DeWalt XR LI-ION DCS367 Original Instructions Manual
  1. Manuals
  2. Brands
  3. DeWalt Manuals
  4. Cordless Saw
  5. XR LI-ION DCS367
  6. Original instructions manual

DeWalt XR LI-ION DCS367 Original Instructions Manual

Hide thumbs Also See for XR LI-ION DCS367:
Table of Contents

Advertisement

Quick Links

DCS367
Final page size: A5 (148mm x 210mm)

Advertisement

Table of Contents
loading

Related Manuals for DeWalt XR LI-ION DCS367

Summary of Contents for DeWalt XR LI-ION DCS367

  • Page 1 DCS367 Final page size: A5 (148mm x 210mm)
  • Page 2 English (original instructions) Copyright D WALT...
  • Page 3 Fig. A Fig. B Fig. C Fig. D...
  • Page 4 Fig. E Fig. F Fig. G Fig. H Fig. I Fig. J...
  • Page 5 Fig. K...

  • Page 6: Reciprocating Saw

    English CORDLESS RECIPROCATING SAWS DCS367 Congratulations! EC-Declaration of Conformity You have chosen a D WALT tool. Years of experience, thorough Machinery Directive product development and innovation make D WALT one of the most reliable partners for professional power tool users. Technical Data Reciprocating Saw DCS367 DCS367...

  • Page 7: General Power Tool Safety Warnings

    *Date code 201811475B or later **Date code 201536 or later English Batteries Chargers/Charge Times (Minutes) Weight (kg) DCB104 DCB107 DCB112 DCB113 DCB115 DCB118 DCB132 DCB119 Cat # DCB546 18/54 6.0/2.0 1.05 DCB547 18/54 9.0/3.0 1.46 135* 135* DCB548 18/54 12.0/4.0 1.44 DCB181 0.35...

  • Page 8: Switching On And Off

    English h ) Do not let familiarity gained from frequent use of contacts eyes, additionally seek medical help. Liquid tools allow you to become complacent and ignore ejected from the battery may cause irritation or burns. tool safety principles. A careless action can cause severe e ) Do not use a battery pack or tool that is damaged injury within a fraction of a second.

  • Page 9: Important Safety Instructions For All Battery Chargers

    English Using an Extension Cable • Wherever possible, use clamps and vices to fasten the workpiece securely. An extension cord should not be used unless absolutely • Do not attempt to saw extremely small workpieces. necessary. Use an approved extension cable suitable for the power input of your charger (see Technical Data).

  • Page 10: Charger Operation

    English If the charger indicates a problem, take the charger and battery charger is ventilated through slots in the top and the bottom of the housing. pack to be tested at an authorised service centre. • Do not operate charger with damaged cord or plug— hot/Cold Pack Delay have them replaced immediately.
  • Page 11 English READ ALL INSTRUCTIONS that could contact them and cause a short circuit. NOTE: Lithium-ion batteries should not be put in • Do not charge or use battery in explosive atmospheres, checked baggage. such as in the presence of flammable liquids, gases or WALT batteries comply with all applicable shipping dust.

  • Page 12: Storage Recommendations

    English batteries of 36 Wh each. The Use Wh rating might indicate TRANSPORT (with built-in transport cap). Example: 108 Wh (1 battery implied). Wh rating indicates 3 x 36 Wh (3 batteries of 36 Wh). Storage Recommendations Battery Type 1. The best storage place is one that is cool and dry away The DCS367 operates on 18 volt battery packs.

  • Page 13: Intended Use

    English Worklight in the battery is below the usable limit, the fuel gauge will not illuminate and the battery will need to be recharged. Datecode nOTE: The fuel gauge is only an indication of the charge left on Intended Use the battery pack. It does not indicate tool functionality and is Your DCS367 cordless reciprocating saws have been designed subject to variation based on product components, temperature for professional sawing of wood, metal and tubes.

  • Page 14: Maintenance

    English during the cut (Fig. E). Increased risk of personal injury, as cuts. Failure to do so may result in explosion, property well as damage to the shoe and workpiece may result. damage, electric shock, and/or serious personal injury. To install blade into saw Flush-To Cutting (Fig.

  • Page 15: Optional Accessories

    English Cleaning WARNING: Blow dirt and dust out of the main housing with dry air as often as dirt is seen collecting in and around the air vents. Wear approved eye protection and approved dust mask when performing this procedure. WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts of the tool.
  • Page 16 Belgique et WALT - Belgium BVBA Tel: NL 32 15 47 37 63 www.dewalt.be Luxembourg België en Luxemburg Egide Walschaertsstraat 16 Tel: FR 32 15 47 37 64 enduser.BE@SBDinc.com 2800 Mechelen Fax: 32 15 47 37 99 Danmark WALT (Stanley Black&Decker AS)

Table of Contents