Sealey PC200SD.V3 Quick Start Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Read before Wear
first use protective
clothing
1. SAFETY
1.1 ELECTRICAL SAFETY
WARNING! It is the user's responsibility to check the following:
‰
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
all electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all
electrical products. You may obtain an RCD by contacting your local Sealey stockist.
If the lamp is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable
Appliance Test) tested.
Electrical safety information, it is important that the following information is read and understood.
1.0.1. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.0.2. Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
1.0.3.
correct fuse - see fuse rating in these instructions.
DO NOT pull or carry the appliance by the power cable.
8
DO NOT pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a firm grip on the plug.
8
DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or replaced immediately by a
8
qualified electrician.
1.0.4. This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
Class II products are wired with live (brown) and neutral (blue) only are marked with the
Class II symbol;
A) Connect the BROWN live wire to the live terminal 'L'.
B) Connect the BLUE neutral wire to the neutral terminal 'N'.
C) After wiring, check that there are no bare wires and ensure that all wires have been correctly
connected.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
DO NOT connect either wire to the earth terminal.
8
Sealey recommend that repairs are carried out by a qualified electrician.
1.2 GENERAL SAFETY
Disconnect the cleaner from the power supply before servicing, changing accessories, or performing any maintenance.
9
Use only genuine parts and accessories. Unauthorised parts and accessories may be dangerous and will invalidate your warranty.
9
Maintain the cleaner in good condition. Use an authorised agent for servicing. Keep machine clean, but DO NOT use solvents.
9
For dry vacuuming ensure the cartridge filter is locked in place before operating the cleaner.
9
DO NOT operate the unit without the locking cartridge filter in place (except when wet vacuuming). Using the cleaner without a
8
cartridge filter will cause machine faults and will invalidate your warranty.
Wear protective clothing and gloves.
9
DO NOT allow children or untrained persons to operate the cleaner.
8
DO NOT place attachments close to your face (especially eyes, ears, etc).
8
DO NOT point the hose end at other persons or animals.
8
DANGER! DO NOT vacuum hot or glowing ash, cigarette ends, inflammable, explosive, corrosive or other dangerous substances.
‰
DO NOT operate the unit without the dust bag or optional cartridge filter (except when wet vacuuming).
8
DO NOT leave machine running unattended. Turn power supply OFF. DO NOT leave the vicinity until motor has come to a complete stop.
8
DO NOT operate the cleaner while under the influence of drugs, alcohol or impairing medication, or if you are tired.
8
DO NOT use the cleaner in the rain or in very damp conditions.
8
DO NOT use the cleaner for a task it is not designed to perform.
8
When not in use, store the cleaner in a safe, dry, childproof location.
9
© Jack Sealey Limited
20L WET & DRY INDUSTRIAL VACUUM
CLEANER 1250W STAINLESS DRUM
PC200SD.V3
MODEL NO:
Wear Wear
protective eye
gloves protection
Original Language Version
Recommended fuse rating
13 Amp
PC200SD.V3 Issue 4 (4,F) 08/09/20