Sealey CP108VMTBO Quick Start Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instruction protection
manual
1. SAFETY
1.1. GENERAL SAFETY
WARNING! Disconnect the multi-tool from the battery unit before changing accessories, servicing, storing or performing any
‰
maintenance.
Maintain the multi-tool and battery in good condition. Check moving parts alignment on a regular basis.
9
Replace or repair damaged parts. Use an authorised service agent and recommended parts only. Unauthorised parts may be
9
dangerous and will invalidate the warranty.
Ensure the multi-tool is switched off before installing the battery pack or picking up the tool.
9
Remove any adjusting key or wrench before turning the tool on.
9
Keep the multi-tool and charger clean for best and safest performance.
9
Keep working area well lit.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
9
Evaluate your working area before using the multi-tool e.g. ceilings, floors and enclosures may contain electrical items or water piping.
9
Ensure battery pack is correctly inserted into the tool handle and latched in place before attempting to switch it on.
9
Secure loose work pieces with a clamp, vice or other adequate holding device.
9
Avoid unintentional starting.
9
Wear approved safety eye and ear protection (standard spectacles are not adequate). Wear a mask.
9
DO NOT over reach. Maintain correct balance and footing. Ensure the floor is not slippery and wear non-skid shoes.
8
DO NOT let familiarity from frequent use of tool allow you to become complacent and ignore tool safety principles.
8
Keep children and unauthorised persons away from the working area.
9
Keep tool and charger in the case and store in a safe, dry, childproof area where the temperature will not exceed 104°F (40°C).
9
DO NOT use the tool where there are flammable liquids, solids or gases, such as paint solvents, etc.
8
DO NOT allow children to operate the tool. DO NOT allow persons unfamiliar with the tool or these instructions to operate the tool.
8
DO NOT operate the tool if any parts are missing as this may cause failure and/or personal injury.
8
DO NOT hold unsecured work piece in your hand.
8
DO NOT leave the tool operating unattended.
8
DO NOT carry the tool with your finger on the power switch.
8
DO NOT use the tool for a task it is not designed to perform.
8
DO NOT force the tool. Use the correct tool for your application. The correct power tool will do the job better and safer and at the rate
8
for which it was designed.
Use the power tool in accordance with these instructions, taking into account the working conditions and the work to be performed.
9
Use of the tool for operations different from those intended could result in a hazardous situation.
Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for
9
safe handling and control of the tool in unexpected situations.
DO NOT use the tool if the switch does not turn it off and on. Any power tool that cannot be controlled with the switch is dangerous and
8
must be repaired.
DO NOT operate the tool when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT get the tool or battery charger wet or use in damp or wet locations.
8
2. INTRODUCTION
i
Part of the SV10.8 Series offering a one battery fits all solution, keeping costs down without compromising on performance. Compact,
lightweight cordless Multi-Tool - Body Only. Comfortable housing with soft grip to help reduce vibration. One tool suitable for multiple
tasks such as sanding, scraping and cutting various materials. Includes sanding paper, backing pad, scraper and cutting blade. 6-Speed
settings for greater control. Quick release/lock system for fitting attachments. Requires compatible 10.8V 2Ah or 4Ah battery and mains
charger, sold separately.
© Jack Sealey Limited
10.8V SV10.8 SERIES MULTI-TOOL - BODY
ONLY
MODEL NO:
Wear a Wear ear Wear protective
mask protection
Original Language Version
CP108VMTBO
gloves
CP108VMTBO Issue 1 02/12/22