How To Use Electric Home Shower; How To Use - Panasonic DH-3ND1 Operating Instructions Manual

HOW TO USE ELECTRIC HOME SHOWER

1. HOW TO USE

1. Turn "On" the Main Water Valve.
2. Switch "ON" the Miniature Circuit Breaker (MCB) and ON/OFF DP (double pole) Switch.
3. Push up the ELB Reset Lever if it is down.
4. Turn the Water Volume Knob clockwise.
• Turning it clockwise increases the volume of water thus decrease the
water temperature.
• Turning it anticlockwise decreases the volume of water thus increase the
water temperature.
5. Press the Push On-Off Lever.
(a) Water will flow out of the Shower Head and momentarily there will be a stream of air bubble.
(b) Simultaneously, the LCD Display illuminates.
(c) The LCD Display will display the Temperature Indicator, Clock, Shower Head Indicator, e-Hybrid
Indicator & e-Cycle Indicator. (When the power ON, the temperature becomes 38 °C)
(d) To stop the water flow, press the Push On-Off Lever again.
(e) This Lever control both water and electricity supply to the set.
CAUTION
6. Temperature setting.
(a) The shower temperature can be gradually controlled by pressing either "-" or "+" Button.
(b) Each press of the button will either reduce or increase the temperature by 1 °C.
Continuous press of the button will either continuously reduce or increase the temperature.
(c) Lowest adjustable temperature is 32 °C.
(d) Further press of the button will change the display to "PO" which is power off mode
(shower temperature will be same as inlet water temperature).
(e) Highest adjustable temperature is 48 °C.
(f) When the word "MAX" appear at the Power Display and higher temperature is required, reduce the water flow by turning
the Water Volume Knob anticlockwise until "MAX" disappear.
(g) In case of continuous usage at high temperature setting, water temperature will increase and it may cause the control device to
activate temporarily resulting water temperature to drop.
7. Water flows will gradually change from Rain Shower Head to Shower Head by turning the
Diverter anticlockwise.
Note:
Water volume will decrease if the water flows simultaneously at the Shower Head
and Rain Shower Head.
8. When using this Shower Head, select the preferred shower with the Shower Select Button.
Please press the button fully.
Shower
Shower
Select
Head
Button
CAUTION
Press Push On-Off Lever before and after each
shower.
Press the Push On-Off Lever only. Do not pull.
Do not turn "On" and "Off" the Main Water Valve to
operate the shower Unit to avoid any possible damage.
For DH-3NDP1 only
To ensure Pump reliability, Push On-Off Button
must be pressed before and after each shower.
Do not pull. Do not turn "On" and "Off" the Main Water Valve
to operate the shower Unit to avoid any possible damage.
Press
Do not block the Shower Head and Rain Shower Head with hand,
towel or bend the hose. The water flow rate will drop and
water temperature may become very hot.
- 26 -
JET PUMP
Health Safe
Hot
o
Cool
C
Normal Bubble
Max
Beat
PM Level
- +
e-Cycle Set e-Hybrid
ELB Test
Push On-Off
ELB Reset
Push Up
ELB: ON condition
Note:
When stopping the water flow, change shower selection from
Wide Shower to Spot Shower or change the Shower type,
some water will continue to drip from Shower Head or Rain
Shower Head for less than 2 minutes. This is normal due to
some waterremain in the Shower Head and Rain Shower
Head,this is no abnormality to the Unit.
JET PUMP
Health Safe
Hot
o
Cool
C
Normal Bubble
Max
Beat
PM Level
- +
e-Cycle Set e-Hybrid
ELB Test
Push On-Off
ELB Reset
Push Up
ELB: OFF condition
LCD Display &
JET PUMP
Control Panel
Health Safe
Hot
o
Cool
C
Normal Bubble
Max
Beat
PM Level
- +
e-Cycle Set e-Hybrid
ELB Test
Push On-Off
ELB Reset
Push Up
Make sure push at the
center of Push On-Off
Lever only.