Table of Contents
Advertisement
Quick Links
CCR
Model No. 38571—Serial No. 280000001 and Up
Model No. 38575—Serial No. 280000001 and Up
Introduction
Read this information carefully to learn how to operate
and maintain your product properly and to avoid injury
and product damage. You are responsible for operating
the product properly and safely.
You may contact Toro directly at www.Toro.com for
product and accessory information, help finding a
dealer, or to register your product.
Whenever you need service, genuine Toro parts, or
additional information, contact an Authorized Service
Dealer or Toro Customer Service and have the model
and serial numbers of your product ready. Figure 1
identifies the location of the model and serial numbers
on the product. Write the numbers in the space
provided.
Figure 1
1. Model and serial number location
Model No.
Serial No.
This manual identifies potential hazards and has
safety messages identified by the safety alert symbol
(Figure 2), which signals a hazard that may cause serious
injury or death if you do not follow the recommended
precautions.
© 2008—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
6053 Quick Clear™ Snowthrower
Register at www.Toro.com.
1. Safety alert symbol
This manual uses 2 words to highlight information.
Important calls attention to special mechanical
information and Note emphasizes general information
worthy of special attention.
Safety
This snowthrower meets or exceeds the ISO
standard 8437 in effect at the time of production.
Read and understand the contents of this manual
before the engine is ever started.
This is the safety alert symbol. It is used to alert
you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid
possible injury or death.
Improperly using or maintaining this snowthrower
could result in injury or death. To reduce this
potential, comply with the following safety
instructions.
Training
• Read, understand, and follow all instructions on the
machine and in the manual(s) before operating this
unit. Be thoroughly familiar with the controls and
the proper use of the equipment. Know how to stop
the unit and disengage the controls quickly.
• Never allow children to operate the equipment.
Never allow adults to operate the equipment without
proper instruction.
• Keep the area of operation clear of all persons,
particularly small children.
• Exercise caution to avoid slipping or falling.
Form No. 3358-441 Rev D
Operator's Manual
Figure 2
Original Instructions (EN)
Printed in the USA
All Rights Reserved
Advertisement
Table of Contents
Related Manuals for Toro 38571
Summary of Contents for Toro 38571
- Page 1 Whenever you need service, genuine Toro parts, or additional information, contact an Authorized Service Safety Dealer or Toro Customer Service and have the model and serial numbers of your product ready. Figure 1 This snowthrower meets or exceeds the ISO identifies the location of the model and serial numbers standard 8437 in effect at the time of production.
- Page 2 Preparation Operation • Thoroughly inspect the area where the equipment is • Do not put hands or feet near or under rotating parts. to be used and remove all doormats, sleds, boards, Keep clear of the discharge opening at all times. wires, and other foreign objects.
- Page 3 EN 3744. Toro Snowthrower Safety Vibration The following list contains safety information specific to Toro products or other safety information that you This unit does not exceed a hand/arm vibration level of must know. 12.7 m/s , based on measurements of identical machines •...
-
Page 4: Safety And Instructional Decals
6. Primer hazard, rotor blades—stop the engine before leaving the machine. 3. Thrown object 7. Push the primer three 108-4930 (Model 38571 only) hazard—keep bystanders times to prime the engine. a safe distance from the 1. Warning—read the Operator’s Manual. machine. -
Page 5: Unfolding The Handle
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. – No parts required Unfold the handle. Screws Chute assembly Install the discharge chute. Discharge chute handle 1. Unfolding the Handle Procedure 1. -
Page 6: Installing The Discharge Chute
2. Installing the Discharge • For temperatures between 0°F and 32°F (–18°C and 0°C), use SAE 5W30 or SAE 10. Chute • For temperatures below 0°F (–18°C), use SAE 0W30. Screws Chute assembly 1. Move the snowthrower to a level surface. Discharge chute handle 2. -
Page 7: Product Overview
Fill the fuel tank with fresh unleaded gasoline (Figure 9). Figure 8 8. Electric-start button 1. Chute deflector trigger Figure 9 (model 38571 only) 2. Discharge chute 9. Ignition key 1. 1/4 inch (6 mm) 3. Discharge chute handle 10. Choke lever 4. -
Page 8: Starting The Engine
2. Pull out the choke lever (Figure 12). 4. Connect an extension cord to a power source and the snowthrower, and push the electric-start button (model 38571 only) (Figure 14), or pull the recoil start handle (Figure 15). Figure 12 Figure 14 1. -
Page 9: Stopping The Engine
If the engine does not start after the second series of attempts, take the snowthrower to an Authorized Service Dealer for service (model 38571 only). 5. While the engine is running, push in the choke lever slowly. -
Page 10: Operating Tips
• With the ignition key in the Off position, pull the recoil starter handle several times or push the electric start button once (model 38571 only) to prevent the recoil and electric starters from freezing up. • In snowy and cold conditions, some controls and Figure 19 moving parts may freeze. -
Page 11: Recommended Maintenance Schedule(S)
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Maintenance Procedure Interval • Check the control cable and adjust it if necessary. After the first hour • Check for loose fasteners and tighten them if necessary. •... -
Page 12: Changing The Engine Oil
Note: You can pull up the adjuster link and cable to Before each session, inspect the rotor blades for wear. make unhooking the spring easier. When a rotor blade edge has worn down to the wear indicator hole, have an Authorized Service Dealer 2. -
Page 13: Servicing The Spark Plug
Servicing the Spark Plug Service Interval: Yearly—Service the spark plug and replace it if necessary. Use a Champion RN4C spark plug or equivalent. 1. Stop the engine and wait for all moving parts to stop. 2. Wait until the engine has fully cooled. Figure 26 1. - Page 14 8. Set the gap on the plug to 0.030 inch (0.76 mm) (Figure 31). Figure 31 1. Center electrode insulator 3. Air gap (not to scale) 2. Side electrode 9. Install the spark plug and tighten the plug securely. 10. Connect the wire to the spark plug. 11.
- Page 15 Figure 34 16. Secure the exhaust baffle using the small side screw that you previously removed (Figure 35). Figure 33 1. Tabs 13. Install the 2 screws into the exhaust baffle. 14. Return the snowthrower to the operating position. 15. Tuck the lower lip of the guard behind the belt cover (Figure 34).
-
Page 16: Replacing The Drive Belt
Replacing the Drive Belt Note: Route the new drive belt first around the engine pulley, then the idler pulley, and finally around If drive belt becomes worn, oil-soaked, excessively the loose rotor pulley positioned just above the rotor cracked, frayed, or otherwise damaged, replace the belt. shaft (Figure 36). - Page 17 Storage 14. Tighten any loose fasteners. Repair or replace any damaged parts. 15. Cover the snowthrower and store it in a clean, dry Storing the Snowthrower place out of the reach of children. Allow the engine to cool before storing it in any enclosure. •...
- Page 18 Notes:...
- Page 19 Spypros Stavrinides Limited Cyprus 357 22 434131 Surge Systems India Limited India 91 1 292299901 T-Markt Logistics Ltd Hungary 36 26 525 500 Toro Australia Australia 61 3 9580 7355 Toro Europe BVBA Belgium 32 14 562 960 374-0102 Rev B...
- Page 20 Contact your seller to arrange service of the product. If for any reason materials or workmanship. The following time periods apply from the date it is impossible for you to contact your seller, you may contact any Toro of original purchase: Authorized Distributor to arrange service.