Electronic Protection System; Wall Mounting - Craftsman CMCBL710 Instruction Manual

hot/Cold Pack Delay
When the charger detects a battery pack that is too hot
or too cold, it automatically starts a Hot/Cold Pack Delay,
suspending charging until the battery pack has reached an
appropriate temperature. The charger then automatically
switches to the pack charging mode. This feature ensures
maximum battery pack life.
A cold battery pack may charge at a slower rate than a warm
battery pack.
The hot/cold pack delay will be indicated by the green light
continuing to blink but with the red light continuously
ON. Once the battery pack has reached an appropriate
temperature, the red light will turn OFF and the charger will
resume the charging procedure.

Electronic Protection System

Li‑Ion tools are designed with an Electronic Protection
System that will protect the battery pack against overloading,
overheating or deep discharge. The tool will automatically
turn off and the battery pack will need to be recharged.
Important Charging Notes
1. The charger and battery pack may become warm to the
touch while charging. This is a normal condition, and
does not indicate a problem. To facilitate the cooling of
the battery pack after use, avoid placing the charger or
battery pack in a warm environment such as in a metal
shed or an uninsulated trailer.
2. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp
or other appliance;
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out
the lights;
c. If charging problems persist, take the tool, battery
pack and charger to your local service center.
3. You may charge a partially used pack whenever you
desire with no adverse effect on the battery pack.
Charger Cleaning Instructions

WARNING:
charger from the AC outlet before cleaning. Dirt and
grease may be removed from the exterior of the charger
using a cloth or soft non-metallic brush. Do not use
water or any cleaning solutions.

Wall Mounting

Some CRAFTSMANchargers are designed to be wall
mountable or to sit upright on a table or work surface. If wall
mounting, locate the charger within reach of an electrical
outlet, and away from a corner or other obstructions which
may impede air flow. Use the back of the charger as a
template for the location of the mounting screws on the wall.
Mount the charger securely using drywall screws (purchased
separately) at least 1" (25.4 mm) long, with a screw head
diameter of 0.28–0.35" (7–9 mm), screwed into wood to an
optimal depth leaving approximately 7/32" (5.5 mm) of the
Shock hazard. Disconnect the
screw exposed. Align the slots on the back of the charger
with the exposed screws and fully engage them in the slots.
VersaTrack™

WARNING:
charger is hung on Trackwall.
CRAFTSMAN chargers can be stored on CRAFTSMAN
VersaTrack™ Trackwall. Hooks and accessories are sold
separately. Please refer to the VersaTrack™ Trackwall accessory
sheet for further information.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
ASSEMBLY AND ADJUSTMENTS

WARNING:
personal injury, turn unit off and remove the
battery pack before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.
Blow Tube Assembly (Fig. D)

WARNING:
without tube securely in place. Never reach down into
housing through tube hole.

WARNING:
when you leave blower unattended or when storing,
checking, adjusting, cleaning, or working on blower.
1. To attach the lower tube
the peg 9 of the upper tube
the lower tube opening
together until the tube locks
and an audible click is heard as shown in Fig. D.
2. To attach the blower tube assembly
head 3 , align the peg
the notch 14 on the blower tube assembly opening as
shown in Fig. D.
3. Push the blower tube assembly onto the power head
until the tube locks 6
audible click is heard.
4. Pull on the blower tube assembly
secured in place.
5. To remove the blower tube assembly, squeeze both
tabs 6 on the side of the power head and pull the
blower tube assembly off.
Do not charge batteries while
To reduce the risk of serious
Do not operate blower
Always remove the battery
4 to the upper tube 5
5 with the notch
11 and push the two tubes
6 engage the blower tube
12 to the power
13 on the power head with
engage the blower tube
12 to ensure it is
English
, align
10 of
5 and an
7