Hitachi C 10FCH2 Handling Instructions Manual page 6

4. Using the Vise Assembly (Standard accessory) (Fig. 6)
(1) The vise assem bly can be m ounted on either the left
fence {Fence (B)} or the right fence {Fence (A)} by
loosening the 6 m m w ing bolt (A).
6 m m Wing Bolt (B)
Fence (B)
Vise Shaft
6 m m Wing Bolt (A)
(2) The screw holder can be raised or low ered according
to the height of the w orkpiece by loosening the 6 m m
w ing bolt (B). After the adjustm ent, firm ly tighten the
6 m m w ing bolt (B) and fix the screw holder.
(3) Turn the upper knob and securely fix the w orkpiece
in position.
WARNING
Alw ays firm ly clam p or vise to secure the w orkpiece
to the fence; otherw ise the w orkpiece m ight be thrust
from the table and cause bodily harm .
CAUTION
Alw ays confirm that the m otor head does not contact
the vise assem bly w hen it is low ered for cutting. If
there is any danger that it m ay do so, loosen the 6
m m w ing bolt and m ove the vise assem bly to a
position w here it w ill not contact the saw blade.
5. Install the sub fence (B) (Fig. 7)
In the case of direct angle cutting and angle cutting,
use the sub fence. The sub fence (B) can be installed
on the right side of the guide fence (B). Place the
attached plate (A) in the position as show n in Fig. 7,
i n ser t t h e t i p i n t h e g r o o v e o f f en ce (B) an d
sim ultaneously, insert flathead screw M 6 into fence
(B), sub fence (B), and plate (A), then tighten nylon
nut M 6 w ith the included 10m m box w rench until the
sub fence (B) can sm oothly rotate. Then, you can
realize stable cutting of the m aterial w ith a w ide back
face.
Plate (A)
Sub fence (B)
M 6 Nylon nut
Fence (B)
6
Screw Holder
Knob
Vise Plate
Workpiece
Fig. 6
M 6 Flat screw
Fig. 7
WARNING
In the case of left bevel cutting, rotate the sub fence
(B). Supposing it is not able to rotate it, It w ill contact
the blade or som e part of the tool, causing in serious
injury to operator.
6. Using an ink line
Upon low ering the m otor section, the low er guard is
raised and the saw blade appears.
Align the ink line w ith the saw blade.
CAUTION
Never lift the low er guard w hile the saw blade is
rotating.
Th e su b f en ce w i l l n o t o n l y m ake co n t act an d
adversely affect cutting accuracy, this could also result
in dam age to the guard.
7. Install the side handle (Fig. 8)
Rem ove the M 10 bolt and install the side handle that
cam e enclosed w ith this unit.
8. Posit ion adjust m ent of laser line (Only M odel
C10FCH2)
Ink lining can be easily m ade on this tool to the laser
m arker. A sw itch lights up the laser m arker (Fig. 9).
Depending upon your cutting choice, the laser line
can be aligned w ith the left side of the cutting w idth
(saw blade) or the ink line on the right side.
The laser line is adjusted to the w idth of the saw blade
at the tim e of factory shipm ent. Adjust the positions
of the saw blade and the laser line taking the follow ing
steps to suit the use of your choice.
Sw itch
Laser line
M 10 Bolt
Fig. 8
Fig. 9