Related Manuals for Janus G3
Summary of Contents for Janus G3
- Page 1 Line Powered ADA Telephone G3 User’s Manual 415 Oser Avenue, Suite Q, Hauppauge, New York 11788 984-0099 Phone: 800-527-9156 Fax: 631-864-2631 Rev 1 11/20 Email: sales.us@avire-global.com www.januselevator.com...
-
Page 2: Table Of Contents
G3 Phone Layout ........ -
Page 3: Installation
5. Attach phone line to the green connector at “TEL” or the P1 (TELCO) modular phone jack if available. NOTE: See G3 Phone Layout and P.C. Board Diagrams for all connections. CAUTION: To reduce or eliminate any possible interference, it is highly... -
Page 4: G3 Phone Layout
G3 Phone Layout 0.187 2.875 REMOTE INCOMING BUTTON PHONE LINE 0.375 0.500 1.500 MICROPHONE 5.500 3.750 STANDOFFS 4 PLACES SPEAKER MTG HOLES 4 PLACES 0.500 SPEAKER LIGHT WITH RETAINER RED LENS 3.250 24” CABLING FOR ALARM RECEIVED LIGHT... -
Page 5: Board Diagram 1 (Front View)
P.C. Board Diagram 1... -
Page 6: Board Diagram 2 (Back View With Optional Relay/Aux)
P.C. Board Diagram 2... -
Page 7: Board Diagram 3 (Back View With Optional Lm Module)
P.C. Board Diagram 3... -
Page 8: Programming Set-Up Methods
Programming Set-Up Methods There are two methods of setting up the G3 phone for programming. Select the one applicable to your situation as described below. NOTE: The telephone line provided must be a touch tone line.The phone can be programmed at any location and then installed in the elevator cab. -
Page 9: Optional Programming Instructions
9. Enter # # to hang up the phone. Optional Programming Instructions PURPOSE: To Eliminate Autodialing: To disable the G3 unit from dialing a phone number (used on a ring down telephone line). • Enter # 94851 or #9000000 and listen for three beeps. -
Page 10: List Of Commands For Programming Mode
NOTE: If second message is not used, enter ʻ0ʼ for that message. For example, if you want to set to play English only you must program: **810*#. • **7 0 *# - Ring-Thru Converse Mode (Default). With this setting, the G3 will automatically enter two way communication after it has answered an incoming call. -
Page 11: Auxiliary Output Information
NOTE: If you forget the code, the unit can be reset by using the keypad method to program it. • ## - Exits programming mode • **90 *# - Sets the following Default Values: • #*1180183*# - Default Setup Code. •... -
Page 12: Troubleshooting Guide
Troubleshooting Guide Always visually check the phone for loose or shorted wires, physically damaged, or missing components. The phone will not work on a Digital phone line. It will only work on an Analog phone line or an Analog port from a Digital phone system. - Page 13 Problem: Phone dials out but has broken communication Possible Cause: • Check if voice prompt message is being stopped • Check if there is loud background noise in cab • Check location of microphone • Check mounting of unit • Hold unit in hand and test •...
-
Page 14: Specifications
Specifications Input Connections: One shielded twisted pair communication cable (shield should be grounded at the controller only). Phone Line Requirements: Standard (Analog) loop start voice grade touch tone telephone line, PBX, or key system station analog telephone line. Mechanical Size (H x W x D): 5.5in x 3.2in x 0.75in (140mm x 81mm x 19mm) Weight: 0.37lbs (0.17Kg) Electrical Optional AC Adapter: 9-12VDC/VAC @ min.
Need help?
Do you have a question about the G3 and is the answer not in the manual?
Questions and answers