Extron electronics XPA 1002 User Manual
Xtra series half-rack 2-channel and mono channel audio power amplifiers
Hide thumbs
Also See for XPA 1002:
- User manual (31 pages) ,
- Setup manual (2 pages) ,
- Specifications (2 pages)
Table of Contents
Advertisement
Quick Links
Extron USA - West
Extron USA - East
Extron EMEA
Headquarters
+800.633.9876
+800.3987.6673
+800.633.9876
Inside USA / Canada Only
Inside Europe Only
Inside USA / Canada Only
+1.919.863.1794
+31.33.453.4040
+1.714.491.1500
+1.919.863.1797 FAX
+31.33.453.4050 FAX
+1.714.491.1517 FAX
© 2008 Extron Electronics. All rights reserved.
Extron Asia
Extron Japan
Extron China
Extron Middle East
+800.7339.8766
+81.3.3511.7655
+400.883.1568
+971.4.2991800
Inside Asia Only
+81.3.3511.7656 FAX
Inside China Only
+971.4.2991880 FAX
+65.6383.4400
+86.21.3760.1568
+65.6383.4664 FAX
+86.21.3760.1566 FAX
User's Manual
XTRA Series: XPA 1002,
XPA 2001–70V, and XPA 2001–100V
Half-Rack 2-Channel and Mono Channel
Audio Power Amplifiers
68-1351-01 Rev. A
10 08
Advertisement
Table of Contents
Related Manuals for Extron electronics XPA 1002
Summary of Contents for Extron electronics XPA 1002
- Page 1 © 2008 Extron Electronics. All rights reserved. User’s Manual Extron China Extron Middle East +400.883.1568 +971.4.2991800 Inside China Only +971.4.2991880 FAX +86.21.3760.1568 +86.21.3760.1566 FAX XTRA Series: XPA 1002, XPA 2001–70V, and XPA 2001–100V Half-Rack 2-Channel and Mono Channel Audio Power Amplifiers 68-1351-01 Rev. A 10 08...
- Page 2 English 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point Important Safety where they exit from the apparatus. Instructions 11. Only use attachments/accessories specified by the manufacturer. This symbol is intended to alert the user of important operating and maintenance 12.
- Page 3 Consignes de Sécurité • Français Ce symbole sert à avertir l’utilisateur que la documentation fournie avec le matériel contient des instructions importantes concernant l’exploitation et la maintenance (réparation). Ce symbole sert à avertir l’utilisateur de la présence dans le boîtier de l’appareil de tensions dangereuses non isolées posant des risques d’électrocution.
-
Page 4: Table Of Contents
... 1-2 Chapter Two • Installation ... 2-1 Application Examples ... 2-2 Mounting the XPA 1002 and XPA 2001 Tabletop use ... 2-3 UL rack mounting guidelines ... 2-3 Rack mounting ... 2-4 Rack mounting ventilation recommendations ...2-5 Flexible conduit adapter kit installation ... 2-6 Installing the flexible conduit kit ...2-7... -
Page 5: Chapter One • Introduction
Table of Contents, cont’d XTRA Series Chapter One Introduction About this Manual Features All trademarks mentioned in this manual are the properties of their respective owners. 68-1351-01 Rev. A 10 08 TOC-ii XTRA Series • Table of Contents... -
Page 6: About This Manual
Series of power amplifiers: the XPA 1002 two-channel stereo audio power amplifier and the XPA 2001 mono audio power amplifier. The XPA 1002 outputs 60 watts per channel at 8 ohms and 100 watts per channel at 4 ohms. The XPA 2001 offers two models: the XPA 2001-70V and the XPA 2001-100V. -
Page 7: Chapter Two • Installation
Introduction, cont’d XTRA Series Chapter Two Installation Application Examples Mounting the XPA 1002 and XPA 2001 XTRA Series • Introduction... -
Page 8: Mounting The Xpa 1002 And Xpa 2001
XPA 2001 Series application example Mounting the XPA 1002 and XPA 2001 The XPA 1002 and XPA 2001 audio amplifiers can be set on a table; mounted on a rack shelf; or mounted in the plenum space above a ceiling-mounted projector. -
Page 9: Rack Mounting
(e.g. use of power strips). Rack mounting The XPA 1002 or XPA 2001 can be mounted in a rack shelf using the optional RSU 129 1U Universal rack shelf (Extron part #60-190-01) or the 1U Basic rack shelf (Extron part #60-604-01), as follows. -
Page 10: Flexible Conduit Adapter Kit Installation
L requirements The Underwriters Laboratories (UL) requirements listed below pertain to the installation of the flexible conduit onto a XPA 1002 or XPA 2001. • This unit is not to be used beyond its rated voltage range. - Page 11 Installation, cont’d Lift Cover Straight Up Remove the 2 screws holding the hot (line) and neutral wires from the terminal block on the PCB. Blue Wire Remove screws (both sides) to release IEC connector plate. Remove the ground wire nut from the grounding stud on the bottom of the enclosure, as shown above.
-
Page 12: Chapter Three • Operation
Installation, cont’d XTRA Series Chapter Three Operation Front Panel Features and Operation Rear Panel Features and Operation XTRA Series • Installation 2-10... -
Page 13: Front Panel Features And Operation
Operation Front Panel Features and Operation OVER TEMP LIMITER/PROTECT SIGNAL XPA 1002 Front Panel OVER TEMP LIMITER/PROTECT SIGNAL XPA 2001-70V, XPA 2001-100V Front Panel Power indicator LED — This LED lights: • Green when the amplifier is receiving full power. -
Page 14: Rear Panel Features And Operation
Operation, cont’d Rear Panel Features and Operation 100-240V 0.5A, 50-60Hz LISTED 17TT AUDIO/VIDEO APPARATUS LEVEL LIMITER/ PROTECT SIGNAL XPA 1002 Rear Panel 100-240V 0.5A, 50-60Hz LISTED 17TT AUDIO/VIDEO APPARATUS LEVEL 80 Hz LIMITER/ PROTECT SIGNAL XPA 2001-70V Rear Panel 3b 4 100-240V 0.5A, 50-60Hz... -
Page 15: Remote Volume Control
The XPA 1002's output power can be effectively doubled by using only one input channel and bridging the output. The XPA 1002 will output 200 watts @ 8 ohms or 120 watts @ 16 ohms in bridged mode. See "Bridged mono output" in this chapter for wiring instructions when bridging the XPA 1002. - Page 16 The XPA 1002's output power can be effectively doubled by using only one input channel and bridging the output. The XPA 1002 will output 200 watts @ 8 ohms or 120 watts @ 16 ohms in bridged mode. See "Bridged mono output" in this chapter for wiring instructions when bridging the XPA 1002.
-
Page 17: Remote Volume Control
Pinout diagram for VCM 100 MAAP connection to XPA's remote connector Bridged mono output The power output of the XPA 1002 can be effectively doubled by bridging the output. Bridging allows power to be output at 200 watts @ 8 ohms or 120 watts @ 16 ohms. -
Page 18: Appendix A • Reference
Mono Source Un-Balanced Wiring From Mono Source 5 mm Captive Screw To 8/16 Ohm Speaker Load XTRA Series • Operation 3-12 XPA 1002 INPUTS REMOTE OUTPUT VOL/MUTE CLASS 2 WIRING STANDBY Input Amplified Output XTRA Series A ppendix A Reference... - Page 19 N 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu Audio output Number/signal type XPA 1002 ... 1 stereo, 4- or 8-ohm direct XPA 2001-70V ... 1 mono, 70 V line XPA 2001-100V ... 1 mono, 100 V line Connectors XPA 1002 ...
- Page 20 Specifications, Part Numbers, Accessories, cont’d General Power ... 100 VAC to 240 VAC, 50/60 Hz, internal Typical ... 26 watts (1/8 power [pink noise] at 8 ohms) Quiescent ... 10 watts Standby ... <1 watt (triggered by contact closure or after 1 hour with no signal) Temperature/humidity ...
- Page 21 Specifications, Part Numbers, Accessories, cont’d Included Parts These items are included in each order of the XPA 1002 or XPA 2001-70V. Included parts Replacement part number XPA 1002 two-channel power amplifier XPA 2001-70V single-channel power amplifier XPA 2001-100V single- channel power amplifier (1) 4-pole screw lock 5.08 mm captive screw plug...
- Page 22 Specifications, Part Numbers, Accessories, cont’d XTRA Series • Reference XTRA Series • Reference...
- Page 23 Specifications, Part Numbers, Accessories, cont’d XTRA Series • Reference A-10...
Need help?
Do you have a question about the XPA 1002 and is the answer not in the manual?
Questions and answers