Related Manuals for Waterdrop WD-G3P800-W
Summary of Contents for Waterdrop WD-G3P800-W
- Page 1 Instruction Manual Read and save these instructions REVERSE OSMOSIS Water Filtration System Model: WD-G3P800-W...
- Page 3 Thanks for your purchase from waterdrop. We value your patronage and appreciate your confidence in us. Counting you among our customers is something for which we are especially grateful. Please let us know if we can do anything else to help.
- Page 5 Contents Installation Instructions Before Installation ................2 Parts list ....................3 Product Introduction ................4 Installation Tips ................... 5 Installation Steps................. 7 Step 1: Install the Feed Water Adapter............6 Step 2: Install the RO Faucet and UV Sterilizer ..........7 Step 3: Install the Drain Saddle ...............8 Step 4: Position the RO system Housing ............8 Step 5: Connect Tubing ...................9 Step 6: Connect Power Cord.................10...
- Page 6 WD-G3P800-W 18.12” *5.67”* 17.72” 800 GPD...
- Page 7 Reverse Osmosis Activated carbon Filter RO:WD-G3P800-N2RO Faucet UV Sterilizer X 1 Set...
- Page 8 “UV Sterilizer”Connector (CB) UV Sterilizer K → H: From feed water adapter to “INPUT” water port. O → G, From faucet power cord to “FAUCET” connector.. R → I: From input of UV Sterilizer to “FILTERED” water port. Q → P: From UV Sterilizer power cord to “UV Sterilizer” connector. L →...
- Page 10 P800 RO Installation...
- Page 11 Step 2: Install the RO Faucet and UV Sterilizer (Non-Air Gap Faucet) Countertop Insert the output (the UV Sterilizer end without lamp ring) of UV sterilizer onto UV Sterilizer faucet stem fully and Power Cord firmly, and pop the lock clip on the fitting.
- Page 12 1. Paste the foam seal onto the front plate of drain saddle. Make sure the hole of foam seal is aligned with the hole of front panel (figure 7). Choose a spot on the drain pipe that is convenient for installing the drain saddle. Front Plate Foam Seal Back Plate...
- Page 13 • Remove the plug from the “FILTERED” water port; • Identify the white 1/4” PE tubing; • Insert one end of the tubing into “INPUT” of UV Sterilizer (Figure 13), and pop the lock clip on the fitting. NOTE: Ensure it is fully inserted until it reaches the mark on the tubing. •...
- Page 14 1.Connect the RO faucet to the system: Insert the power cord, which is attached to the RO faucet, into the “FAUCET” connector (Figure 17) and tighten the nut. The faucet connector can be found at the back of the housing. 2.Connect the UV sterilizer to the system: Insert the power cord, which is attached to the UV sterilizer, into the “UV sterilizer ”...
- Page 17 UV Sterilizer Display When you turn on the faucet and water flows through the UV sterilizer, the UV sterilizer starts working and the outer ring of the lamp flashes (Figure 26); The UV sterilizer, only starts up when the faucet is turned on and water flows through it. When the faucet is turned off or there is no water flow, the UV sterilizer stops working immediately (Figure 27);...
- Page 18 Up to 1,600 (for chlorine reduction only) Filter Life: Up to 6 months or 800 gallons (for chlorine reduction only) Filter Life: Up to 24 months or 3,200 gallons Remaining Life (Day) >15 Blue Beeps 2 times when Yellow dispensing Water Keeps beeping when dispensing Water...
- Page 20 The system will flush automatically in one of the following situations: 1.Flush for Accumulative Working Time over 2 Hours To maintain and extend the life expectancy of the filters, the system will be automatically flushed for 20 seconds after working for two hours. While flushing, the front panel screen will show a display similar to what is in Figure 32.
- Page 21 When power is restored after a blackout, the system will be forced to flush automatically for 20 seconds. While flushing, the front panel screen will display as seen in Figure 32. The blue, yellow, and red lights will flash in turn for one second, and then the blue light will be on for 20 seconds.
- Page 23 The system will provide a 90%+ TDS rejection rate(tested under standard laboratory conditions) after full flushing when working properly. If the TDS reading is high, the following are possible causes:...
- Page 25 UV sterilizer doesn’t light up a. The UV sterilizer only starts up when the faucet is turned on and water flows through it. Check if the UV sterilizer power cord is correctly connected, or if you turn on the faucet and water flows through it. is malfunctioning.
- Page 28 Manufacturer Technical Support service@waterdrop lter.com 1-888-352-3558 (U.S.) Mon-Fri 8:00AM-5:00PM (PST) Qingdao Ecopure Filter Co., Ltd. If you encounter any problem with our product, please contact us to get support via the purchase channel. Made in China V020...
Need help?
Do you have a question about the WD-G3P800-W and is the answer not in the manual?
Questions and answers
Remineralization filter installation
how many gallons of wastewater is generated for every gallon of filtered water
The Waterdrop WD-G3P800-W generates 1 cup of wastewater for every 3 cups of filtered water, which equals a 3:1 pure water to wastewater ratio. This means it generates approximately 0.33 gallons of wastewater for every gallon of filtered water.
This answer is automatically generated
RO faucet power chord connection instructions
how do I shut the system down. Getting new cabinets