Auto Speaker Setup Using The Setup Microphone - Panasonic SA-XR700 Operating Instructions Manual

Auto speaker setup using the setup microphone

Using the supplied setup microphone, you can measure such items as distance from the seating area, polarity and size
and make adjustment for connected speakers.
Keep quiet during the auto speaker setup. Conversational voice, air-conditioning noise and small sounds made by winds may cause an error or
produce an incorrect setting. Speakers output loud test signals during the auto speaker setup. Make sure to keep little children out of the room.
• Mute the TV volume before starting the auto speaker setup.
• When the subwoofer is connected, make sure it is turned on. (There are subwoofer models that turn off automatically.)
Set the subwoofer volume to the normal listening level.
" "
POWER
RECEIVER
AV
SYSTEM
RECORDER
TV
TUNER PLAYER
CD VCR
BAND ANALOG 6CH
VOLUME
0
DIRECT
TUNING
DISC ENTER
XM CAT XM CH
SKIP SLOW/SEARCH
STOP PAUSE PLAY
DRIVE SELECT CM SKIP
ENTER
SUB MENU RETURN
XM DISPLAY
SUBWOOFER
OFF DIMMER
LEVEL EFFECT VOL
NEO : 6 TV/VIDEO
SFC AUTO
MUSIC MOVIE TEST MUTING
To cancel the setup
halfway
Press [TEST, –AUTO].
Note
• The setup microphone is sensitive to heat. Keep it away from direct sunlight and avoid placing it on top of the unit.
• These settings remain effective after the unit goes off.
• The setup microphone jack is for use with the setup microphone only. Do not connect other microphones.
• The volume may reach an extremely high level when you repeat the auto speaker setup.
When the auto speaker setup is finished, check the volume before starting playback.
Such factors as speaker types, room conditions and speaker placement may cause the unit to set speaker size, lowpass filter frequency and other
items differently for the same type of speakers or produce settings that differ from the actual characteristics of respective speakers.
When sound from speakers seems odd, check the following settings. When you find undesirable settings, correct them manually.
24
• See "Setting speakers and their sizes", "Setting distances" and "Setting the lowpass filter" (á page 35).
RQT8739
INPUT SELECTOR
BI-AMP SURROUND
ADVANCED DUAL AMP WIRELESS READY MULTI ROOM
POWER
SPEAKERS
-MENU/-SETUP ENTER SURROUND SPEAKERS
RETURN AUTO DETECTOR -MULTI ROOM
- -
MENU/ SETUP ENTER SURROUND SPEAKERS
RETURN
AUTO DETECTOR -
1
To turn the unit on
Press
• The standby indicator "^" goes off when you turn the unit on.
DVD To select "SPEAKERS A"
2
BD/DVD
Press
CH
Connect the setup microphone.
3
4 Place the setup microphone.
• Place the setup microphone on a flat surface to
stabilize it.
Examples: a level bench sharing the height with
the seating area, a top section of a sofa etc.
• Set the microphone at seated ear height.
• Use a tripod (for camera and other products) for
best results.
To start the setup
5
TV
Press and hold
• The "AUTO SPEAKER SETUP" indicator flashes.
• When all auto settings are made, "COMPLETE " appears and the "AUTO SPEAKER SETUP" indicator lights on.
• The auto speaker setup takes about 3 minutes to finish in the case of a 5.1-channel system.
• The unit cancels the auto speaker setup halfway through when you give a different
operational instruction before the setup finishes.
• You can perform other operations after "COMPLETE " is displayed. The unit keeps the
settings even if you move straight on to another operation.
To finish the setup
6
Press
• The unit turns off and on in quick succession for completing the setup.
• Unplug the setup microphone when the setup is finished.
AUTO SPEAKER SETUP HDMI
TUNE
AUX
TUNE
- -
S VIDEO VIDEO L AUDIO R
MULTI ROOM AUX
POWER
8
SPEAKERS
(on the unit) to switch "
A
AUTO SPEAKER SETUP HDMI
AUX
- -
S VIDEO VIDEO L AUDIO R SETUP MIC
AUX
AUTO
(on the remote control) for 2 seconds.
TEST
AUTO
(on the remote control).
TEST
SPEAKERS
A
VOLUME
SETUP MIC
" AUTO SPEAKER SETUP "
W
SETUP MIC W
" on.
A
SETUP MIC
W
W
SPEAKERS
A
Tripod