Advertisement
Massage bathtub
1.Features(371)：
1、 Automatic testing water level by microcomputer.
2、Surfing function . 3、Bubble bath massage function .
4、External thermostat function （Configuration Options ）
5、Underwater light . 6、Oz one sterilization function （Co nfiguration Opt ions ）
2.Specifications：
1、
Power supply
：AC190V--240V 50-60Hz
2、Water pump1 load：
AC220V-240V
3、
Water
pump2 load：
AC220V-240V
4、
Heater power
：AC220V 2W（
Dielectric strength
：1500V 1min
5
、
6、
Leak current
：<0.25mA
7、Lamp：AC12V 10W
8、Ozone ：AC12V
8W（
Configuration Options
9、
Waterproof grade
：IPX4
3.Install sketch：
（the configuration of installation should be accroding to
the selected model）
Control panel
O K
Ozone devi ce
AC 12V /8W
Water level sensor
AC 220V
INPU T
Water pump
16A Plug
Electric box
1500W
750W
Configuration Options
）
）
Water pump
Heater
220V/2KW
Lamp
12V10W
Page 5 of 7
1、Electricity parameter
Rated voltage
Rated power
Rated electric current
220VAC
2750W
2、Electric installation
2.1
power supply's establishment should be compled with nation security standard, voltage
and frequency also shoule be accord withproduct's nameplate.Especially install creep-
age protect switch and also check whether can connect with ground.
2.2
The wire collected to the massage bathtub should be fitting permanent., and the wire
should be a three-core wire, the sectional acreage of each core cannot less than 12A.
when wire pass the wall,it should be use bushing for protection until the AC outlet.
2.3
Ground wire of bathtub should be test whether works with house appliance ground wire.
2.4
The wire end of electricity control box should connect to the control panel, water bottom
light, loudspeaker, electrical engineering and the detector protection respectively.
3、Water supply device
3.1 This device's hydraulic pressure is 0.2-0.4Mpa.
3.2 The water supply characteristics on the wall: The cold or hot water supplies inside the
bathroom also establish in the shelter of the massage tub, use the hose to connect with
the cold or hot joint of the tub. the pipe towards is decide by the customer, the machine
do not go with the hose.
4、Installation introduction
4.1
Before install, must consider the place of install massage bathtub whether can support
this device's pressure.
4.2
Place the massage bathtub on the install position, adjust level to make the drain system
smooth.
4.3
Adjust the leg's screw to make sure all of the screw touch ground completely.
4.4
Install the drain hose, and make some measure to against on the connecter.
4.5
Fix cold and hot water-pipe well, then install the showerhead. And then put drain into
downcomer, finally connect with power and make sure whether device connected with
ground can work.
5、Using Method
5.1
Turn on faucet, adjust water's temperature, add water to the massage bathtub.when the
highest water level exceed the highest nozzle about 20-30mm and reach the detector,
press the switch button to let the electric machine.
5.2
Revolve the adjust switch ,and choose the proper surf pressure.
5.3
After finishing if should turn off pump at first, then open drain button,when water is all out ,
please make a clean of bathtub to keep in good.
6、Clean and keep in good condition
6. 1 us ua lly us e sof t clot hs an d ge ne ral liqu id clea ns er can wa sh aw ay di rt , bu t for bi d to us e the
clea ns er wi th ac et on e or the ammon ia comp os ition ;wh en di sinf ec t, for bi d to us e the di sinf ec tor
con tai ne d the for mal de hy de .
6. 2 the di rty spo t of sur fac e can us e the too thp as te to wi pe wi th the sof t clot h
6. 3 to the low -gr ad e cha fe of the sur fac e or bu rne d by ciga ret te, can soa k in wa ter to wh et wi th 20 00 #
lev iga tion san d pa pe r, the n po lishi ng .
6. 4 If the el ec trop lat e pi ec e con tai n stai n, us e the sof t clot h to wi pe ligh tly, av oi d to wi pi ng wi th coa rse clot h
6. 5 of ten clea n up the ba ckwa ter ne t cov er, pr ev en t it from stop ;
Massage bathtub
Reference circuit voltage
<4A
12V
.
Page 2 of 7
.
Advertisement
