Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Line Magnetic LM-219IA
Summary of Contents for Line Magnetic LM-219IA
- Page 1 INTEGRATED VACUUM TUBE AMPLIFIER LM-219IA...
-
Page 2: Table Of Contents
Table of Contents Thanks for choosing our Line Magnetic LM-219IA Integrated Amplifier as an important part of your music system. Please read this manual carefully before installation and operation. In order to prevent damage during transportation, the amplifier and its tubes are packed with... -
Page 3: Package Contents
Package Contents Please check the cartonbox carefully for any damage before opening it. 1. Line Magnetic LM-219IA 1 2. Main Fuses 2 3. Power cord 1 4. Remote control 1 5. 1.5V Batteries(AAA) 2 6. User’s Manual 1 7. Warranty Card 1 Note:All other parts except above are not included. -
Page 4: Specification
Storage Condition: Temperature: -20℃～70℃ Moisture: 20%～90% Note : Line Magnetic Audio reserves the right to change specifications at any time without further notice in advance if products are upgraded. Specifications on the manual only show the specifications of the amplifier you bought. -
Page 5: Connection
Safety precautions CAUTION RISK OF ELECTRONIC SHOCK DO NOT OPEN .To reduce the risk of electric shock, do not remove the cover. .No user serviceable parts inside. Refer servicing to qualified service personnel. .To reduce the risk of fire or electronic shock, do not expose the unit to rain or moisture. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert users to the presence of uninsulated “dangerous voltage”... - Page 6 Connection Speaker Connection Check the impedance of your speakers. Attach the positive (+) side of you speakercable to the 4, 8 or16 Ohm terminal and the negative (-) side to the 0 Ohm terminal. If your speakers are 6 Ohm or otherplease experiment with the 4,8 or 16 Ohm terminal to get the best result from your speakers.
-
Page 7: Functions Description
Functions Description Overview from the top BIAS ADJ V3 V4 BIAS ADJ V4 HUM BALANCER HUM BALANCER V3 V2 BIAS ADJ BIAS ADJ V1 V2 HUM BALANCER HUM BALANCER V1 V1, V2: 845 Power Tube V3, V4: 300B Driver Tube V5, V6: 310A Driver Tube V7, V8: 12AX7 Input Tube Bias Adjustment/Hum Adjustment: Bias Adjustment for V1, V2, V3, V4: Turn on the amplifier and wait for 10 minutes. - Page 8 Functions Description Bias current adjustments for V2, V3 and V4 are the same as V1. Please adjust to the correct bias level and make sure they are the same.for V1-V2 and V3-V4.Hum Adjustment : If hum arises , please adjust the V1 and V3 hum adjustment for the left channel and V2 and V4 for the right channel.
-
Page 9: Turning On
Functions Description Rear Panel: power socket signal mputs fuse power phase selector Make sure the powercord is disconnected before use ! Right Channel output Left Channel output Power fase selector : Lets you change the fase of the power socket .Make sure the powercord is disconnected ! Power socket with fuse : The main fuse is located on the rear panel , just below the power cord socket. -
Page 10: Remote Control
Remote Control Description Volume Mute VOLUME UP/VOLUME DOWN MUTE REMOTE CONTROL UNIT LM-02 Installation and replacement of the batteries: Installation: 1. Remove the screws of the remotes backcover. 2. Insert two AAA batteries , please check the indicators giving for the correct positioning. 3. -
Page 11: Tube Replacement
Zhuhai Line Magnetic Audio Co., LTD or an authorized Line Magnetic Audio Representative. -
Page 12: Troubleshooting
NO reaction to the remote Obstacle is located between the Remove the obstacle remote and the amplifier Line Magnetic logo is registered trademark of Zhuhai Line Magnetic Audio Co., LTD. Copyright of Zhuhai Line Magnetic Audio Co., LTD. All Rights Reserved.
Need help?
Do you have a question about the LM-219IA and is the answer not in the manual?
Questions and answers