Line Magnetic MINI 218IA Quick Start Manual page 2

Functions Description
Front Panel:
3.Headphone Socket
4.Selector: Output selection between Speaker and Headphone.
Side Panel:
Rear Panel:
Outputs: used to
connect with the
speakers.
Signal Input:
used for source input.
Connection
Speaker Connection
Check the impedance of your speakers. Attach the positive from your
speaker to the 4, or 8 ohm terminals and the negative to the 0 ohm
terminals separately. 4 ohm or 8 ohm impedance speakers are
preferential and if your speakers are 6 ohm it would not cause damage
to the amplifier and experience using 4, or 8 ohm positive terminal to
find what the best is for your speakers. Please take the right
guidance for connection and do not mix as wrong connection may cause
noise or low grade function.
Note:
Connect the speaker cables with the amplifier after it is well connected
with the speakers. Please notice the right direction indication of the cable
and do not mix up the positive and the negative end.
1.Volume Knob: Volume
up to the right while
volume down to the left.
2.Indicator for Operation
ON/OFF:
Turn on or turn off the amplifier.
Power Socket with main
fuse: Main fuse is located
on the rear of the amplifier
just below the power cord
socket. Replace with the
same type and value fuse.
How to connect the speaker cables:
1.Unscrew the terminal knobs,
2.Insert the speaker cables,
3.Screw the terminal knobs.
Audio Connection
Here is the standard way of connection for MINI 218IA with other audio
equipments. Please take pictures below for your reference:
Suggestions:
1.During installation please always refer to other products' operation
manuals.
2.Please do not insert the power cord into the main socket only if all
other instruments are well connected.
3.R refers to right channel while L represents left channel.
4.Please take the right guidance for connection as wrong connection may
cause noise or low grade function.
5.Do not fasten signal cables together with other cables just like the
power cables to avoid disturbance.
Warranty Statement
Terms & Conditions:
1. Limited Warranty: One-year limited warranty from the date of purchase except
vacuum tubes which are warranted for six months.
2. Limited to original purchaser. This warranty is for the sole benefit of the
original purchaser of the covered product, and may not be transferred to a
subsequent owner.
3. Conditions & Limitations. This warranty is subject to conditions and limitations,
as follows. This warranty is void and inapplicable if the product has not been
used or handled other than in accordance with the instructions in the owner's
manual, or if it has been misused, abused, damaged by accident or neglect, or
in transport once in possession of purchaser, or the defect is due to the
product being repaired or tampered with by anyone other than Zhuhai Line
Magnetic Audio Co., LTD or an authorized Line Magnetic Audio Representative.
4. Remedy: If the product contains material, or manufacturing defects, it must be
packed in original packaging and returned to Zhuhai Line Magnetic Audio Co.,
LTD or an authorized Line Magnetic Audio Representative at his or her sole
expense. A returned product must be accompanied by a written description of
the defect and the warranty card with an authorized dealer's stamp on which
indicates the model and series number, the date of purchase, the name and
address of the purchaser. Zhuhai Line Magnetic Audio Co., LTD reserves the
right to modify the design of the product and change the specifications without
notice or obligation to any person.
5. Miscellaneous. Any implied warranties relating to the above product shall be
limited to duration of this warranty. This warranty does not extend to any
incidental or consequential costs or damages to purchaser. Our liability will be
no more than the amount you paid for the product that is the subject of a
claim. This is the maximum amount for which we are responsible. This warranty
gives you specific legal rights. You may also have other rights which vary from
country to country, state to state.
Troubleshooting
Please follow the instruction in the manual in order to keep the amplifier work
in its best state. If wrongly operated and you thought that would be troubles
please check according to following tips to look for the exact reason.
Sometimes problems would be caused by the other related products and please
have a check too on those connections. Even doing so, if the problem still
exists please contact with your local agent or our company.
Problem
Power cord is not
well-connected
Power LED
Main fuse is out.
is OFF.
Troubles of inner parts
or components.
Volume is at ZERO.
Power LED
is ON.
NO signal input.
Sound Distortion High input signal level.
Ground of input signal cable
Noise output
is open or bad contact of
the input signal cable.
Components or circuits
are in trouble.
Sound field Signal input cables or
Positioning is speaker cables are
not so good. wrongly connected.
Line Magnetic logo is registered trademark of Zhuhai Line
Magnetic Audio Co., LTD. Copyright of Zhuhai Line Magnetic
Audio Co., LTD. All Rights Reserved.
Cause Remedy
Please check the power cable
connection or power outlet connection
Replace with the same type and value fuse.
Please contact with local agents or
our company.
Turn up the Volume.
Check the function of the sound source.
Check the input selection and switch to
the proper input.
Turn down the volume to suitable position.
Replace the input signal cable with a
new one.
Please contact with local agents or
our company.
Reconnect it as suggested in the manual.