Related Manuals for ABB Ability ATT-VZN SIM card ready gateway
Summary of Contents for ABB Ability ATT-VZN SIM card ready gateway
- Page 1 — I N S TA L L AT I O N M A N UA L ABB Ability™ Smart Sensor Bluetooth® ATT-VZN SIM card ready gateway...
-
Page 3: Table Of Contents
— Table of contents 1 – General 2 – Installation 2.1 – Prerequisites for installation 2.2 – Recommended location 2.3 – Obtaining the correct SIM card 2.4 – SIM card installation 2.5 – Gateway configuration 2.6 – AT&T mobile network configuration 2.7 –... -
Page 4: General
— 1 – General The ABB Ability Smart Sensor ATT-VZN SIM card ready gateway is used to upload the Smart Sensor data automatically to the Smart Sensor portal. The gateway needs to be configured for Internet access before it can start reading the Smart Sensors. This gateway uses 3G/4G Mobile network with the included USB dongle for internet connection. -
Page 5: Installation
2 – Installation 2.1 Prerequisites for installation Internet connection: Mobile network needs to have adequate signal strength. AC – Access Controller • Global: gw.smartsensor.abb.com Smart Sensor Platform • Global: smartsensor.abb.com Power supply: 110/115 vac grounded outlet to accept P0E injector power cord. -
Page 6: Obtaining The Correct Sim Card
A B B A B I L I T Y S M A R T S E N S O R B L U E T O O T H AT T- V Z N S I M C A R D R E A DY G AT E WAY I N S TA L L AT I O N M A N U A L —... -
Page 7: Gateway Configuration
IN STALL ATI ON — 2 – Installation 2.5 Gateway configuration When the gateway is powered on, the blue LED at the bottom of the gateway turns ON. After bootup, the gateway will turn on the configuration WIFI hotspot. The bootup takes about 30-60 seconds. Configuration WIFI hotspot has SSID “cassia-XXXXXX”, where XXXXXX is the last 6 digits of the gateway’s MAC address. - Page 8 2 – Installation Status page The Basic Page is where the configuration is done. Following values are needed: • AC Server Address: gw.smartsensor.abb.com • Remote Assistance: ON • Router Mode: AC Managed Router • AC Router Comm. Ports: 5246, 5247...
- Page 9 IN STALL ATI ON — 2 – Installation Basic page...
-
Page 10: At&T Mobile Network Configuration
A B B A B I L I T Y S M A R T S E N S O R B L U E T O O T H AT T- V Z N S I M C A R D R E A DY G AT E WAY I N S TA L L AT I O N M A N U A L —... -
Page 11: Verizon Mobile Network Configuration
IN STALL ATI ON — 2 – Installation 2.7 Verizon mobile network configuration The following items are required for Verizon mobile • Type or confirm Device: /dev/ttyACM0 • Select Peer DNS: 1 network configuration: • PROCET PoE injector as the power supply Press Apply at the bottom of the screen. -
Page 12: Gateway Configuration Confirmation
2 – Installation 2.8 Gateway configuration confirmation Confirm gateway is connected properly by contacting Smart Sensor support: • By email in the US: us-mptsensortechsupport@abb.com • By phone in the US: +864-284-5700 Ext 6 • Email outside US: support.smartsensor@abb.com You should see data moving automatically from your smart sensors in range of your gateway to the Smart... -
Page 13: Troubleshooting
TROUBLESHOOT ING — 3 – Troubleshooting For AT&T configuration: If 10569.MCS APN does not work, please try the APN: m2m.com.attz For Verizon configuration: If VZWINTERNET APN does not work, please try the APN: wyleslte.gw7.vzwentp... - Page 14 A B B A B I L I T Y S M A R T S E N S O R B L U E T O O T H AT T- V Z N S I M C A R D R E A DY G AT E WAY I N S TA L L AT I O N M A N U A L...
- Page 16 — ABB Motors and Mechanical Inc. 5711 R.S. Boreham, Jr. Street Fort Smith, AR 72901 Ph: 1.479.646.4711 new.abb.com/motors-generators...