Roland VersaCamm VS-640 Service Notes page 206

SERVICE MENU HEATER MENU
HEATER MENU SVC. MODE HEAT.
HEATER MENU
HEATER ADJUST
HEATER MENU
PREHEAT TEMP.
HEATER MENU
HEAT TIMEOUT
HEATER MENU
HEATER CHECK
SERVICE MENU SYSTEM SWITCH
SYSTEM SWITCH PAGE1
SYSTEM SWITCH
PAGE16
HISTORY MENU
SERVICE MENU
HISTORY MENU MOTOR GROUP
SERVICE MENU REPORT
REPORT SERVICE REPORT
REPORT
HISTORY REPORT
REPORT
CARTRIDGE
REPORT
EVENT LOG
REPORT
ALL
REPORT
SERIAL
SVC.MODE HEAT.
STOP > STOP
HEATER ADJUST
PRINT
HEATER ADJUST
DRYER
PREHEAT TEMP.
35 C 35 C
HEAT TIMEOUT
OFF 10min
Print Heater : OFF
PRINT _ 25 C
DRYER 25 C
This is for checking the heaters and thermistors.
While in this menu, it shows ON/OFF status and the temperatures read from the thermistors of Print heater and Dryer. [
are for selecting the heater or dryer and [ENTER] key is for turning ON/OFF the selected heater or dryer. "ON/OFF" mentioned here only
means to power on or off manually, and not to control the temperature. Be aware that the temperature keeps rising while it is ON. It turns off
automatically when exiting the menu.
Check if the temperature rises when the heater or dryer is ON and also if the temperature decreases to the room temperature when it is OFF.
The temperature is displayed in Celsius only.
PAGE1
00000000
bit #[ 8 7 6 5 4 3 2 1 ]
PAGE16
00000000
bit #[ 8 7 6 5 4 3 2 1 ]
MOTOR HOURS F
3 hours
In History Menu, the parameters are separated in groups
by categories. The parameters can be displayed or cleared
by selecting the group.
NUM PRINT LOGS
100 LOGS
Options: 100LOGS/200LOGS/ALL
4-8
The heater does not operate when the machine is started in Service Mode.
Set [START] here when the heater needs to be on. [START] is canceled once the
Sub Power is turned off and the setting is back to [STOP] when entering the
Service Mode next time.
PRINT
This is for setting the offset of heater temperature.
0 -3
The heater is controlled with this offset value added
to the temperature displayed on the LCD.
Range: -5 to +5
DRYER
0 -3
This is for setting the heater temperature for [PREHEATING] under the
[HEATER MENU] in the User Menu.
Range: 20 to 40 C Default: 30 C
This is for setting the time to show the confirmation message when controlling
heater temperature before printing. It shows the message of
[HEATING TIMEOUT CONTINUE?] when the temperature controll is not completed
at the specified timing when controlling the heater temperature before printing.
Range: OFF, 10 to 30 min (by 10 min)
Print Heater : ON
PRINT _ 40 C
*
DRYER 25 C
This is the software switch for switching the setting of supporting functions.
Normally, it is not necessary to change. Each bit can be selected by [
and switched by [ ] and [ ] keys.
Press [ENTER] key to save the settings. There are 16 pages of 8 bit System Switches.
Bit Contents
Reflection of the heater related [1] enables the settings of [FULL WIDTH S] and
PAGE1:Bit4
parameters to the test pattern [PERIODIC CL.] for all test patterns.
PAGE1:Bit7 Periodic flushing of MAX ink
Enables with [0], Disables with [1]
The AQUEOUS PIGMENT ink with [1].
PAGE4:Bit7 Pump Operation
ECO-SOL MAX ink with [0].
* All the default of the items not shown here is [0].
CAUTION : The machine may make unexpected move when the Bits not shown here are changed.
MOTOR HOURS F
CLEAR
CATEGORIES: MOTOR GROUP / HEAD GROUP / MAINTE GROUP /
WIPE GROUP / PRINT GROUP / CUTTING GROUP /
INK GROUP / HEATER GROUP / ERROR GROUP /
SYSTEM
Reports can be printed. The head to print the report is selectable, considering the
case of head trouble. Select a head with [
to start printing.
SERVICE : Service Report is printed. It prints the Service Information additionally
to the System Report of the standard menu.
HISTORY : History Report is printed.
CARTRIDGE : Ink Cartridge IC Report is printed. It lists the information written on
the IC of the Ink Cartridges installed on the machine.
EVENT LOG : Event Log Report is printed. The number of Event to be printed is
selectable from 100/200/ALL(400).
ALL : All Reports are printed together. (System Report, Service Report,
History Report, Ink Cartridge IC Report, Event Log Report).
SERIAL : Service Report and History Report can be sent to RS-232C Serial
using special tool. (9600bps, N81, X : ON/OFF)
Default: 0
Default: 20 min
] and [ ] keys
] and [ ] keys
Meanings Default
0
0
0
] and [ ] keys and press [ENTER] key
Required Printing Area
SERVICE: W270 L360mm
HISTORY: W165 L160mm
CARTRIDGE: W180 L35mm
EVENT LOG/100 LOGS: W280 L155mm
EVENT LOG/200 LOGS: W280 L285mm
EVENT LOG/ALL(400): W280 L545mm