Advertisement
Advertisement
Related Manuals for Erbauer EHP1050
Summary of Contents for Erbauer EHP1050
- Page 1 EAN 3663602796442 EHP1050 ORIGINAL INSTRUCTIONS V60823 BX220IM...
-
Page 2: Table Of Contents
Safety instructions Product description Assembly Care & maintenance Guarantee Declaration of conformity... - Page 3 WARNING! Please read all safety warnings carefully and be sure that they are fully understood before handling the tool.
- Page 4 Product description...
-
Page 7: Safety Instructions
Safety instructions GENERAL POWER TOOL SAFETY WARNING WARNING Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool”... - Page 8 b) Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. c) Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool.
- Page 9 5) SERVICE a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. SAFETY WARNINGS FOR PLANERS a) Wait for the cutter to stop before setting the tool down. An exposed rotating cutter may engage the surface leading to possible loss of control and serious injury.
- Page 10 ADDITIONAL SAFETY WARNINGS FOR CONSTRUCTION DUST The updated Control of Substances Hazardous to Health Regulations 1st October 2012 now also targets to reduce the risks associated with silica, wood and gypsum dusts. Construction workers are one of the at-risk groups within this because of the dust that they breathe: silica dust is not just a nuisance;...
- Page 11 WARNING! Some dust particles created by power sanding, sawing, grinding, drill and other construction jobs contain chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints. • Crystalline silica from bricks and cement and other masonry products. •...
- Page 12 WARNING! The vibration emission during actual use of the power tool can differ from the declared total value depending on the ways in which the tool is used: • How the materials are grinded, cut or drilled. • If the tool is in good condition and well maintained. •...
- Page 13 VIBRATION AND NOISE REDUCTION To reduce the impact of noise and vibration emission, limit the time of operation, use low-vibration and low-noise operating modes as well as wear personal protective equipment. Take the following points into account to minimise the vibration and noise exposure risks: 1.
-
Page 14: Product Description
Product description Part index The index below refers to Fig. 1 on page 4. Rebate depth gauge 16. Wrench a. Scale (in Fig. D) 17. Hex bolts (×3) Locking lever 18. Blade Depth scale 19. Grub screws (×2) Cutting depth adjustment knob 20. - Page 15 dB(A) Decibel (A-rated) No-load speed To reduce the risk of injury, user must read instruction manual. Switch the product off and disconnect it from the power supply before assembly, cleaning, adjustments, maintenance, storage and transportation. This product is of protection class II. That means it is equipped with enhanced or double insulation.
- Page 16 Rating label explanation EHP1050 = Model number E = Erbauer HP = Planer 1050 = Power (Watts)
-
Page 17: Assembly
Assembly Unpacking 1. Unpack all parts and lay them on a flat, stable surface. 2. Remove all packing materials and shipping devices, if applicable. 3. Make sure the delivery contents are complete and free of any damage. If you find that parts are missing or show damage do not use the product but contact your dealer. - Page 18 Dust extraction (Fig. A and B) WARNING! Always attach a dust extraction device or the dust bag when using this product to keep the working area clean! Wear a dust mask when operating this product! Dust can be harmful to health! Especially dust and chips of wood that has been treated, e.g.
- Page 19 Parallel guide (Fig. C) Attach the parallel guide to perform straight planing cuts along a workpiece edge. 1. Align the hole in the angle bracket (24b) to the mounting thread (10) and fix it with a wing screw (24a) (Fig. C, Step 1). 2.
-
Page 20: Use
Intended use This product is intended for planing of firmly supported wooden materials, such as beams and boards. It is also suitable for bevelling edges. The product must be used in an upright position only with the front plate lying flat on the workpiece. - Page 21 Operation General cutting (Fig. G) WARNING! During operation fine dust will be generated! These dusts are highly inflammable and explosive! Do not smoke during operation, keep heat sources and open flames out of the working area! Always wear a dust mask to protect yourself against hazards resulting from fine dust! 1.
- Page 22 Bevel planing (Fig. H) With the V-groove (14) bevel angles of 45° can be cut on the edge of a workpiece. 1. Place the V-groove (14) onto the edge of the workpiece. Apply slight consistent pressure against the workpiece to achieve an even result. 2.
-
Page 23: Care & Maintenance
Care & maintenance WARNING! Always switch the product off, disconnect the product from the power supply and let the product cool down before performing inspection, maintenance and cleaning work! Only perform care and maintenance work according to these instructions! All further works must be performed by a qualified specialist! Clean •... - Page 24 Blade changing (Fig. K and L) 1. Lay the product on a flat surface so that you have free access to the bottom side. 2. Turn the roller (20) until the blade shaft is positioned between the front and rear plates (13 and 12).
- Page 25 UK plug (only for UK market) Replacement of the plug shall always be carried out by the manufacturer of the tool or his service organization and follow the instructions below. IMPORTANT: The wires in the mains lead are coloured in accordance with the following code: Blue –...
- Page 26 Transportation WARNING! Always carry the product by its main handle. Never use the cord for carrying the product. 1. Switch the product off and disconnect it from the power supply. 2. Protect the product from any heavy impact or strong vibrations which may occur during transportation in vehicles.
-
Page 27: Guarantee
Guarantee At Erbauer we take special care to select high quality materials and use manufacturing techniques that allow us to create ranges of products incorporating design and durability. We carry out stringent testing procedures on all our tools and are confident that they can provide regular, sustained daily use during the period covered. -
Page 28: Declaration Of Conformity
3 Sheldon Square London W2 6PX United Kingdom Declare that the product: Erbauer 1050W Planer EHP1050 Serial number：000001 - 999999 Complies with the essential health and safety requirements of the following directives: 2006/42/EC The Machinery Directive References to the following harmonized standard were made:... - Page 29 Kingfisher International Products B.V. Rapenburgerstraat 175E 1011 VM Amsterdam The Netherlands Declare that the product: Erbauer 1050W Planer EHP1050 Serial number：000001 - 999999 Complies with the essential health and safety requirements of the following directives: 2006/42/EC The Machinery Directive References to the following harmonized standard were made:...
- Page 30 Manufacturer • Fabricant • Producent • Producator • Fabricante: Kingfisher International Products Limited, 3 Sheldon Square, London, W2 6PX, United Kingdom www.kingfisher.com/products Kingfisher International Products B.V. Rapenburgerstraat 175E 1011 VM Amsterdam The Netherlands www.diy.com www.screwfix.com www.screwfix.ie To view instruction manuals online, visit www.kingfisher.com/products...
Need help?
Do you have a question about the EHP1050 and is the answer not in the manual?
Questions and answers