Canon imageRUNNER 2530 Service Manual Digest page 24

Ecode Detail Item
Code
E240 0000 Title Error in controller communication
Description The serial communication error such as parity error or
overrun error is constantly detected.
Remedy 1.Check the Connectors.
2.Replace the DC Controller PCB (PCB4).
E240 0001 Title Error in controller communication
Description The serial communication error such as parity error or
overrun error is detected while printing.
Remedy 1.Check the Connectors.
2.Replace the DC Controller PCB (PCB4).
E246 0000 Title Writing to the counter PCB (FRAM) failed
Description -
Remedy -
E247 0000 Title Mismatched checksum between the Flash Rom and the
FRAM
Description -
Remedy -
E261 0000 Title Error in Zero Cross
Description Zero Cross failed to be detected for 500ms or more while the
relay was ON.
* The same condition is detected after the error retry is
performed.
Remedy 1.Check the Connectors.
2.Replace the DC Controller PCB (PCB4).
E350 0000 Title SOFT-ID PCB error
Description -
Remedy -
E354 0000 Title Mismatched serial number for the SOFT-ID PCB
Description -
Remedy -
E355 0000 Title Mismatched serial number between the SOFT-ID, the Flash
Rom and the FRAM
Description -
Remedy -
E355 0004 Title System information error
Description -
Remedy -
E355 0005 Title System information error
Description -
Remedy -
E500 0000 Title Communication error
Description The communication with the host machine is interrupted.
Remedy 1.Check the cable.
2.Replace the Finisher Controller PCB (PCB1).
3.Replace the DC Controller PCB.
Description Ecode Detail Item
Code
E505 0001 Title EEPROM error
Description The checksum for the EEPROM data has an error.
Remedy 1.Replace the Finisher Controller PCB (PCB1).
E520 0001 Title Shift Motor (M4) error
Description The shift roller does not leave the shift roller home position
when the Shift Motor (M4) has been driven for 1.2 seconds.
Remedy 1.Replace the Shift Roller HP Sensor (S2).
2.Replace the Shift Motor (M4).
3.Replace the Finisher Controller PCB (PCB1).
E520 0002 Title Shift Motor (M4) error
Description The shift roller does not return to the shift roller home position
when the Shift Motor (M4) has been driven for 1.2 seconds.
Remedy 1.Replace the Shift Roller HP Sensor (S2).
2.Replace the Shift Motor (M4).
3.Replace the Finisher Controller PCB (PCB1).
E531 8001 Title Stapler Motor (M10) error
Description The stapler does not leave the staple home position when the
Staple Motor (M10) has been driven for 0.5 sec.
Remedy 1.Check the wiring between the Finisher Controller PCB and
Stapler.
2.Replace the Stapler.
3.Replace the Finisher Controller PCB (PCB1).
E531 8002 Title Stapler Motor (M10) error
Description The stapler does not return to the staple home position when
the Stapler Motor (M10) has been driven for 0.5 sec.
Remedy 1.Check the wiring between the Finisher Controller PCB and
Stapler.
2.Replace the Stapler.
3.Replace the Finisher Controller PCB (PCB1).
E532 0001 Title STP Move Motor (M1) error
Description The stapler does not leave the stapler move home position
when the STP Move Motor (M1) has been driven for 0.25 sec.
Remedy 1.Replace the Stapler Move HP Sensor (S10).
2.Check the wiring between the Finisher Controller PCB and
the STP Move Motor.
3.Check the stapler shift base.
4.Replace the STP Move Motor (M1).
5.Replace the Finisher Controller PCB (PCB1).
Description
3
3-5