Table of Contents
Related Manuals for GE DPSB620EC
Summary of Contents for GE DPSB620EC
- Page 1 Safety Instructions Operating Instructions Troubleshooting Tips Consumer Support Write the model and serial numbers here: Model # ______________ Serial # ______________ Owner’s Manual DPSB620 DPSB650 175D1807P534 49-90266 11-05 JR...
-
Page 2: What To Do If You Smell Gas
LP fuels. Properly adjusted dryers will minimize incomplete combustion. Exposure to these substances can be minimized further by properly venting the dryer to the outdoors. Installation and service must be performed by a qualified installer, service agency or the gas supplier. -
Page 3: Proper Installation
PROPER INSTALLATION This dryer must be properly installed and located in accordance with the Installation Instructions before it is used. If you did not receive an Installation Instructions sheet, you can receive one by visiting ge.com or by calling 800.GE.CARES (800.432.2737). - Page 4 Do not allow children to play on, with or inside this or any other appliance. WHEN USING YOUR DRYER I Never reach into the dryer while the drum is moving. Before loading, unloading or adding clothes, wait until the drum has completely stopped.
- Page 5 See the Loading and Using the Dryer section. I If yours is a gas dryer, it is equipped with an automatic electric ignition and does not have a pilot light. DO NOT ATTEMPT TO LIGHT WITH A MATCH.
- Page 6 Quick Start Guide for Model DPSB620. You can locate your model number on the label on the front of the dryer, behind the door. Clean the lint filter. IMPORTANT: Clean the lint filter each time you use the dryer. Add clothes. Do not overload. This wastes energy and causes wrinkling.
-
Page 7: Timed Dry
Easy Touch Selections for Model DPSB620. Your new dryer offers the convenience of starting your dryer loads with our E selection, and your LOAD SIZE, DRYNESS LEVEL and TEMP SETTING are automatically set. Then all you have to do is press START. - Page 8 Quick Start Guide for Model DPSB650. You can locate your model number on the label on the front of the dryer, behind the door. Clean the lint filter. IMPORTANT: Clean the lint filter each time you use the dryer. Add clothes. Do not overload. This wastes energy and causes wrinkling.
- Page 9 Easy Touch Selections for Model DPSB650. Your new dryer offers the convenience of starting your dryer loads with our E selection, and your LOAD SIZE, DRYNESS LEVEL and TEMP SETTING are automatically set. Then all you have to do is press START.
- Page 10 About drying cycles. Throughout this manual, features and appearance may vary from your model. SPEED DRY For small loads that are needed in a hurry, such as sport or school uniforms. Can also be used if the previous cycle left some items damp, such as collars or waistbands. DEWRINKLE Use this feature to remove wrinkles from items that are dry or slightly damp.
- Page 11 For leaving items partially damp. About heat settings. HIGH For regular to heavy cottons. MEDIUM For synthetics, blends and items labeled permanent press. For delicates, synthetics and items labeled Tumble Dry Low. EXTRA LOW For lingerie and special-care fabrics. ge.com...
- Page 12 I If the dryer is running, press once to interrupt the cycle; press again to continue the cycle. STOP If the dryer is running, press once to interrupt the cycle; press again to cancel the cycle. Time Remaining Displays the approximate time remaining until the end of the cycle.
-
Page 13: Anti-Bacterial
The countdown time will be shown in the TIME REMAINING display. NOTE: If the door is opened while the dryer is in DELAY, the countdown time will not restart unless the door is closed and START has been pressed again. -
Page 14: Clean Lint Filter
About cycle status. The cycle status indicator lights (on some models) show what part of the cycle the dryer is in and remind you to clean the lint filter. On models without indicator lights, the cycle status will show in the display. - Page 15 (on some models) The stainless steel used to make the dryer drum provides the highest reliability available in a GE dryer. If the dryer drum should be scratched or dented during normal use, the drum will not rust or corrode. These...
-
Page 16: About Reversing The Door
(where you removed the filler plugs). Apply firm pressure to get the screw started in new holes. Loosen top screw from each hinge on the dryer face halfway. With one hand holding the top of the door and the other hand holding the bottom, remove the door from the dryer by lifting it UP and OUT. -
Page 17: Loading And Using The Dryer
Do not add fabric softener sheets once the load has become warm. They may cause fabric softener stains. Bounce Fabric Conditioner Dryer Sheets have been ® approved for use in all GE Dryers when used in accordance with the manufacturer’s instructions. Permanent Press/ Gentle/ Do not wash... -
Page 18: Care And Cleaning Of The Dryer
Apply these products away from the dryer. The fabric may then be washed and dried normally. Damage to your dryer caused by these products is not covered by your warranty. -
Page 19: Venting The Dryer
Venting the dryer. For the best drying performance, the dryer needs to be properly vented. The dryer will use more energy and run longer if it is not vented to the below specifications. Carefully follow the details on Exhausting in the Installation Instructions. -
Page 20: Operation
Before you call for service… Troubleshooting Tips Save time and money! Review the charts on the following pages, or visit ge.com. You may not need to call for service. OPERATION Possible Causes Control pads not Controls accidentally put in responding service mode Dryer doesn’t start... - Page 21 In the future, when drying a load with collars and waistbands, choose MORE DRY. • Move dryer to an even floor space or adjust leveling legs as necessary until even. • When combining heavy and light fabrics in a load, choose MORE DRY.
- Page 22 • Try a fabric softener. • Bounce ® Fabric Conditioner Dryer Sheets have been approved for use in all GE Dryers when used in accordance with the manufacturer’s instructions. • Try a fabric softener. • Adjust setting to LESS DRY or DAMP.
-
Page 23: What Is Not Covered
This warranty is extended to the original purchaser and any succeeding owner for products purchased for home use within the USA. If the product is located in an area where service by a GE Authorized Servicer is not available, you may be responsible for a trip charge or you may be required to bring the product to an Authorized GE Service location. -
Page 24: Consumer Support
Caution must be exercised, since improper servicing may cause unsafe operation. Contact Us If you are not satisfied with the service you receive from GE, contact us on our Website with all the details including your phone number, or write to: General Manager, Customer Relations Register Your Appliance Register your new appliance on-line—at your convenience! Timely product registration will allow for...