Sealey SA623.V2 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE
PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
Read the instruction Wear eye protection
manual.
Follow all workshop health & safety rules, regulations, and conditions when using screwdriver.

WARNING! Disconnect from air supply before changing accessories or servicing.

Maintain screwdriver in good condition and replace any damaged or worn parts. Use genuine parts only. Non-authorised parts may be

dangerous and will invalidate the warranty.
WARNING! Check correct air pressure is maintained and not exceeded. We recommend maximum 90psi (6bar).

Keep air hose away from heat, oil and sharp edges. Check the air hose for wear before each use and ensure that all connections are

secure.
Wear approved safety eye protection, ear protection and protective gloves.

Keep screwdriver bits clean and in good condition for best and safest performance.

Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.

Secure non stable work piece with a clamp, vice or other adequate holding device.

Ensure the screwdriver bit is secure in the chuck.

Avoid unintentional starting.

Keep children and unauthorised persons away from the working area.

DO NOT get the screwdriver

DO NOT hold the workpiece by hand.

DO NOT use the screwdriver for a task it is not designed to perform.

WARNING! DO NOT use the screwdriver if damaged or faulty. Contact your local service agent.

DO NOT use screwdriver unless you have been instructed in its use by a qualified person.

DO NOT drop, throw or abuse the screwdriver.

DO NOT carry the screwdriver by the air hose, or yank the hose from the air supply.

DO NOT operate screwdriver if you are tired, under the influence of alcohol, drugs or intoxicating medication.

DO NOT carry screwdriver with your hand on the power trigger in order to avoid unintentional starting.

DO NOT direct air from the air hose at yourself or others.

When not in use disconnect from air supply and store in a safe, dry, childproof location.

2. INTRODUCTION
Compact design is ideal for accessing work areas where space is limited. Composite lightweight housing reduces effects of chill on operator's
hands. Fully reversible with thumb control on side of motor housing. Air motor with quality bearings for smooth and powerful operation.
Features 6mm quick-release chuck for fast bit changes. Suitable for the professional workshop.
3. SPECIFICATION
Chuck size:. . . . . . . . . . . . . . .6mm Hex
Free speed: . . . . . . . . . . . . . 11000rpm
Torque range: . . . . 68Nm(600lbins)max
Air consumption:. . . . . . 5m³/hour(3cfm)
Operating pressure: . . . 6bar(90psi)max
Air inlet size: . . . . . . . . . . . . . . 1/4" BSP
Weight: . . . . . . . . . . . . . . . . . . . . . 0.7kg
Noise Power: . . . . . . . . . . . . . . 92dB(A)
Noise Pressure: . . . . . . . . . . . . 81dB(A)
4. OPERATION
4.1. Air Supply
4.1.1. Ensure the screwdriver trigger is in the "off" position before connecting to air supply.
4.1.2. You will require an air pressure of 90psi for maximum torque, and an air flow according to specification.
4.1.3.  WARNING! Ensure the air supply is clean and does not exceed 90psi while operating the screwdriver. Too high an air pressure and
unclean air will shorten the product life due to excessive wear, and may be dangerous causing damage and/or personal injury.
4.1.4. Drain the air tank daily. Water in the air line will damage the screwdriver.
4.1.5. Clean air inlet filter weekly. Recommended hook-up procedure is shown in fig.1 and fig.2.
4.1.6. Line pressure should be increased to compensate for unusually long air hoses (over 8 metres). The minimum hose diameter should
be 1/4" I.D. and fittings must have the same.
4.1.7. Keep hose away from heat, oil and sharp edges. Check hose for wear, and make certain that all connections are secure.
© Jack Sealey Limited
INSTRUCTIONS FOR:
AIR PISTOL SCREWDRIVER MINI 600LB IN.
(67NM) COMPOSITE PREMIER
MODEL NO:
Wear ear protection
wet or use in damp or wet locations.
Original Language Version
SA623.V2
Wear protective gloves
SA623_V2 Issue: 2(SP) - 03/11/15