Flashforge Foto 13.3 Quick Start Manual
  1. Manuals
  2. Brands
  3. Flashforge Manuals
  4. 3D Printers
  5. Foto 13.3
  6. Quick start manual

Flashforge Foto 13.3 Quick Start Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

EN/CN-A02
1. When the glass over the LCD screen cracks, stop printing immediately, otherwise
WARNING
the crack will expand and cause more serious damage.
2. The maximum tank volume is 3 liters. Note that moderate resin must be added
so its level will be between the upper and lower marker lines in the tank.
3. The correct way to cut off power supply is to turn off the power switch of the
printer.
4. Do not cut off the power abruptly during printing to avoid mechanical damage.
This guide is only applicable to FLASHFORGE Foto 13.3 3D printer
Foto 13.3

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Foto 13.3 and is the answer not in the manual?

Questions and answers

Related Manuals for Flashforge Foto 13.3

Summary of Contents for Flashforge Foto 13.3

  • Page 1 3. The correct way to cut off power supply is to turn off the power switch of the printer. 4. Do not cut off the power abruptly during printing to avoid mechanical damage. This guide is only applicable to FLASHFORGE Foto 13.3 3D printer...
  • Page 2 NOTE Three screws A, B and C indicated in the picture should not be loosened, otherwise the printing will fail!
  • Page 3 Flashforge Technology are excellent. For your convenience, please read the manual carefully before use, and strictly follow the instructions of the manual. The entire Flashforge Technology team is always ready to provide you with the best quality service. No matter what problems you encounter during use, please contact us according to the telephone and email provided at the end of the manual.
  • Page 4 Do not abuse the power cord, and be sure to use the power cord provided by Flashforge. Do not use the device during thunderstorms. If you do not use the device for a long time, please turn off...
  • Page 5 Getting To Know Your 3D Printer 1. Z-axis 2. Platform Tighten Knob 3. Leveller 4. Build Plate 5. Light Shield 6. LCD 7. Box Tighten Knob 8. Resin Box 9. Touched Screen 10. Ethernet 11.USB Stick Port 12. Power Switch 13.

  • Page 6: Accessory Box

    Accessory Box 3D Printer Resin Power Cable Quick Start Guide After-sales Service Metal Scraper Plastic Scraper Brush Rubber Glove USB Stick Wrench Tweezers Accessory Kit Soft Cloth Filter Diagonal Pliers...
  • Page 7 Unpacking 1. Cut the tie to open the box. 2. Take out the top foam. 3. Lift up and remove the outer box. 4. Remove the foam on both sides. 5. Open the front door of the device and 6. Loosen the platform fastening knob. prepare to take out the foam inside.
  • Page 8 7. Take out the molded platform. 8. Remove the foam. Note that there is a bottle of resin and a tool box inside the foam cotton. 9. Complete.
  • Page 9 Leveling 1. Confirm that the printing platform is clean. Install the platform as shown in the picture: fit it on the Z-axis and fasten it with hand-screw nuts.Confirm that there is no misalignment in the installation of the platform and that it is not loose when moved manually.
  • Page 10 3. Connect the power cable to theadapter, insert the outputof the power adapter into the power inlet port on the back of the printer. Turn on the switch. Print Tool System Move Residue WLAN Stop 4. Place 3 sheets of A4 paper over the 5.
  • Page 11 Stop No.2 No.4 No.3 Tighten No.1 6. Click on [Reset] to reset the Z-axis and lower the platform to the zeroposition. When the platform is lowered to the bottom, tighten the four M6 screws No.1-4 in sequence according to the figures shown. Stop 7.

  • Page 12: First Printing

    First Printing 1. Confirm that the LCD screen and resin box are clean. 2. Take out the resin box and place it carefully on the screen. Pay attention to the orientation of the pouring port and install it in the direction shown on the right.
  • Page 13 No misalignment and looseness in installation Clean 4. Confirm that LCD screen, build plate and solution box are clean. 5. Make sure that the resin box and platform are installed in alignment and that they are not loose when moved by hand. 6.
  • Page 14 File list Model-01 Model-02 Print Tool System Model-03 Model-04 Model-01 1000 3 h 49 min 0.05 mm 9. Click [Print] to enter the model list. Click the model file to start printing.

  • Page 15: Post-Processing

    Post-processing 1. When the printing is finished, a notification will be displayed.Click [OK], open the light shield, take out the build plate, drain the remaining resin, and shovel the model off with a scraper. Note: There will be uncured resin on the model when printing is just finished.
  • Page 16 Replace the FEP film in the resin box 1. Loosen the screws indicated in the picture and take out the resin box. Remove the remaining resin and clean the box. 2. Turn the box up side down and loosen 3. Clean the bottom of the resin box and the screws on the base.
  • Page 17 6. Tighten the M4*12 countersunk screws from 1 to 10. Please do it in a diagonal order. 7. Cut off excess FEP membrane (dark part) to finish the replacement. Please double check if the resin box is polluted with dirt, fingerprints, etc. If so, it needs to be cleaned again.

  • Page 18: Software Operation

    Software Operation FlashDLPrint FlashDLPrint.exe Load Supports Print 2. Click Load, select the model file. 1. Install and run the FlashDlprint.exe program. Print Set Position View I want to: Preview Print When Slice Done 0.00mm Material Type: Grey Standard 0.00mm Save As New Remove Operation: 0.00mm...
  • Page 19 CHITUBOX CHITUBOX V1.8.1 Open Project 1. Install and turn on the ChiTuBox64.exe Save ProJect program. Open... Save As... 2. Click the【Open...】in the menu at the upper left corner to select the model files. untitled* CHITUBOX V1.8.1 File List Select All Solid X-Ray 0.00...
  • Page 20 Settings FLASHFORGE Standard Resin Grey for 0.1mm Default Machine Resin Print Gcode Advanced foto 13.3 Layer Height： Bottom Lift Distance： foto 8.9 Bottom Layer Count： Lifting Distance： foto 6.0 Exposure Time： Bottom Lift Speed： mm/min Exposure Time： Lifting Speed： Linear mm/min Retract Speed：...

  • Page 21: Maintenance

    Maintenance Please keep two parts shown in the picture below clear without dust and fingerprint. Do not pour the used residual resin back to the resin bottle. The waste resin can be poured into the sealing bag for sealing and then be exposed to the sun until the resin solidifies.
  • Page 22 Follow us Zhejiang Flashforge 3D Technology Co., Ltd. Address: No.518 XianYuan Road, Jinhua City,Zhejiang Province, China Service Hotline: +86 579 82273989 support@flashforge.com...
  • Page 23 FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Table of Contents