Sealey PTB66004SS Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear
instruction protective
manual gloves
1. SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using these units.
‰
Locate the units in a suitable work area.
9
Keep the work area clean, uncluttered and ensure there is adequate lighting.
9
WARNING! Use the units on level and solid ground, preferably concrete.
‰
Keep the units clean and tidy in accordance with good workshop practice.
9
Keep children and unauthorised persons away from the work area.
9
DO NOT use these units for any purpose other than that for which they are designed.
8
DO NOT use the units outdoors.
8
DO NOT place the units in a damp or wet location or an area where there is condensation.
8
DO NOT clean the units with any solvents which may damage the surfaces or the protective coating.
8
8 8 DO NOT move the units with the drawers out. To avoid tipping, open one drawer at a time and close and secure all drawers whilst
8 8
moving.
8 8 DO NOT step on the drawers.
8 8
2. INTRODUCTION
Heavy-duty welded steel construction for strength and durability. Anti fingerprint stainless steel finish, both solvent and rust resistant. Ball bearing drawer
slides provide superior performance and carry heavier loads, double sets on large drawers. All drawers have full width sand blasted aluminium 'Lift & Latch'
drawer pulls, making easy access while preventing inadvertent opening when box is being moved. Heavy-duty exterior side handles. Supplied with non-
slip drawer liners fitted to each drawer. Gas struts fitted to lid makes opening easy. Integral locking system locks all drawers with the turn of a key. Supplied
with 2 keys. Use with Model No. PTB67506SS Rollcab or can be a stand alone unit.
3. SPECIFICATION
Model No:
Overall Size WxDxH (mm):
Medium Drawer (x3):
Large Drawer (x1):
4. ASSEMBLY
4.1. These units are heavy, obtain the help of at least one other person before attempting to unpack them.
4.2. INSTALL HANDLE (refer to fig.1).
4.2.1. Position the holes on the rollcab and attach with the bolts provided. Tighten securely.
4.3. INSTALL WHEELS (ROLLCABS) (refer to fig.2).
4.3.1. Carefully lay rollcab on its back, with a soft mat underneath for protection. Install the two braked casters on the same end as the
handle.
4.3.2. Insert the carriage bolts through washers, then through the casters and into the bottom of the cabinet. Tighten securely.
4.3.3. Install the fixed wheels on the opposite end to the handle.
Original Language Version
© Jack Sealey Limited
INSTRUCTIONS FOR:
TOPCHEST 4 DRAWER 675MM HEAVY-DUTY/
ROLLCAB 6 DRAWER 675MM HEAVY-DUTY
MODEL No'
Indoor use
only
PTB66004SS Model No:
675 x 460 x 565 Overall Size WxDxH (mm):
560 x 385 x 60 Medium Drawer (x3):
560 x 385 x 135 Large Drawer (x2):
X-Large Drawer (x1):
PTB66004SS, PTB67506SS
s:
PTB67506SS
675 x 460 x 1030
560 x 385 x 60
560 x 385 x 135
560 x 385 x 210
fig.1
PTB66004SS, PTB67506SS
fig.2
Issue: 3 (H,2,3,F) 05/06/19