Table of Contents
Advertisement
Available languages
Available languages
TROUBLESHOOTING GUIDE
Some tests will require accessing components. See Figures 7 & 8, page 19, for component locations. For detailed troubleshooting
procedures, refer to "Troubleshooting Tests" beginning on page 12.
PROBLEM
WON'T POWER UP
• No operation
• No Status LEDs
WON'T START CYCLE
No response when
Start Button is pressed.
UI WON'T ACCEPT
SELECTIONS
WON'T FILL
OVERFILLS
WON'T AGITATE
WON'T SPIN
PAGE 10
FOR SERVICE TECHNICIAN'S USE ONLY
NOTE: Always check for error codes first (pgs. 6–7).
POSSIBLE CAUSE
No power to washer.
Connection problem between AC plug
and main control.
Main control not properly installed
in console.
Main control problem.
Lid lock mechanism not functioning.
User Interface problem.
Main control problem.
User Interface problem.
Main control problem.
No water supplied to washer.
Plugged filter/screen.
Drain hose installation.
Valve problem.
Main control problem.
Pressure hose.
Valve problem.
Washer requires calibration.
Onboard pressure transducer.
Main control problem.
Water covering impeller?
Is lid lock showing open during the cycle?
Drive belt.
Harness connections.
Shifter problem.
Motor or motor relay problem.
Tachometer problem.
Main control problem.
Is lid lock showing open during the cycle?
Drive belt.
Harness connections.
Shifter problem.
Motor or motor relay problem.
Tachometer problem.
Main control problem.
CHECKS & TESTS
Check power at outlet, check circuit
breakers, fuses, or junction box connections.
Check the AC power cord for continuity.
See TEST #4: Console and Indicators, page 16.
See TEST #1: Main Control, page 12.
1. Lid not closed due to interference.
2. Lock not closed due to interference.
3. See TEST #8: Lid Lock, page 18.
See TEST #4: Console and Indicators, page 16.
See TEST #1: Main Control, page 12.
See TEST #4: Console and Indicators, page 16.
See TEST #1: Main Control, page 12.
1. Check water connections to washer.
2. Verify hot and cold water supply is on.
Check for plugged filter or screen in the water
valve or hoses.
Check for proper drain hose installation.
See TEST #2: Valves, page 13.
See TEST #1: Main Control, page 12.
See TEST #6: Water Level, page 17.
See TEST #2: Valves, page 13.
Perform washer calibration on page 4.
See TEST #6: Water Level, page 17.
See TEST #1: Main Control, page 12.
See TEST #6: Water Level, page 17.
See TEST #8: Lid Lock, page 18.
Verify that drive belt is not damaged.
Check harness connections between main
control and drive system.
See TEST #3a: Drive System – Shifter, page 13.
See TEST #3b: Drive System – Motor, page 14.
No tub movement or tub speed out of normal
range (obstruction/belt/motor).
See TEST #1: Main Control, page 12.
See TEST #8: Lid Lock, page 18.
Verify that drive belt is not damaged.
Check harness connections between main
control and drive system.
See TEST #3a: Drive System – Shifter, page 13.
See TEST #3b: Drive System – Motor, page 14.
No tub movement or tub speed out of normal
range (obstruction/belt/motor).
See TEST #1: Main Control, page 12.
DO NOT REMOVE OR DESTROY
Hide quick links:
Advertisement
Chapters
Table of Contents
Troubleshooting
Need help?
Do you have a question about the CAE2745 and is the answer not in the manual?
Questions and answers
How is the warranty on parts handled? Repairman says control board is defective. How **** I reimbursed? cae2745fq0 is under warranty for another 12mos
How is the warranty on parts handled? Repairman says control board is defective. How **** I reimbursed? cae2745fq0 is under warranty for another 12mos
Reset does not work
To reset the Whirlpool CAE2745 washer, follow these steps:
1. Place the program selector knob in the 12 o’clock position and wait 3–4 seconds.
2. Turn the selector knob one click counterclockwise.
3. Turn the selector knob one click clockwise.
This process should reset the washer.
This answer is automatically generated
reset does not work
To reset the Whirlpool CAE2745 washer, follow these steps:
1. Unplug the Washer – Disconnect the washer from power by unplugging it or turning off the circuit breaker.
2. Wait for a Few Minutes – Leave the washer unplugged for at least 5 minutes to allow the control board to reset.
3. Reconnect Power – Plug the washer back in or turn the circuit breaker back on.
4. Run a Calibration Cycle – If needed, enter Calibration Mode (refer to the manual) to ensure proper function.
5. Perform a Quick Test – Start a cycle to confirm that the washer is functioning correctly.
If the issue persists, refer to the diagnostic modes or check for error codes.
This answer is automatically generated