Sealey HS102.V3 Quick Start Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear protective
instruction gloves
manual
1. SAFETY
1.1. ELECTRICAL SAFETY
WARNING! It is the user's responsibility to check the following:
‰
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and all
electrical connections for wear and damage. Sealey recommend that an RCd (Residual Current device) is used with all electrical
products. You may obtain an RCd by contacting your local Sealey stockist.
If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable Appliance
Test) tested.
electrical safety information, it is important that the following information is read and understood.
1.1.1. ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2. Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3. Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the correct
fuse - see fuse rating in these instructions.
DO NOT pull or carry the appliance by the power cable.
8
DO NOT pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a firm grip on the plug.
8
DO NOT use worn or damaged cables, plugs or connectors. ensure that any faulty item is repaired or replaced immediately by a
8
qualified electrician.
1.2.
This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a
qualified electrician.
Class II products are wired with live (brown) and neutral (blue) only are marked with the Class II symbol;
A) Connect the BROWN live wire to the live terminal 'L'.
B) Connect the BLUE neutral wire to the neutral terminal 'N'.
C) After wiring, check that there are no bare wires and ensure that all wires have been correctly
connected.
ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
DO NOT connect either wire to the earth terminal.
Sealey recommend that repairs are carried out by a qualified electrician.
1.2.1. If an extension reel is used it should be fully unwound before connection. A reel with an RCd fitted
is preferred since any appliance plugged into it will be protected. The cable core section
is important and should be at least 1.5mm², but to be absolutely sure that the capacity of the reel is suitable for this product and for others
which may be used in the other output sockets, we recommend the use of 2.5mm² section cable. If an extension reel is to be used
outdoors, ensure it is marked for outdoor use.
1.3. GENERAL SAFETY
disconnect the system from the mains power before changing accessories, servicing or performing other maintenance.
9
Use correctly rated extension lead.
9
maintain the gun in good condition (use an authorised service agent).
9
Use recommended accessories only (non-recommended accessories can be hazardous and will invalidate your warranty).
9
Wear appropriate protective clothing and equipment. Work gloves and eye protection are mandatory. Also wear non-slip shoes
9
and protective hair covering to contain long hair. Remove loose fitting garments and jewellery.
9
evaluate your working area before using the gun. i.e. ceiling, floors and enclosures may contain flammable materials.
9
Keep the work area clean, uncluttered and well lit. Use the gun only in a well-ventilated area. Ensure that small or irregular shaped
9
objects are secured in a vice or clamps before you work on them.
Clean working surface before using the gun in a free standing vertically position (dust or dirt will be taken up into the air inlet).
9
Avoid unintentional starting (if the gun stops during operation, disconnect it from the power supply and have it serviced
9
by an authorised service agent).
9
Stay alert! Always pay attention to the work at hand when operating this gun.
9
Guard against electric shock by not contacting grounded surfaces (i.e. pipes, radiators, etc.)
9
maintain correct balance and footing.
9
Keep the gun handle dry, clean and free from oil and grease. Clean dry paint or varnish from the nozzle and scrapers after use.
9
Allow the gun to cool before storing (only store away when cold). Store the gun in a safe, dry place out of reach of children.
9
© Jack Sealey limited
HOT AIR GUNS
model no:
Wear eye Warning!
protection Hot surface
Original Language Version
HS102.V3 & HS102K.V3
HS102.V3 & HS102K.V3 Issue 2 (1)
Recommended fuse rating
13 Amp
30/09/19