Toro DDC Series Installation And Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Toro Manuals
  4. Controller
  5. DDC Series
  6. Installation and operating instructions manual

Toro DDC Series Installation And Operating Instructions Manual

Digital dial controller
Hide thumbs Also See for DDC Series:
Table of Contents

Advertisement

Quick Links

DDC™ Series
Digital Dial Controller
INSTALLATION AND
OPERATING INSTRUCTIONS

Advertisement

Table of Contents
loading

Related Manuals for Toro DDC Series

Summary of Contents for Toro DDC Series

  • Page 1 DDC™ Series Digital Dial Controller INSTALLATION AND OPERATING INSTRUCTIONS...

  • Page 2: Table Of Contents

    Thank you for choosing the Toro DDC (Digital Dial Controller) irrigation controller. The DDC incorporates the latest programming technology in an easy-to-use, "digital dial" display. The following instructions will help you get started. As you follow the simple steps, please pay attention to the important NOTES, which will give you helpful hints and programming advice to maximize the feature capability of the DDC.

  • Page 3: Installation Instructions, Indoor

    INSTALLATION INSTRUCTIONS: INDOOR MODELS MULTILINGUAL LCD INLAY - To place or replace look at instructions inside the plastic bag. DIGITAL DIAL advancement button TRANSFORMER RESET BUTTON RESET Install in a SENSOR protected area. 9 volt Battery MASTER VALVE C O M M O N A L L V A L V E S Remove the lower cover of the DDC controller.

  • Page 4: Installation Instructions, Outdoor

    INSTALLATION INSTRUCTIONS: OUTDOOR MODELS Remove the lower cover of the DDC controller by sliding it down. Place the unit on the wall using the top keyhole screw slot. Level the controller, then insert screws into one or more of the three lower screws holes at of the cabinet bottom. Drive the screws through the plastic flashing that keeps the cabinet weather resistant.

  • Page 5: Sensor Connection And Operation

    Toro RainSensor to the C-common terminal and the other wire to the N.C. (normally closed) terminal. As soon as the Toro RainSensor contacts change from the N.C. position to the N.O. (normally open) position, irrigation will be suspended. Irrigation will resume as soon as the Toro RainSensor dries and its contacts return to the N.C.

  • Page 6: Programming

    PROGRAMMING: It is recommended to press the RESET button to clear the memory. Press DIAL to advance to SET TIME/DAY Dial Position: SET TIME/DAY Set the current YEAR, MONTH, DAY & TIME. Set the YEAR with +/ON or -/OFF Press NEXT Set the MONTH with +/ON or -/OFF Press NEXT Set the DAY with +/ON or -/OFF...

  • Page 7: Water Days

    Dial position: WATER DAYS Calendar Interval Even Interval Prog. A Prog. A Prog. A Prog. A start There are 4 choices for your days selection: CAL - Select days of the week. (All days are ON as the default) Int - Select days interval, 1-7 days, and the 1st day to start the interval Odd - Irrigation on Odd days (31st day is skipped) En - Irrigation on Even days.

  • Page 8: Season Adjust/Adjust Water

    Dial position: SEASON ADJUST/ADJUST WATER In this dial position you can increase or decrease the RUN TIME of all stations in that program by percentage scaling from 0% to 200% in 10% increments. Watering percentage is adjusted by month with the default setting being 100% of set runtimes.

  • Page 9: Manual Programs

    Dial Position: MANUAL PROGRAMS The MANUAL PROGRAMS mode allows the immediate start of an entire program (A, B or C). When using the MANUAL PROGRAMS feature, the DDC will essentially override the normal start time and begin immediately. Using MANUAL PROGRAMS does not affect the previously scheduled run times.

  • Page 10: Auto-Run

    Press NEXT to set PROGRAM ERASE function OR Press DIAL to move to AUTO-RUN PROGRAM ERASE – You can erase all program information for a selected program. This can be done for any selected program. Press NEXT to select the program to erase. Press +/ON to erase.

  • Page 11: Self Diagnostic Electronic Fuses

    Toro Warranty Company is liable for failure of products not manufactured by them even though such products may be sold or used in conjunction with Toro products. During such warranty period, we will repair or replace, at our option, any part found to be defective.

  • Page 12: Custom Watering Plan

    "How to Identify and Resolve Radio-TV Interference Problems". This booklet is available from the U.S. Government Printing O ce, Washington, DC 20402. Stock No. 004-000-00345-4. International: This is a CISPR 22 Class B product. The Toro Company www.toro.com Ask for Customer Service...

Table of Contents