Advertisement
1.3.
BATTERY SAFETY PRECAUTIONS
WARNING! Battery contains Lithium-ion which is dangerous. Handle with care to avoid damage, fire, corrosion or personal injury.
‰
Charge battery prior to its first use. The battery will have been shipped in a low charge state. To reduce the risk of burns or fire:
9
DO NOT Attempt to open, disassemble, modify or service the battery pack.
8
DO NOT Crush, puncture, short external contacts or dispose of in fire or water.
8
DO NOT Expose to temperatures above 40°C (104°F).
8
Replace only with the battery pack designated for this product.
9
Use only the supplied charging base provided to charge the battery.
9
DO NOT attempt recharging the battery by means of an engine generator or a DC power source.
8
WARNING! Dispose of spent batteries correctly as they contain Lithium-ion. DANGER! DO NOT attempt to disassemble the
‰
battery. For safety and environmental reasons DO NOT discard in domestic waste or by burning. ONLY discard or recycle
according to local authority regulations.
WARNING! DO NOT allow a leaking battery to contact your person.
‰
1.4.
GENERAL SAFETY
Maintain the tool and battery in good condition. Check moving parts alignment on a regular basis.
9
Replace or repair damaged parts. Use an authorised service agent and recommended parts only. Unauthorised parts may be
9
dangerous and will invalidate the warranty.
Ensure the tool is switched off before installing the battery pack.
9
Keep the tool and charger clean for best and safest performance.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
9
Evaluate your working area before using the tool; e.g. ceilings, floors and enclosures may contain electrical items or water piping.
9
Ensure battery pack is correctly inserted into the handle and latched in place before attempting to switch on tool.
9
Secure loose work pieces with a clamp, vice or other adequate holding device.
9
Avoid unintentional starting.
9
Wear approved safety eye protection (standard spectacles are not adequate).
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-skid shoes.
9
Keep direction switch in the locked position until the tool is required for use.
9
Keep children and unauthorised persons away from the working area.
9
DO NOT use the tool where there are flammable liquids, solids or gases, such as paint solvents, etc.
8
DO NOT allow children to operate the tool.
8
DO NOT operate the tool if any parts are missing as this may cause failure and/or personal injury.
8
DO NOT hold unsecured work piece in your hand.
8
DO NOT leave the tool operating unattended.
8
DO NOT carry the tool with your finger on the power switch. Keep chuck direction switch in the locked position.
8
DO NOT use the tool for a task it is not designed to perform.
8
DO NOT operate the tool when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT get the tool or battery charger wet or use in damp or wet locations.
8
2. INTRODUCTION
Compact, lightweight cordless 1/4"Hex drive impact driver. Comfortable housing with soft grip to reduce vibration. Variable speed gives
more control during application. Integrated LED battery level indicator and LED work light. Supplied with 1 hour mains charger and 1 x 2Ah
rechargeable Lithium-ion battery.
3. SPECIFICATION
Model no .............................................................CP108VCID
Battery ............................... 10.8V 2Ah Lithium-ion (Included)
Consumable parts .............................CP108VBP 2Ah Battery
Drive ......................................................................... 1/4" hex
Impact rate ......................................................... 0-40500bpm
Max. torque .................................................................120Nm
Noise power/pressure .................................... 84.2/73.2dB(A)
No-load speed .......................................................0-2700rpm
Replacement parts .....................CP108VMC - mains charger
Vibration/uncertainty .......................................... 0.57/1.5m/s²
4. BATTERY CHARGING
4.1.
Fully charge the battery before first use.
WARNING! Only recharge batteries with the charger supplied.
‰
4.2.
Remove battery by squeezing buttons in on each side.
Insert into battery charger.
4.3.
Connect charger to mains supply and red LED will light to signal charging. Once charging is complete LED turns green.
4.4.
Remove from mains supply, remove battery and insert into tool until a click is heard.
4.5.
BATTERY CHARGE STATUS TEST
4.5.1.
Press trigger, all LEDs lit: battery charged, one LED lit: battery needs charging.
4.6.
In order to maintain battery efficiency:
DO NOT fully discharge. After every use fully charge the battery, charge every 4 months even if tool is not used.
If a decrease of performance of the tool is noticed, charge the battery.
© Jack Sealey Limited
Original Language Version
CP108VCID Issue:1 24/02/21
Advertisement
