Page 3
User manual LAM1110 Dear Customer, Congratulations on your choice of hob. The user manual will help you use your product quickly and safely. • Please read this user manual before installing and using the hob. • Always follow the safety instructions.
LAMONA Appliances Index 01 - Before Using the hob 02 - Safety General Fire safety advice If a pan catches fi re Deep fat frying Safety working with gas What to do if you smell gas 03 - Using the hob...
User manual LAM1110 01 - Before using the hob • Make sure that you have removed all packaging, wrappings, stickers and fi lms from the hob surface. • It is recommended that you clean and wash the hob surface before using for the fi rst time (see p12).
LAMONA Appliances • Never leave pans over- • Never leave pans over- • Never use pans smaller • Never use pans smaller hanging the edge of the hob. hanging the edge of the hob. than 100mm (4”) and larger than 100mm (4”) and larger than 250mm (10”).Match the...
User manual LAM1110 attention shall be given to the attention shall be given to the • If you have put the fire out, • If you have put the fire out, relevant requirements regard- relevant requirements regard- leave the pan to cool com- leave the pan to cool com- ing ventilation.
LAMONA Appliances clamps etc should be checked clamps etc should be checked regularly. regularly. • Request information about • Request information about gas emergency telephone gas emergency telephone numbers and safety measures numbers and safety measures in case of gas smell from you in case of gas smell from you local gas provider.
User manual LAM1110 03 - Using the hob Hob layout Pan support Auxiliary burner Assembly Clamp Control Panel Base cover Normal burner Main body Rapid burner Normal burner Burner Controls Position Rapid burner Auxiliary burner Normal burner Normal burner Rear left...
Page 10
LAMONA Appliances Cooking with gas WARNING! Pots must not enter the control The size of the pan and the size of the gas fl ame zone. should match each other. Adjust the gas fl ames so that they do not go beyond the bottom of the pan...
User manual LAM1110 In case of fl ame failures of the burners for any reason, the fl ame failure sensor ‘A’ will cut off the gas fl ow after a few seconds. If this occurs, depress and turn the control knob to the ignition position clockwise direction and wait for ignition.
LAMONA Appliances 04 - Cleaning & maintenance How to clean your hob • Switch plates off and let cool. If necessary, • Do not use steam cleaners or high pressure treat plates with a cleaning agent (cleaner/ cleaning equipment. conditioner available in selected stores).
User manual LAM1110 Protecting the Hob cut-out Positioning The types of chipboard used for work surfaces swell relatively quickly in contact with humidity. The hob is designed to be built into a worktop as detailed in the image above. Apply a special varnish or adhesive to the cut edges to seal and protect it from moisture ingress.
LAMONA Appliances Clearances and Dimensions ** Minimum distance between cabinets must be equal to overall width of all hobs * Minimum height to extractor as recommended in extractor instruction manual No shelf or overhang of combustible material should be closer than 650mm directly above the hob.
User manual LAM1110 Secure the hob to the worktop by means of the brackets provided, taking the thickness of the worktop into account. Your appliance will be supplied and installed using the following installation method. The two brackets are secured directly into the base of the hob in appropriate positions as shown.
LAMONA Appliances Installation above a kitchen unit with door & drawer Worktop 15mm The panel installed below the hob must be easy to remove and let an easy access in case a technical assistance intervention is necessary. oven or partition...
User manual LAM1110 Adapting the hob to different types of gas To adapt the Hob for use with different types of gas, carry out the following instructions: • Remove the grids and burners • Insert on hexagonal spanner (7mm) into the...
LAMONA Appliances Regulating the minimum fl ame After lighting the burners, turn the control knob to the minimum setting then remove the knob (this can easily be removed by applying gentle pressure). Using a small «terminal» type screwdriver the regulating screw can be adjusted as in image below.
User manual LAM1110 Electrical Connections IMPORTANT: Ensure that the electricity supply is switched off before connecting. Your hob is intended for permanent installation. Your appliance must be connected to fi xed wiring via the use of a double pole switched fused spur outlet with at least 3mm contact separation.
LAMONA Appliances Technical Specifi cations General Gas Power / Category 7.4 kW / II 2H3+ G 20/20 mbar (natural gas) 704 lt/h G 30/28-30 mbar (LPG) 538 g/h Installation Class Voltage/ Frequency V / Hz 220-240 V / 50Hz Electrical Input Power...
User manual LAM1110 Troubleshooting Problem Possible Cause Remedy There is no spark when lighting • There is no electrical supply • Make sure that the unit is the gas connected and the eletrical supply is switched on. • Control the fuse. If the fuse...
Call the Depot number on your Proof of Purchase Document supplied with the product / kitchen. Call the LAMONA Service Line on 0845 00 60 006 * Product installed within a domestic kitchen or non-domestic kitchen where 8 or fewer people are using the appliance.
Page 24
Product serial number (Place sticker here) Issue v1 200117 185.9272.70/R.AA/20.01.2017...
Need help?
Do you have a question about the LAM1110 and is the answer not in the manual?
Questions and answers