Sealey PTB91508 Quick Start Manual

Thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear protective
instructions gloves
1. safeTy
‰ warNING! ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using these units.
‰ ‰
‰ locate the units in a suitable work area.
9 ‰
‰ Keep the work area clean, uncluttered and ensure there is adequate lighting.
9 ‰
‰ warNING! Use the units on level and solid ground, preferably concrete.
‰ ‰
‰ Keep the units clean and tidy in accordance with good workshop practice.
9 ‰
‰ Keep children and unauthorised persons away from the work area.
9 ‰
‰ Do NoT use these units for any purpose other than that for which they are designed.
8 ‰
‰ Do NoT use the units outdoors.
8 ‰
‰ Do NoT place the units in a damp or wet location or an area where there is condensation.
8 ‰
‰ Do NoT clean the units with any solvents which may damage the surfaces or the protective coating.
8 ‰
‰ Do NoT move the units with the drawers out. To avoid tipping, open one drawer at a time and close and secure all drawers whilst
8 ‰
moving.
‰ Do NoT step on the drawers.
8 ‰
2. INTroDucTIoN
Heavy-duty all welded steel construction for strength and durability. Textured powder coat finish which is solvent and rust resistant.
Ball bearing drawer runners provide superior performance and carry heavier loads, double sets on large drawers.
All drawers have full width sand blasted aluminium lift latch drawer pulls, making easy access and prevention of inadvertent opening when
box is being moved. Heavy-duty Ø125mm Mag style castors, 2 swivel with toe brakes and 2 fixed. Heavy-duty exterior handles on chest and
cabinets. Topchests feature gas struts on lids for easy opening. non-slip drawer liners supplied for all drawers. Rollcabs supplied with 12mm
PVC coated MdF worktop. Integral locking system locks all drawers in each unit with the turn of 1 key. All supplied with 2 keys. Manufactured to
the highest levels of construction to withstand the toughest of workshop/garage conditions.
3. specIfIcaTIoN
Model no: ...........................................................................PTB91508 ............................................................... PTB93006
overall Size (W x d x H): .................................... 915 x 450 x 565mm ...............................................930 x 460 x 1050mm
Medium 1/2 drawer (x6): ....................................... 385 x 385 x 60mm ........................................................................... n/a
Medium drawer (x3): ......................................................................n/a ...................................................825 x 385 x 60mm
Medium drawer (x2): ............................................. 825 x 385 x 60mm ........................................................................... n/a
large drawer (x2): .........................................................................n/a .................................................825 x 385 x 135mm
X-large drawer (x1): ......................................................................n/a .................................................825 x 385 x 210mm
4. assembly
4.1. These units are heavy, obtain the help of at least one other person before attempting to unpack them.
4.2. INsTall haNDle (refer To fIG.1).
4.2.1. Position the holes and attach with the bolts provided. Tighten securely.
© Jack Sealey limited
TopchesT 8 Drawer 915mm heavy-DuTy/
rollcab 6 Drawer 930mm heavy-DuTy
pTb91508 & pTb93006
Model no:
fig.1
Original Language Version
fig.2
PTB91508, PTB93006 Issue 1 (HF) 18/03/19