Sealey POWER TOOLS HS100CE Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS, AND CAUTIONS.
USE THIS PRODUCT CORRECTLY, AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY
CAUSE DAMAGE, AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY.
1. SAFETY INSTRUCTIONS
LEAD PAINT WARNING!
1.1.
of such paint is toxic and must therefore be avoided. The following action must be taken before using this tool:
1.1.1 User must determine potential hazard relating to age of paint to be removed (modern paints do not have lead content).
1.1.2. DANGER! Keep all persons and pets away from the working area. The following persons are particularly vulnerable to the effects
of lead paint dust: expectant women, babies, and children.
1.1.3. We recommend personal protection by using the following safety items: Paint Spray Respirator (Our ref SSP16EN), PE Coated
Hooded Coverall (Our ref SSP266), Latex Gloves (Our ref SSP24).
1.1.4. Take adequate measures to contain the paint dust, flakes, and scrapings.
1.1.5. Continue to wear safety equipment as in (1.1.3) above, and thoroughly clean all areas when task is complete. Ensure the paint
waste is disposed of in sealed bags or containers.
1.2. ELECTRICAL SAFETY
FWARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any other
connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety devices.
A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We also recommend that a Residual Current
Device (RCD) is used. It is particularly important to use an RCD with portable products that are plugged into a supply which is not protected
by an RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual Current Device by contacting your Sealey dealer.
You must also read and understand the following instructions concerning electrical safety.
1.2.1. The Electricity at Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualified
electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.2.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those appliances
and the safety of the appliance operators. If in any doubt about electrical safety, contact a qualified electrician.
1.2.3. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. See 1.2.1. and 1.2.2.
and use a Portable Appliance Tester.
1.2.4. Ensure that cables are always protected against short circuit and overload.
1.2.5. Regularly inspect power supply cables and plugs for wear or damage and check all
connections to ensure that none is loose.
1.2.6. Important: Ensure that the voltage marked on the appliance matches the power supply
to be used and that the plug is fitted with the correct fuse - see fuse rating at right.
1.2.7. DO NOT pull or carry the appliance by the power cable.
1.2.8. DO NOT pull the plug from the socket by the cable.
1.2.9. DO NOT use worn or damaged cables, plugs or connectors. Immediately have any faulty
item repaired or replaced by a qualified electrician. When an ASTA/BS approved UK
3 pin plug is damaged, cut the cable just above the plug and dispose of the plug safely.
Fit a new plug according to the following instructions (UK only).
a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
b) Connect the BROWN live wire to the live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable outer insulation
extends beyond the cable restraint and that the restraint is tight.
Double insulated products, which are always marked with this symbol
To rewire, connect the wires as indicated above - DO NOT connect either wire to the earth terminal.
1.2.10. Products which require more than 13 amps are supplied without a plug. In this case you must contact a qualified electrician to ensure that a
suitably rated supply is available. We recommend that you discuss the installation of an industrial round pin plug and socket with your electrician.
1.2.11. If an extension reel is used it should be fully unwound before connection. A reel with an RCD fitted is preferred since any appliance
plugged into it will be protected. The cable core section is important and should be at least 1.5mm
capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the use of
2.5mm section cable. If extension reel is to be used outdoors, ensure it is marked for outdoor use.
2
1.3 GENERAL SAFETY
!Disconnect the system from the mains power before changing accessories, servicing or performing other maintenance.
!Use correctly rated extension lead.
!Maintain the gun in good condition (use an authorised service agent).
!Use recommended accessories only (non-recommended accessories can be hazardous and will invalidate your warranty).
!Wear appropriate protective clothing and equipment. Work gloves and eye protection are mandatory. Also wear non skid shoes
and protective hair covering to contain long hair. Remove loose fitting garments and jewellery.
!Evaluate your working area before using the gun. i.e. ceiling, floors and enclosures may contain flammable materials.
!Keep the work area clean, uncluttered and well lit. Use the gun only in a well-ventilated area.
!Ensure that small or irregular shaped objects are secured in a vice or clamps before you work on them.
!Clean working surface before using the gun in a free standing vertically position (dust or dirt will be taken up into the air inlet).
!Avoid unintentional starting (if the gun stops during operation, disconnect it from the power supply and have it serviced
by an authorised service agent).
!Stay alert! Always pay attention to the work at hand when operating this gun.
!Guard against electric shock by preventing contact with grounded surfaces (i.e. pipes, radiators, etc.)
Instructions For:
HOT AIR GUNS
Model Nos:
Paint once contained lead as a traditional ingredient. Contact with the dust from the removal
HS100CE/HS102/HS102K
Blue
Neutral
Wire
FUSE RATING 13 AMP
, are fitted with live (brown) and neutral (blue) wires only.
, but to be absolutely sure that the
2
HS100CE, HS102 & HS102K - 1 - 151002
Yellow & Green
Earth Wire
Brown
Live
Wire
Cable
Restraint