data protection function Not used backup Normal Not used With backup data At detection UNKNOWN No data (default) PDP-LX5080D...
3 byte Pulse meter B 1 8 byte 00000000 Pulse meter B 2 8 byte 00000000 Pulse meter B 3 8 byte 00000000 Pulse meter B 4 8 byte 00000000 Pulse meter B 5 8 byte 00000000 2 byte PDP-LX5080D...
Data from the hour meter for the seventh latest PD 8 byte 00000213 Eighth latest "1st PD" data 1 byte Eighth latest "2nd PD" data 1 byte Data from the hour meter for the eighth latest PD 8 byte 000001A7 2 byte PDP-LX5080D...
Data from the hour meter for the seventh latest SD 8 byte 00000000 TEMP1 (high temperature) Eighth latest SD data 1 byte TEMP1 (low temperature) Eighth latest SD subcategory data 1 byte Data from the hour meter for the eighth latest SD 8 byte 00000000 2 Byte PDP-LX5080D...
Go to No. 12 Subcategory Information 13(D) Failure of Power Supply at MTB side Go to No. 13 Subcategory Information 15(F) Failure of Main EEPROM Immediately Shutdown *: Indicates the frequency of Blue LED flashing when the shutdown is occurred. PDP-LX5080D...
Page 156
< No. 13 Subcategory Information on "Failure in MSP/MAP Shutdown Power supply at MTB side" > AV Switch Shutdown RGB Switch Shutdown Value Shutdown Factor Remarks (Operation) RST 2 Shutdown VDEC Shutdown RST 4 Shutdown VDEC-SDRAM Shutdown AD/PLL Shutdown HDMI Shutdown COFDEM Shutdown PDP-LX5080D...
Power switch is set to OFF, or 10 seconds or more has elapsed without any operation in Standby mode. The DRIVE OFF key on the remote control unit for servicing functions the same as the DRVS00 command. (A function equivalent to that of the DRVS01 command [DRIVE ON] is not available with the remote control unit for servicing.) PDP-LX5080D...
[CBU] To make the flag setting that Writing F0 to the 2 k byte ROM The backup ROM is indicating that backup data initialized. have not been copied To copy Digital backup data to [BCP] Copying backup data EEPROM PDP-LX5080D...
For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions, apply as you think it appropriate.) 10.1 PACKING SECTION UK only PDP-LX5080D/YVIXK5 PDP-LX508D/WYVIXK5 only Ferrite core Cable tie Speed clamp ×3...
Page 161
Polyethylene Bag See Contrast table (2) Polyethylene Bag AHG1337 After Image Caution See Contrast table (2) (2) CONTRAST TABLE PDP-LX5080D/YVIXK5, PDP-LX508D/WYVIXK5 and WYV5 are constructed the same except for the following: PDP-LX5080D PDP-LX508D PDP-LX508D Mark Symbol and Description /YVIXK5 /WYVIXK5...
10.2 REAR SECTION MAIN CN4109 MAIN CN4110 (USB) CN8801 CN8802 TANSHI Refer to "10.3 FRONT SECTION". PDP-LX5080D...
Page 163
Screw TBZ40P080FTB Label A (ED) AAX3480 Screw BPZ30P080FTB169 Screw BPZ30P100FTB (2) CONTRAST TABLE PDP-LX5080D/YVIXK5, PDP-LX508D/WYVIXK5 and WYV5 are constructed the same except for the following: PDP-LX5080D PDP-LX508D PDP-LX508D Mark Symbol and Description /YVIXK5 /WYVIXK5 /WYV5 4 Side Input Panel (8ES)
10.4 CHASSIS SECTION (1/2) Refer to "10.7 MULTI BASE SECTION". Cleaning liquid : GEM1004 Cleaning paper : GED-008 FHD FAN CONNECT CN9555 FHD FAN CONNECT FHD FAN CN9553 CONNECT CN9554 MAIN CN4103 Refer to POWER "10.5 CHASSIS SECTION (2/2)". SUPPLY PDP-LX5080D...
Page 167
Screw PPZ50P100FTB Multi Base Holder ANG2937 Screw TBZ40P080FTB Screw ABA1364 (2) CONTRAST TABLE PDP-LX5080D/YVIXK5, PDP-LX508D/WYVIXK5 and WYV5 are constructed the same except for the following: PDP-LX5080D PDP-LX508D PDP-LX508D Mark Symbol and Description /YVIXK5 /WYVIXK5 /WYV5 8 Sub Frame L Assy 507...
10.5 CHASSIS SECTION (2/2) MAIN CN4101 MAIN CN4105 MAIN TANSHI CN4106 CN8806 POWER SW CN9571 AC Inlet MAIN CN4113 Fan×3 Refer to "10.6 PANEL CHASSIS SECTION". PDP-LX5080D...
Page 171
Three Pieces Connector 40P AKM1384 PCB Spacer (Reuse) AEC2087 Gasket AD ANK1948 PCB Spacer (Reuse) AEC2122 (2) CONTRAST TABLE PDP-LX5080D/YVIXK5, PDP-LX508D/WYVIXK5 and WYV5 are constructed the same except for the following: PDP-LX5080D PDP-LX508D PDP-LX508D Mark Symbol and Description /YVIXK5 /WYVIXK5 /WYV5...
10.7 MULTI BASE SECTION 50FHD LED CN9671 SIDE KEY CN9501 50F DIGITAL CN3201 FHD IR CN9731 FHD RLS CN9781 POWER (side) FHD FAN CONNECT CN9551 POWER POWER SIDE IO CN9352 SIDE IO CN9351 PDP-LX5080D...
Page 173
Rear Sheet AMR3747 Multi Base Assy (J) ANA2103 Terminal Panel A (ED) ANC2441 Gasket FE ANK1945 Gasket EC ANK1954 6P Housing Wire (J115) ADX3561 4P Housing Wire (J122) ADX3564 Hex. Head Screw BBA1051 Screw BMZ30P060FTB Screw PMB30P080FNI Screw ABA1354 PDP-LX5080D...
10.8 PDP SERVICE ASSY PDP SERVICE ASSY 508F AWU1272 (for PDP-LX5080D/YVIXK5) PDP SERVICE ASSY 508F-E AWU1273 (for PDP-LX508D/WYVIXK5, /WYV5) Exterior Section PDP-LX5080D...
Page 175
ANE1662 Upper Carton (508F service) AHD3637 NSP 20 Drive Voltage Label ARW1097 Protect Sheet AHG1331 (2) CONTRAST TABLE PDP-LX5080D/YVIXK5, PDP-LX508D/WYVIXK5 and WYV5 are constructed the same except for the following: PDP-LX5080D PDP-LX508D PDP-LX508D Mark Symbol and Description /YVIXK5 /WYVIXK5 /WYV5...