Advertisement
4. OPERATION
NOTE: Read and fully understand the safety instructions before using this driver.
WARNING: Turn engine off, disconnect the spark plug and allow to cool before
‰
re-filling with fuel or making any adjustment.
4.1.
Unscrew piling socket retainer and fit appropriate piling socket (fig.1).
Refit retainer before use.
4.2.
When initially starting the engine from cold, prime the unit by depressing the
priming bulb three or four times (fig.1).
4.3.
When the engine is started from cold for the first time, close the choke (fig.1).
4.4.
Sharply pull the starter pull cord (fig.1) to it's extent and allow it to rewind gently
under control. The engine should start after 2-4 pulls.
4.5.
When running, re-open the choke and allow to idle until running smoothly before
using.
4.6.
Once running smoothly, squeeze the throttle lever to achieve the required speed.
4.7.
Optimum running speed is mid-range.
DO NOT run engine at high speed when not being used as a driver.
8
4.8.
To turn the engine off, slide the engine cut off switch (fig.1) to the stop position. Reset switch after use or the engine will not fire.
5. MAINTENANCE
WARNING: Turn driver off and disengage the spark plug before cleaning, re-filling with fuel/grease, making any adjustment
‰
or replacing components.
5.1.
AIR FILTER
5.1.1.
Unclip the filter housing (fig.1) and remove the filter.
5.1.2.
Clean filter using warm water and detergent. Dry thoroughly before replacing.
5.2.
SPARK PLUG
5.2.1.
Gently brush the carbon / sediment from tip of spark plug using a wire brush
or emery paper.
5.2.2.
Gently clean the facing surfaces of the electrodes using very fine emery cloth
or similar and set the gap between them to be 0.5 to 0.7mm wide.
5.3.
IMPACT CYLINDER LUBRICATION
5.3.1.
After 50 hours usage, remove impact lubrication hole plug (fig.1, fig.2) using
hex key supplied.
5.3.2.
Top up level from lubricant tube and replace threaded plug when completed.
5.4.
FUEL FILTER
5.4.1.
If the fuel filter is blocked the engine will exhibit reduced performance. To clean the filter it is necessary to remove it from inside the
fuel tank using a long wire hook to gently pull it out of the filler neck. Replace carefully once cleaned of debris / sludge.
5.5.
GENERAL CLEANING
5.5.1.
Brush off unit and exhaust housing to ensure adequate ventilation around the cylinder heat sink fins.
5.6.
STORAGE
5.6.1.
Store driver in the storage container provided.
5.6.2.
Clean and dry unit and empty fuel tank before storing.
6. TROUBLESHOOTING
Symptom
Poor starting / poor running
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
© Jack Sealey Limited
Possible cause
Spark plug soiled
Fuel shortage, filter blocked
Check choke position
Air filter clogged
01284 703534
sales@sealey.co.uk
Original Language Version
Choke
Primer bulb
Starter pull
cord
Engine cut
off on far side
Throttle
fig.1
fig.2
Solution
Clean spark plug (section 5.2)
Top up / Clean See section 5.4
See section 4.3
See section 5.1
www.sealey.co.uk
PPD100
Air filter
Exhaust
housing
Impact
lubrication
cover plate
Piling socket
retainer
Issue 1
29/03/21
Advertisement
