Sharp XV-Z9000U Service Manual
  1. Manuals
  2. Brands
  3. Sharp Manuals
  4. Projector
  5. XV-Z9000U - Vision - DLP Projector
  6. Service manual

Sharp XV-Z9000U Service Manual

Hide thumbs Also See for XV-Z9000U:
Table of Contents

Advertisement

Quick Links

Download this manual
In the interests of user-safety (Required by safety regulations in some countries) the set should be restored
to its original condition and only parts identical to those specified should be used.
Im lnteresse der Benutzersicherheit (erforderliche Sicherheitsregeln in einigen Ländern) muß das Gerät in seinen
Originalzustand gebracht werden. Außerdem dürfen für die spezifizierten Bauteile nur identische Teile verwendet
werden.
SHARP CORPORATION
SERVICE MANUAL
SERVICE-ANLEITUNG
DLP PROJECTOR
DLP PROJEKTOR
MODELS
XV-Z9000U/E
MODELLE
This document has been published to be used for
after sales service only.
1
The contents are subject to change without notice.
XV-Z9000U/E
S81Y7XVZ9000U

Advertisement

Table of Contents
loading

Related Manuals for Sharp XV-Z9000U

Summary of Contents for Sharp XV-Z9000U

  • Page 1 XV-Z9000U/E SERVICE MANUAL SERVICE-ANLEITUNG S81Y7XVZ9000U DLP PROJECTOR DLP PROJEKTOR MODELS XV-Z9000U/E MODELLE In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified should be used.

  • Page 2: Table Of Contents

    XV-Z9000U/E CONTENTS Page Page • SPECIFICATIONS ..........3 • SCHEMATIC DIAGRAM ........ 100 • INPOTANT SERVICE SAFETY NOTES .... 4 • PRINTED WIRING BOARD ASSEMBLIES ... 133 • OPERATION MANUAL ........8 • PARTS LIST Ë ELECTRICAL PARTS ....... 140 •...

  • Page 3: Specifications

    Weight (approx.) 20.9 lbs.(9.5 kg) Supplied accessories Remote control, Two AA size batteries, Power cord (11' 10" ,3.6 m(XV-Z9000U), 1.8m(XV-Z9000E)), Lens cap (attached), DLP projector operation manual, CD-ROM, CD-ROM operation manual, Terminal cover, Video cable(XV-Z9000E), VGA cable(XV-Z9000E), 21pin-RCA adaptor(XV- Z9000E), Guarrantee card for U.S., Guarrantee card for CANADA.
  • Page 4 XV-Z9000U/E IMPORTANT SERVICE SAFETY NOTES (for USA) Ë Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and servicing guidelines as follows: » Use an AC voltmeter with sensitivity of 5000 ohm per WARNING volt., or higher, sensitivity to measure the AC voltage...
  • Page 5 XV-Z9000U/E NOTE TO SERVICE NOTE POUR LE PERSONNEL PERSONNEL D’ENTRETIEN 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5...
  • Page 6 XV-Z9000U/E 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5...
  • Page 7 XV-Z9000U/E WARNING: High brightness light source, do not stare into the beam of light, or view directly. Be especially careful that children do not stare directly in to the beam of light. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO MOISTURE OR WET LOCATIONS.
  • Page 8 XV-Z9000U/E Location of Controls Projector Front and Top View Remote control sensor Lens shift dial Zoom knob TEMPERATURE WARNING indicator LAMP REPLACEMENT indicator Focus ring POWER indicator Adjuster Intake ventilative hole Adjuster Remote control sensor Lens cap MENU button RESIZE button ADJUSTMENT buttons ('/"/\/|)
  • Page 9 XV-Z9000U/E Projector Side and Rear Vie Intake ventilative hole Intake ventilative hole 4 Exhaust ventilative hole Remote control sensor S-VIDEO INPUT 3 terminal (4-pin Mini DIN) RS-232C port INPUT 5 COMPUTER-RGB port INPUT 1 COMPONENT/ (9-pin D-sub) (15-pin Mini D-sub)
  • Page 10 XV-Z9000U/E Remote Control Front View POWER buttons (ON/OFF) MENU button ENTER button ADJUSTMENT buttons (\/|/'/") UNDO button INPUT 1 button INPUT 3 button INPUT 2 button INPUT 5 button INPUT 4 button RESIZE button THEATER MODE button CLR TEMP buttons...
  • Page 11 XV-Z9000U/E The remote control can be used to contr ol the projec- tor within the range shown on the left. Remote Control • The signal from the remote control can be reflected off a 23 (7 m) 30˚ screen for easy operation. However, the effective distance of the signal may differ due to the scr een material.
  • Page 12 XV-Z9000U/E Connection Pin Assignments INPUT 5 RGB Signal Input Port: 15-pin Mini D-sub female connector RGB Input Analog 8. Earth (blue) 1. Video input (red) 9. Not connected 2. Video input 10. GND (green/sync on green) 11. GND 3. Video input (blue) 12.
  • Page 13 XV-Z9000U/E Dimensions Rear View Side View Top View Side View Front View (475) Bottom View Unit: inches (mm)

  • Page 14: Removing Of Major Parts

    XV-Z9000U/E REMOVING OF MAJOR PARTS 1. Removing the top panels 1-1. Remove the six lock screw. 2-1. Remove the two screws and detach the LED PWB. 1-2. Press on side Arrow A of the bottom body 2-2. Remove the one screw and detach the R/C PWB.
  • Page 15 XV-Z9000U/E 2. Removing the cooling fan and PWB unit assembly. 3-1. Disconnect the eleven connectors. 3-2. Remove the two screws and detach the lamp socket. 3-3. Remove the two screws and detach the cooling fan. 3-4. Remove the four screws and detach the PWB unit assembly.
  • Page 16 XV-Z9000U/E 3. Removing the rear panel, PC unit, cooling duct and main PWB unit. 4-1. Remove the two screws. 4-2. Remove the three screws and detach the rear panel. 5-1. Remove the two screws. 5-2. Remove the four hexagonal supports and detach the shield plate.
  • Page 17 XV-Z9000U/E 4. Removing the power unit shield , power/ballast unit and power unit. Remove the seven screws and detach the power unit shield. 10-1. Remove the two screws. 10-2. Remove the four white supports and detach the power unit. Remove the four screws and detach the power unit.
  • Page 18 XV-Z9000U/E 5. Removing the optical mechanism unit and R/C PWB unit. Remove the six screws and detach the optical mechanism unit. Remove the one screw and detach the R/C PWB unit. Optical mechanism unit R/C PWB unit...
  • Page 19 XV-Z9000U/E 6. Removing the lamp unit, CW fan, outlet fan, bimetal, wind way duct, shield plate and formater PWB. Remove the three screws and detach the lamp unit. Remove the two screws and detach the CW fan. Remove the three screws and detach the outlet fan.

  • Page 20: Resetting The Total Lamp Timer

    The lamp does not • Lamp circuit failure. • Take the projector to your nearest MENT indicator light up. Authorized Sharp Vision Service Center or The lamp requires • Lamp has been used for Dealer for repair. replacement. over 1,900 hours.

  • Page 21: The Optical Unit Outline

    XV-Z9000U/E THE OPTICAL UNIT OUTLINE Layout for proper setup of the optical components and parts (top view) Projection lens Prism DMD Chips Condensor lens IR-cut mirror Light tunnel Relay lens Fold mirror Condensor lens Color filter Lamp Item Descriptions 1 Lamp The DC Light source lamp with parabola reflector.
  • Page 22 XV-Z9000U/E Adjusting the mirrors Make adjustment by the indication territory on the screen to prevent the circumference of the screen from getting dark because a lighting range deviated. 1. Remove the top body so that the optical unit may be seen. Display white only screen on the screen.
  • Page 23 XV-Z9000U/E When the DMD unit has been replaced Note: DMD chip and Formatter PWB are supplied at the same time, and an exchange only with DMD isn't done.Refer to "REMOVING OF MAJOR PARTS" when exchanging Formatter PWB. There is no need to readjust the back focal distance of the projection lens. If focusing is noticeably poor, however, make this readjustment.

  • Page 24: Electrical Adjustment

    XV-Z9000U/E ELECTRICAL ADJUSTMENT Hook up a signal generator, or a DOSV or Mac personal computer to the projector in order to feed the signals specified in the Adjusting conditions. Adjusting point Adjusting conditions Adjusting procedure EEPROM 1. Make the following settings.
  • Page 25 XV-Z9000U/E Adjusting point Adjusting conditions Adjusting procedure 1. Make sure the 100% and 95% white and the 0% RGB tone 1. Feed the SMPTE pattern and 5% black tones are visible. reproduction signal. adjustment 2. If the black tone appears otherwise, finely adjust the INPUT5 R-BRIGHT, G-BRIGHT and B-BRIGHT settings.
  • Page 26 XV-Z9000U/E Adjusting point Adjusting conditions Adjusting procedure 1. Check the fixed setting. NTSC color 1. Feed the internal 8CH (split Fixed setting: 105 saturation color bar) signal. adjustment INPUT4 2. Select the following group and subject. Group: VIDEO1 Subject: N-COLOR 1.
  • Page 27 XV-Z9000U/E Adjusting point Adjusting conditions Adjusting procedure White balance 1. Take the adjustment con- Make sure there is no white balance difference be- checking and ditions discussed for Item tween the set and the standard monitor. readjustment Color-related 1. Feed the color bar signal.
  • Page 28 6) Adjust the CR-OFFSET setting of Group DTV to 20. 7) When the CB-OFFSET and CR-OFFSET settings have been made, add 5 points to the G-BRIGHT setting for Model XV-Z9000U and 4 points for Model XV-Z9000E. 8) Finally press SW2002 to exit from the process mode.
  • Page 29 XV-Z9000U/E Process menu 1 Group Sub Group Subject Adjust PC Image R-BRIGHT G-BRIGHT B-BRIGHT Adjust HDDE formatter VOLTAGE CW-INDEX R-BRIGHT G-BRIGHT B-BRIGHT R-GAIN G-GAIN B-GAIN Adjust Component G-BRIGHT (High Definition) CB-OFFSET CR-OFFSET Adjust VIDEO Image VIDEO1 NTSC-H PICTURE BRIGHT TINT...
  • Page 30 XV-Z9000U/E Process menu 2 Group Sub Group Subject Process mode LINE TEMP OFF SENSOR CHECK INITIAL SETTING TIME LAMP Sample Pattern PATTERN RGB(50) CROSS STEP COLOR Adjust CVIC CVIC MODDE -PROGRESSIVE FILM C-LEVEL C-LIMIT C-LPF C-THRESH C-MISSTH C-MOVIEA C-MOVIEB C-MOVIEC...
  • Page 31 XV-Z9000U/E Process menu 3 Group Sub Group Subject Adjust CVIC CVIC BBN-TBL0 -ENHANCE-VIDEO BBN-TBL1 DFC-TBL0 DFC-DIR0 DFC-EDG0 DFCTBL1 DFC-DIR1 DFC-EDG1 CVIC BBN-TBL0 -ENHANCE-HDTV BBN-TBL1 DFC-TBL DFC-DIR DFC-EDG CVIC BBN-GAIN0 -ENHANCE-RGB BBN-GAIN1 BBN-GAIN2 BBN-TBL DFC-TBL DFC-DIR DFC-EDG CVIC CUBIC-RGB -SCREEN CUBIC-VIDEO...

  • Page 32: Trouble Shooting Table

    XV-Z9000U/E TROUBLE SHOOTING TABLE Checking the basic performance Is the POWER LED on or flickering in red or blue? Go to "Checking the power unit" Is the set turned on by the set's or remote controller's power key? Go to "Checking the microcomputer peripherals"...
  • Page 33 XV-Z9000U/E Checking the power unit Are all the connectors inside the power unit tightly connected? Insert the connectors CN7105, 7103, 7101AND 7102 tightly. Is the lamp cover closed completely? Tighten up the lamp door closed with the screws. Is the bimetal switch off?
  • Page 34 XV-Z9000U/E Checking the PC PWB Is the user menu properly displayed? Check the on-screen display. Check the basic signal flow. The signal flow from CVIC_IC to the panel output is the same for the component and video signals. Therefore the lines after CVIC are not checked.
  • Page 35 XV-Z9000U/E Checking the RGB input Feed the sync-separated DTV RGB signal to INPUT1 or INPUT2. (The 480i and 580i component signals are not included.) Using the front-panel key or the remote control, select INPUT1 or INPUT2. Does the image appear? Check to see if the video input is as specified.
  • Page 36 XV-Z9000U/E Checking the video input Make sure the input signal setting is as specified. Is there the video signal at the land of C8077? Input PWB defective. Check the sync signal. IC8025 or IC8004 defective. Checking the input signal setting...
  • Page 37 XV-Z9000U/E Checking the sync signal Is there vertical sync signal at TL8134? Is there horizontal sync signal at TL8133? Check the input signal setting. Input PWB defective. Is there vertical sync signal at TL8131? Is there horizontal sync signal at TL8130?
  • Page 38 XV-Z9000U/E Checking the RGB signal Is the type of signal set at RGB? Set to the RGB signal. Call the process mode. Select R, G and B separately on the pattern menu. Go to “Checking the GA4 peripheral circuits”. Set the signal generator to...
  • Page 39 XV-Z9000U/E Checking the GA4 peripheral circuits Call the process mode, and select R, G and B separately on the pattern menu. Are there specified R, G and B video output signals? End of checking the GA4 peripheral circuits. Are the measured signals...
  • Page 40 XV-Z9000U/E Checking the component inputs (Except for 480I) Feed the component signal to INPUT1 or INPUT2. Using the front panel key or the remote control, select INPUT1 or INPUT2. Does an image appear on the screen? Go to "Checking the SOG circuit".
  • Page 41 XV-Z9000U/E Checking the SOG circuit Measure the signal at TL8136 on the oscilloscope. Is the composite sync signal played back timely? There is no problem with the SOG circuit. End. Measure the land of C8069 on the oscilloscope. Is there the Y signal including the sync signal? Go to “Checking the input...
  • Page 42 XV-Z9000U/E Checking the video input Feed the composite video signal to INPUT4. Using the front panel key or the remote control, select INPUT4. Select VIDEO as the type of signal on the user menu. Does the image appear? Go to "Checking the video sync signal".
  • Page 43 XV-Z9000U/E Measure the VPC (IC8338) clock signal at TL8004. Is the clock signal as specified? IC8338 defective. Go to “Checking the video sync signal”. IC8025 or its peripheral circuit defective. Checking the video sync signal Using the oscilloscope, measure the signal at TL8140.
  • Page 44 XV-Z9000U/E Checking the DSUB input. Feed the PC-RGB signal to INPUT5. Select INPUT5 as the input. Check to see if there are the R, G and B signals at pins (126), (136) Does the image appear? and (146) of IC8004.
  • Page 45 XV-Z9000U/E Checking the lamp light-up The lamp fails to light up. Is discharge sound heard when turning on the power switch? Is the lamp or CW line socket out of position? Reconnect the sockets tightly. Replace the lamp or the...
  • Page 46 XV-Z9000U/E No horizontal synchronization Is the terminal input connection as specified? Is the cable tightly connected? Use the specified cable. Reconnect it tight enough. Is there the horizontal sync pulse at pin (14) of IC2506? Check the line between IC2506 and the input terminal.
  • Page 47 XV-Z9000U/E Checking IC3504 (3D Noise Reduction) and its Peripheral Circuits Are there the input signals at pins (88) (Y signal) and (96) (C signal) of IC3504? Check the signal input circuit or IC2505 and its peripheral circuits. Are there the output...
  • Page 48 XV-Z9000U/E Checking the Component and RGB Inputs Are there signals at pins (34), (36) and (38) of IC2505? Check the signal input circuit or IC2505 and its peripheral circuits. There are no RGB colors. Check the circuit of the color that fails to appear.
  • Page 49 XV-Z9000U/E XV-Z9000U/E CHASSIS LAYOUT / CHASSIS-ANORDNUNG...

  • Page 50: Block Diagram

    XV-Z9000U/E XV-Z9000U/E BLOCK DIAGRAM / BLOCKSCHALTBILD...

  • Page 51: Overall Wiring Diagram

    XV-Z9000U/E XV-Z9000U/E OVERALL WIRING DIAGRAM / GESAMTSCHALTPLAN...

  • Page 52: Description Of Schematic Diagram

    XV-Z9000U/E DESCRIPTION OF BESCHREIBUNG DES SCHEMATIC DIAGRAM SCHEMATISCHEN SCHALTPLANS VOLTAGE MEASUREMENT CONDITION: SPANNUNGSMESSUNGEN: 1. Voltages at test points are measured at the 1. Spannungen an den Prüfpunkten werden bei einer Netzspannung von 220V gemessen, Signale werden supply voltage of AC 220V. Signals are fed by a für die Wartung mit einem Farbbalken-Signal generator...
  • Page 53 XV-Z9000U/E WAVEFORMS / WELLENFORMEN 1 P3580 32 2 P3580 34 3 P3580 4 4 P3580 47 (VIDEO AC) (Y-signal) (CHROMA signal) (RGB) H : 20µ sec/div H : 10µ sec/div H : 10µ sec/div H : 20µ sec/div V : 500mV/div V : 0.2V/div...
  • Page 54 XV-Z9000U/E XV-Z9000U/E Ë MAIN UNIT / HAUPT-EINHEIT -1/5...
  • Page 55 XV-Z9000U/E XV-Z9000U/E Ë MAIN UNIT / HAUPT-EINHEIT -2/5...
  • Page 56 XV-Z9000U/E XV-Z9000U/E Ë MAIN UNIT / HAUPT-EINHEIT -3/5...
  • Page 57 XV-Z9000U/E XV-Z9000U/E Ë MAIN UNIT / HAUPT-EINHEIT -4/5...
  • Page 58 XV-Z9000U/E XV-Z9000U/E Ë MAIN UNIT / HAUPT-EINHEIT -5/5...
  • Page 59 XV-Z9000U/E Ë KEY UNIT / TASTE-EINHEIT...
  • Page 60 XV-9000U/E Ë R/C RECEIVER (Front) Unit / EINLASSEINHEIT (Vorder) Ë R/C RECEIVER (Rear) Unit / EINLASSEINHEIT (Hinter)
  • Page 61 XV-Z9000U/E XV-Z9000U/E Ë POWER UNIT / NETZTEINHEIT...
  • Page 62 XV-Z9000U/E XV-Z9000U/E Ë PC I/F UNIT / PC-I/F-EINHEIT-1/9...
  • Page 63 XV-Z9000U/E XV-Z9000U/E Ë PC I/F UNIT / PC-I/F-EINHEIT-2/9...
  • Page 64 XV-Z9000U/E XV-Z9000U/E Ë PC I/F UNIT / PC-I/F-EINHEIT-3/9...
  • Page 65 XV-Z9000U/E XV-Z9000U/E Ë PC I/F UNIT / PC-I/F-EINHEIT-4/9...
  • Page 66 XV-Z9000U/E XV-Z9000U/E Ë PC I/F UNIT / PC-I/F-EINHEIT-5/9...
  • Page 67 XV-Z9000U/E XV-Z9000U/E Ë PC I/F UNIT / PC-I/F-EINHEIT-6/9...
  • Page 68 XV-Z9000U/E XV-Z9000U/E Ë PC I/F UNIT / PC-I/F-EINHEIT-7/9...
  • Page 69 XV-Z9000U/E XV-Z9000U/E Ë PC I/F UNIT / PC-I/F-EINHEIT-8/9...
  • Page 70 XV-Z9000U/E XV-Z9000U/E Ë PC I/F UNIT / PC-I/F-EINHEIT-9/9...
  • Page 71 XV-Z9000U/E Ë LED UNIT/ LED-EINHEIT...

  • Page 72: Printed Wiring Board Assemblies

    XV-Z9000U/E PRINTED WIRING BOARD ASSEMBLIES LEITERPLATTENEINHEITEN Power Unit (Component Side) Netzteinheit (Bestückungsseite) Power Unit (Wiring Side) Netzteinheit (Leiterbahnseite)
  • Page 73 XV-Z9000U/E Main Unit (Component Side) Haupt-einheit (Bestückungsseite)
  • Page 74 XV-Z9000U/E Main Unit (Wiring Side) Haupt-einheit (Leiterbahnseite)
  • Page 75 XV-Z9000U/E Key Unit (Component Side) Taste-Einheit (Bestückungsseite) R/C Receiver (Rear) Unit (Component Side) Einlasseinheit (Hinter) (Bestückungsseite) R/C Receiver (Front) Unit (Component Side) Einlasseinheit (Vorder) (Bestückungsseite) LED Unit (Component Side) LED-Einheit (Bestückungsseite)
  • Page 76 XV-Z9000U/E Key Unit (Wiring Side) Taste-Einheit (Leiterbahnseite) R/C Receiver (Rear)Unit (Wiring Side) Einlasseinheit (Hinter) (Leiterbahnseite) R/C Receiver (Front)Unit (Wiring Side) Einlasseinheit (Vorder) (Leiterbahnseite) LED Unit (Wiring Side) LED-Einheit (Leiterbahnseite)
  • Page 77 XV-Z9000U/E PC I/F Unit (Component Side) PC-I/F-einheit (Bestückungsseite)
  • Page 78 XV-Z9000U/E PC I/F Unit (Wiring Side) PC-I/F-einheit (Leiterbahnseite)

  • Page 79: Ersatzteilliste

    Contact your nearest SHARP Parts Distributor. For location of SHARP Parts Distributor, 5. KODE 6. QUANTITÄT Please call Toll-Free; 1-800-BE-SHARP in CANADA: Contact SHARP Electronics of Canada Limited Phone (416) 890-2100. MARK: SPARE PARTS-DELIVERY SECTION MARKIERUNG : ERSATZTEILE-LIEFERUNG Ref. No.
  • Page 80 XV-Z9000U/E Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTKA471DE02/03 D2514 VHDKDS226//-1Y J Diode D2515 VHDKDS226//-1Y J Diode MAIN UNIT(Continued) D2516 RH-EX1264CEZZ J Zener Diode (9V) D2519 RH-EX1264CEZZ J Zener Diode (9V) Q2002 VSRN4982///-1 J RN4982...
  • Page 81 XV-Z9000U/E Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTKA471DE02/03 C2584 VCEAPF0JW227MY J 220 6.3V Electrolytic C2585 VCEAPF0JW227MY J 220 6.3V Electrolytic MAIN UNIT(Continued) C2586 VCEAPF0JW227MY J 220 6.3V Electrolytic C2587 VCEAPF0JW227MY J 220 6.3V Electrolytic C2006 VCKYCY1EF104Z J 0.1...
  • Page 82 XV-Z9000U/E Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTKA471DE02/03 R2025 VRS-CB1JF101J J 100 1/16W Metal Oxide R2027 VRS-CA1JF101J J 100 1/16W Metal Oxide MAIN UNIT(Continued) R2028 VRS-CY1JF100J J 10 1/16W Metal Oxide R2029 VRS-CY1JF100J J 10...
  • Page 83 XV-Z9000U/E Ref. No. Part No. Description Code Ref. No. Part No. Description Code R2692 VRS-CY1JF104J J 100k 1/16W Metal Oxide DUNTKA471DE02/03 R2693 VRS-CY1JF104J J 100k 1/16W Metal Oxide MAIN UNIT(Continued) R2697 VRS-CY1JF153J J 15k 1/16W Metal Oxide R2700 VRS-CY1JF103J J 10k...
  • Page 84 J 100 1/16W Metal Oxide FB3507 RBLN-0064TAZZ J Ferrite Bead R3563 VRS-CY1JF104J J 100k 1/16W Metal Oxide J2501 QJAKLA001WJZZ J Jack (XV-Z9000U) R3564 VRS-CY1JF104J J 100k 1/16W Metal Oxide J2501 QJAKL0012CEZZ J Jack (XV-Z9000E) R3570 VRS-TW2ED391J J 390 1/4W Metal Oxide...
  • Page 85 XV-Z9000U/E Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTKA471DE02/03 DUNTKA473DE02/03 MAIN UNIT(Continued) R/C FRONT UNIT CAPACITORS P2806 QPLGN0540FJZZY J Plug 3-Pin (FC) P2807 QPLGN0565FJZZY J Plug 4-Pin (FD) C2401 VCKYCY1EF104Z J 0.1 Ceramic P2809 QPLGN0464TAZZ...
  • Page 86 XV-Z9000U/E Ref. No. Part No. Description Code Ref. No. Part No. Description Code RDENC0329CEZZ PACKAGED CIRCUITS POWER UNIT PTC7001 95C0D802A1010 J PTH9M04BD222TS2F333 å TRA7001 95C0D513A6120 J SM12JZ47 å Z7001 95C0D754A4710 J ENC471 INTEGRATED CIRCUITS å IC7001 95CH1101AC001 J FA5332M COILS AND TRANSFORMER...
  • Page 87 XV-Z9000U/E Ref. No. Part No. Description Code Ref. No. Part No. Description Code R7057 95C0R391T4740 J 470k 1/4W RDENC0329CEZZ R7061 95C0R451C1000 J 10 POWER UNIT(Continued) R7101 95C0R3Q4S2240 J 220k 1/16W R7102 95C0R3Q4S2710 J 270 1/16W C7354 95C0C1Q2B1040 J 0.1 Ceramic...
  • Page 88 XV-Z9000U/E Ref. No. Part No. Description Code Ref. No. Part No. Description Code IC8319 9DK001-11024 J HY57V653220BTC-7 RDENC0329CEZZ IC8320 9DK001-11024 J HY57V653220BTC-7 POWER UNIT(Continued) IC8321 9DK001-11024 J HY57V653220BTC-7 IC8322 9DK001-11024 J HY57V653220BTC-7 R7414 95C0R3Q4S1030 J 10k 1/16W IC8325 9DK001-12068 J SN74F153DB...
  • Page 89 XV-Z9000U/E Ref. No. Part No. Description Code Ref. No. Part No. Description Code C8079 9DK001-40078 J 22 Electrolytic CPCi-0051CE01/02 C8080 9DK001-40079 J 47 Electrolytic PC I/F UNIT(Continued) C8081 9DK001-42096 J 0.01 Ceramic C8082 9DK001-42096 J 0.01 Ceramic COILS C8083 9DK001-42096 J 0.01...
  • Page 90 XV-Z9000U/E Ref. No. Part No. Description Code Ref. No. Part No. Description Code C8678 9DK001-42094 J 0.1 Ceramic CPCi-0051CE01/02 C8680 9DK001-42094 J 0.1 Ceramic PC I/F UNIT(Continued) C8682 9DK001-42094 J 0.1 Ceramic C8684 9DK001-42094 J 0.1 Ceramic C8564 9DK001-40089 J 47 6.3V Electrolytic...
  • Page 91 XV-Z9000U/E Ref. No. Part No. Description Code Ref. No. Part No. Description Code R8124 9DK001-50237 J 1.0k 1/16W Chip1608 CPCi-0051CE01/02 R8128 9DK001-50150 J 10 1/16W Chip1608 PC I/F UNIT(Continued) R8130 9DK001-50210 J 33k 1/16W Chip1608 R8131 9DK001-50210 J 33k 1/16W Chip1608 C8874 9DK001-42094 J 0.1...
  • Page 92 XV-Z9000U/E Ref. No. Part No. Description Code Ref. No. Part No. Description Code CPCi-0051CE01/02 PC I/F UNIT(Continued) R8893 9DK001-50197 J 2.7k 1/16W Chip1608 R8894 9DK001-50210 J 33k 1/16W Chip1608 R8896 9DK001-50191 J 150 1/16W Chip1608 R8897 9DK001-50161 J 47 1/16W Chip1608...
  • Page 93 10-4 QCNW-4674CEZZ J Door Switch 2-1-11 PFILD0136CEZZ J Intake Filter B 2-1-12 PFILD0137CEZZ J Intake Filter CPCi-0051CE01 - PC I/F Unit Ass'y(XV-Z9000U) — 2-1-13 PMLT-0400CEZZ J Molt CPCi-0051CE02 - PC I/F Unit Ass'y(XV-Z9000E) — 2-1-14 PMLT-0403CEZZ J Molt 11-1 PSLDM3044CEFW...
  • Page 94 XV-Z9000U/E CABINET AND MECHANICAL PARTS/ GEHÄUSE UND MECHANISCHE BAUTEILE 11-3 1-1-5 11-1 1-1-4 1-1-6 1-13 1-1-3 1-16 11-4 1-1-1 1-20 1-1-2 1-14 11-2 1-1-9 1-20 32 17 1-15 1-10 1-20 1-11 1-20 1-1-8 1-20 1-19 1-12 1-20 12-2 12-2 1-18...
  • Page 95 å 67 RLMPF0074CEZZ J Lamp 6-41 CMiR-0291CE01 J Color Wheel Not Available - Formatter unit — TLABN0401CEZZ J S/I No. Label (XV-Z9000U) TLABN0400CEZZ J S/I No. Label (XV-Z9000E) XBBSN30P10000 J Screw, x2 XBBSN40P10000 J Screw, x6 XBPSD30P08R00 J Screw, x13 XBPSD30P18JS0...
  • Page 96 XV-Z9000U/E OPTICS MECHANISM PARTS/ TEILE FÜR OPTIKMECHANISMUS 6-19 6-20 6-21 6-15 6-16 6-16 6-31 6-12 6-36 6-41 6-39 6-11 6-34 6-14 6-13 6-10 6-17 6-18 6-38 6-31 6-37 6-29 6-33 6-30 6-33 6-33 6-35 6-32 6-33 6-27 6-25 6-28 6-26...
  • Page 97 Description Code PACKING PARTS SUPPLIED ACCESSORIES (NOT REPLACEMENT ITEM) QACCU5013CEZZ J AC Cord (For US. and Canada) AX SPAKC5549CEZZ – Packing Case (XV-Z9000U) — å QACCV4002CEZZ J AC Cord (For Europe) SPAKC5623CEZZ – Packing Case (XV-Z9000E) — å QACCB5024CENA J AC Cord SPAKP0910CEZZ –...

  • Page 98: Verpacken Des Geräts

    Code PACKING OF THE SET / VERPACKEN DES GERÄTS Polystyrene Cover (SSAKA1109CEZZ) Terminal Cover (CCOVA1985CE01) Operation Manual (TiNS-7416CEZZ : XV-Z9000U) Operation Manual 1 (TiNS-7521CEZZ : XV-Z9000E) Operation Manual 2 (TiNS-7522CEZZ : XV-Z9000E) CD ROM Manual Sleeve for Accessories (TiNS-7418CEZZ : XV-Z9000U)
  • Page 99 XV-Z9000U/E COPYRIGHT © 2001 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.

This manual is also suitable for:

Xv-z9000e

Table of Contents