Page 1
Form No. 3446-717 Rev A Transport Frame TransPro 80 Tow-Behind Trailer Model No. 04238—Serial No. 402900001 and Up Installation Instructions Safety Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger.
Installation Mounting the Axle and Ramp (Model 04245) or Rail The Transpro 80 machine is intended for use with (Models 04244 and 04247) Greensmaster 800, 1000, 1010, 1600, 1610, 2000, and 2600 machines, as well as Flex 18, 21, 1800,...
Page 4
Mounting the Wheel Mounting/Adjusting the Assemblies Hitch Straps Mount a wheel assembly to each axle hub with The hitch straps are shipped mounted in the standard 4 lug nuts (Figure 5). Tighten the nuts to 80 ft-lb position (Figure (108 N∙m). Important: The trailer tongue must be parallel to Adjust the tire pressure to 5 psi (34 kPa).
Page 5
Flex 1800, 1820, and 2100, 2120 series equipped). machines require a different wheel offset than On Greensmaster Flex 18 or 21 machines only, all other Toro greensmowers. Read and follow proceed as follows: the mounting instructions molded into the sides of the wheels.
(Figure 11). Lower the trailer bed to the ground. g214902 Figure 12 g014670 Greensmower loaded on a TransPro 80 with Rail Kit Figure 11 1. Latch assembly 2. Handle On flat ramps, pivot the wheel rods upward (Figure 13) and on rail ramps, rotate the wheel...
– When turning or driving on slopes, always slow the tow vehicle, then turn to prevent loss of • The TransPro 80 trailer is intended for use with control and possible upset. Greensmaster 800, 1000, 1600, 2000, 2600 – Do not make sudden or sharp turns. Do not...
Page 8
– Shut off the tow vehicle engine and remove the key. • While the TransPro 80 trailer is disconnected from tow vehicle: – Store the trailer on level ground. – Chock the wheels to prevent the trailer from moving.
Maintenance Recommended Maintenance Schedule(s) Maintenance Service Maintenance Procedure Interval • Check the torque of the wheel lug nuts. After the first 10 hours • Service the wheel hub and inspect for damage. Yearly • Lubricate the wheel hub assembly. Servicing the Wheel Hub Lubricating the Wheel Hub Assembly Service Interval: Yearly...
Checking the Torque of the Wheel Lug Nuts Service Interval: After the first 10 hours Check the torque of the wheel lug nuts at the service interval and each time you install the wheels. WARNING Failure to maintain proper torque could result in failure or loss of wheel and could result in personal injury.
Page 13
The Toro Company (“Toro”) respects your privacy. When you purchase our products, we may collect certain personal information about you, either directly from you or through your local Toro company or dealer. Toro uses this information to fulfil contractual obligations - such as to register your warranty, process your warranty claim or to contact you in the event of a product recall - and for legitimate business purposes - such as to gauge customer satisfaction, improve our products or provide you with product information which may be of interest.
Page 14
While the exposure from Toro products may be negligible or well within the “no significant risk” range, out of an abundance of caution, Toro has elected to provide the Prop 65 warnings. Moreover, if Toro does not provide these warnings, it could be sued by the State of California or by private parties seeking to enforce Prop 65 and subject to substantial penalties.
Page 15
Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact your Authorized Toro Service Center.