Sealey HS105 Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instructions protection
1. SAFETY
1.1. ELECTRICAL SAFETY
WARNING! It is the user's responsibility to check the following:
‰
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
all electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. You may obtain an RCD by contacting your local Sealey Stockist.
If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable
Appliance Test) tested.
Electrical safety information, it is important that the following information is read and understood.
1.1.1. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2. Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3. Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
correct fuse - see fuse rating in these instructions.
DO NOT pull or carry the appliance by the power cable.
8
DO NOT pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a firm grip on the plug.
8
DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or replaced immediately by a
8
qualified electrician.
1.1.4. This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
Class II products are wired with live (brown) and neutral (blue) only, and are marked with the
Class II symbol;
A) Connect the BROWN live wire to the live terminal 'L'.
B) Connect the BLUE neutral wire to the neutral terminal 'N'.
C) After wiring, check that there are no bare wires and ensure that all wires have been correctly
connected.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
DO NOT connect either wire to the earth terminal.
8
Sealey recommend that repairs are carried out by a qualified electrician.
1.2. GENERAL SAFETY
Disconnect the gun from the mains power before changing accessories, servicing or performing other maintenance.
9
Maintain the hot air gun in good condition, use an authorised service agent.
9
Use recommended accessories only. Unapproved accessories can be hazardous and will invalidate your warranty.
9
Wear appropriate protective clothing and equipment. Work gloves and eye protection are mandatory. Protect long hair and remove
9
loose fitting garments and jewellery. Maintain correct balance and footing and wear non-slip shoes.
Evaluate your work area before using the hot air gun. i.e. ceiling, floors and enclosures may contain flammable materials.
9
Keep the work area clean, uncluttered and well lit. Use the hot air gun only in a well ventilated area.
9
Ensure that small or irregular shaped objects are secured in a vice or clamps before you work on them.
9
Stay alert! Always pay attention to the work in hand when operating this hot air gun.
9
Guard against electric shock by not contacting grounded surfaces, i.e. pipes, radiators, etc. when using electric hand tools.
9
Keep the hot air gun handle dry, clean and free from oil and grease. Clean any paint or varnish from the nozzle after use.
9
Allow the hot air gun to cool before storing (only store when cold). Store the gun in a safe, dry place out of the reach of children.
9
DO NOT direct the hot airflow at yourself, others, animals or plants and DO NOT allow children to operate the hot air gun.
8
DO NOT use the hot air gun in rain or in a wet environment, or in areas of high humidity and damp (i.e. bathrooms, steam rooms, etc.).
8
DO NOT obstruct the hot airflow by blocking or covering the air outlet.
8
DO NOT touch the nozzle during, or after, use as it becomes extremely hot.
8
DO NOT leave the hot air gun running unattended. Always turn off the power supply.
8
DO NOT use the hot air gun on a task it is not designed for.
8
DO NOT use the hot air gun in combination with chemical strippers.
8
DO NOT operate the hot air gun when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
▲ DANGER! DO NOT USE THE HOT AIR GUN AS A HAIR DRYER.
© Jack Sealey Limited
1600W HOT AIR GUN 375°C/500°C
MODEL NO:
Wear protective Hot surfaces
gloves
Original Language Version
HS105
Wear a mask
Recommended fuse rating
13 Amp
HS105 Issue 1 03/08/2020