Mitsubishi MOTORS SHOGUN SPORT Owner's Manual

Table of Contents

Quick Links

Download this manual

SHOGUN SPORT

OWNER'S MANUAL

SHOGUN SPORT - EN-UK - 17MY OKWE17E1

Table of Contents

Chapters

Table of Contents

Need help?

Do you have a question about the SHOGUN SPORT and is the answer not in the manual?

Questions and answers

Summary of Contents for Mitsubishi MOTORS SHOGUN SPORT

Page 1 SHOGUN SPORT OWNER’S MANUAL SHOGUN SPORT - EN-UK - 17MY OKWE17E1...
Page 2 This manual explains operation of LHD and RHD vehicles. Illustra- tions represent LHD operation. Depending on the item, however, RHD illustrations may also appear. This vehicle is manufactured by Mitsubishi Motors (Thailand) Co, Ltd. in Thailand under license from Mitsubishi Motors Corporation. ©2016 Mitsubishi Motors Corporation...
Page 3 If you are aware that you will be operating your vehicle in conditions of circa: -10 ‫ ﹾ‬Centigrade or below on a regular basis we recommend the fitment of a fuel line heater. Your local Mitsubishi Motors dealership will be able to assist you with this.
Page 4 Table of contents Overview/Quick guide General information Locking and unlocking Seat and seat belts Instruments and controls Starting and driving For pleasant driving For emergencies Vehicle care Maintenance Specifications Alphabetical index...
Page 5 Instruments and Controls (Driver’s area) Instruments and Controls (Driver’s area) E08500101710 Combination headlamps and dipper switch P.5-57 Multi Around Monitor operation switch* P.6-134 Audio remote control switches* P.7-34 Turn-signal lever P.5-62 Front fog lamp switch* P.5-63 Horn switch P.5-70 Rear fog lamp switch* P.5-64 Supplemental restraint system (SRS) - airbag Headlamp washer switch* P.5-69 (for driver’s seat) P.4-30, 4-35...
Page 6 Instruments and Controls Instruments and Controls E08500101723 Air conditioner* P.7-2 Audio* P.7-22 Front cooler* P.7-6 Smartphone Link Display Audio*, Mitsubishi Multi-Commu- nication System*, DISPLAY AUDIO* Hazard warning flasher switch P. 5-63 Refer to the separate owner’s manual Ignition switch* P.6-17 Rear window demister switch P.5-69 Centre ventilators P.7-3 Fuses P.10-22...
Page 7 Instruments and Controls Audio* P.7-22 Rear window demister switch P.5-69 DISPLAY AUDIO*, Mitsubishi Multi Entertainment System* Front passenger’s airbag indicator* P.4-31, 4-33 Refer to the separate owner’s manual Cigarette lighter* P.7-87 Accessory socket* P.7-87 Air conditioner* P.7-2 Front cooler* P.7-6 Steering wheel height and reach adjustment lever Hazard warning flasher switch P.
Page 8 Instruments and Controls 8A/T 2WD 8A/T 4WD Off Road mode switch* P.6-60 Electric parking brake switch P.6-8 Hill Descent Control switch* P.6-78 Cup holder P.7-94 Electric parking Ashtray* P.7-86 brake switch P.6-8 Ashtray* P.7-86 Cup holder P.7-94 Super select 4WD II P.6-50 5M/T 6M/T, 5A/T Super select 4WD*...
Page 9 Interior Interior E08500201476 7 persons Seat belts P.4-14 Front room & map lamps P.7-88, 7-90, 10-29 Adjustable seat belt anchor P.4-16 Sunglasses holder* P.7-91, 7-93 Rear entertainment system* Sunroof* P.3-26 Refer to the separate owner’s manual Inside rear-view mirror P.6-13 Door courtesy lamps P.7-88, 7-91 Sun visors P.7-85 Supplemental restraint system (SRS)-...
Page 10 Interior 5 persons Seat belts P.4-14 Front room & map lamps P.7-88, 7-90, 10-29 Adjustable seat belt anchor P.4-16 Sunglasses holder* P.7-91, 7-93 Sunroof* P.3-26 Rear personal lamps Inside rear-view mirror P.6-13 P.7-88, 7-90, 10-29 Rear entertainment system* Refer to the separate owner’s manual Sun visors P.7-85 Supplemental restraint system (SRS)- curtain airbag* P.4-30, 4-38...
Page 11 Luggage area Luggage area E08500301217 Jack P.8-7 Tools P.8-7 Luggage hooks P.7-97 Fire extinguisher* Luggage floor boxes* P.7-91, 7-93 Warning triangle* First-aid kit* Warning triangle* Overview/Quick guide...
Page 12 Exterior - front Exterior - front E08500401928 Outside rear-view mirrors P.6-14 Sunroof* P.3-26 Side-view camera* P.6-133 Roof antenna* P.7-57 Fuel tank filler door P.2-3 Wiper and washers P.5-64, 10-20 Locking and unlocking P.3-15, 3-16 Keyless entry system P.3-4 Bonnet P.10-4 Keyless operation system* P.3-7 Engine compartment P.10-2, 11-11 Security alarm system* P.3-20...
Page 13 Exterior - rear Exterior - rear E08500401931 Reversing lamps P.10-28, 10-33 Rear turn-signal lamps P.5-62, 10-28, 10-33 Tail and stop lamps P.5-57, 10-28, 10-33 High-mounted stop lamp P.10-28 Blind Spot Warning lamp* P.6-116 Glass antenna* P.7-58 Rear wiper and washer P.5-68 Tailgate P.3-18 Rear-view camera* P.6-129, 6-133 Multi around monitor* P.6-133...
Page 14 Quick guide Refer to “Keyless entry system” on page Quick guide Driver’s or front passenger’s door lock/unlock 3-4. switches E08500500010 For vehicles equipped with the mirror retrac- tor switch, the outside rear-view mirrors can Lock and unlock the doors be folded and extended automatically if you press the LOCK switch (1) or UNLOCK E08500601438 switch (2).
Page 15 Quick guide 1-Electric remote-controlled out- 2-Engine switch Around the driver’s seat side rear-view mirrors E08500801485 [For vehicles equipped with the keyless oper- ation system] To adjust the mirror position If you are carrying the keyless operation key, you can start the engine. If you press the engine switch without depressing the brake Except for vehicles pedal (A/T) or the clutch pedal (M/T), you...
Page 16 Quick guide 3-Combination headlamps 3-Turn-signal lever Type 2 Rotate the switch to turn on the lamps. The turn-signal lamps flash when the lever is operated. Type 1 All lamps off With the ignition switch or the operation mode is in ON, head- 1- Turn-signals lamps, position, tail, licence plate 2- Lane-change signals...
Page 17 Quick guide 5-Wiper and washer switch Type 2 Type 1 A- Locked B- Release MIST- Misting function The wipers will operate once. Refer “Steering wheel height and reach OFF- adjustment” on page 6-13. MIST- Misting function AUTO- Auto-wiper control The wipers will operate once. Rain sensor OFF- Off The wipers will automatically...
Page 18 Quick guide 6-Electric window control 7-Fuel tank filler door release lever Press the switch down for opening the win- dow, and pull the switch for closing. Open the fuel tank filler door. The fuel tank filler is located on the rear left side of your vehicle.
Page 19 Quick guide Selector lever positions 8-Speed automatic transmission WARNING with sports mode  If the lock button is always pushed to operate the selector lever, the lever may be “P” PARK E08501001341 accidentally shifted into the “P” (PARK) or “R” (REVERSE) position. Be sure not This position locks the transmission to pre- Selector lever operation to push the lock button when performing...
Page 20 Quick guide Refer to “8-speed automatic transmission with sports mode” on page 6-39. 4-wheel drive operation E08502000048 Road conditions Driving mode Dry paved road Packed snow Deep snow or Gravel road Sandy road Rocky road and highway road muddy road Super select 4WD (...
Page 21 Quick guide 4- Forward Collision Mitigation System Multi information display Type 2 (FCM) and Ultrasonic misacceleration E08501201239 Mitigation System (UMS) OFF indica- Always stop the vehicle in a safe place before tor display*  P.6-102, 6-109 operating. 5- Cruise control indicator display* The following information is included on the ...
Page 22: Table Of Contents
General information Fuel selection ...................2-2 Filling the fuel tank ................2-3 Installation of accessories ..............2-5 Modification/alterations to the electrical or fuel systems ....2-5 Genuine parts ...................2-6 Used engine oils safety instructions ..........2-6...
Page 23: Fuel Selection
Fuel selection Fuel selection CAUTION CAUTION  Diesel-powered vehicles with the “DIESEL  Do not use more than 10 % concentration of E00200104839 EN590” or the “DIESEL Euro IV-PH” label ethanol (grain alcohol) by volume. Petrol-powered vehicles on the fuel tank filler door are designed to Use of more than 10 % concentration may Unleaded petrol octane number use only diesel fuel that meets the EN590 or...
Page 24: Filling The Fuel Tank
Be sure dition. Be sure to use a MITSUBISHI you and that person was carrying static to use a MITSUBISHI MOTORS GENUINE MOTORS GENUINE DIESEL FUEL SYS- electricity, fuel vapor could be ignited.
Page 25 Filling the fuel tank Fuel tank capacity NOTE  While filling with fuel, hang the fuel cap on the hook (A) located on the inside of the fuel Petrol-powered vehicles:70 litres tank filler door. Diesel-powered vehicles:68 litres Refueling 1. Before filling with fuel, stop the engine. 2.
Page 26: Installation Of Accessories
Modification/alterations to documents accompanying this vehicle. only for MITSUBISHI MOTORS but also an the electrical or fuel systems Only MITSUBISHI MOTORS approved authorised MITSUBISHI MOTORS dealer,...
Page 27: Genuine Parts
MITSUBISHI MOTORS GENUINE PARTS. CAUTION At the MITSUBISHI MOTORS dealer you  Please consult an authorised MITSUBISHI can also get appropriate advice and the MOTORS dealer concerning any such fit- assembling of Genuine Parts will be handled ment or modification.
Page 28 Locking and unlocking Keys ....................3-2 Key number tag ................3-2 Electronic immobilizer (Anti-theft starting system) ......3-3 Keyless entry system ...............3-4 Keyless operation system* ...............3-7 Doors ....................3-15 Central door locks ................3-16 “Child-protection” rear doors ............3-17 Tailgate ..................3-18 Security alarm system*..............3-20 Electric window control ..............3-24 Sunroof* ..................3-26...
Page 29: Keys
MITSUBISHI MOTORS dealer in  The engine is designed so that it will not start plane. If a switch is pressed on the plane, if the ID code registered in the immobilizer the event the original keys are lost.
Page 30: Electronic Immobilizer (Anti-Theft Starting System)
 If you lose one of them, contact an author- bilize the vehicle if an invalid start is ised MITSUBISHI MOTORS dealer as soon attempted. A valid start attempt can only be as possible. To obtain a replacement or extra achieved, using a key “registered”...
Page 31: Keyless Entry System
For further information, please contact an Press the LOCK switch (1). All the doors and tions could cause failure of the immobilizer. authorised MITSUBISHI MOTORS dealer. the tailgate will be locked. The turn-signal • The time for automatic relocking can be lamps will blink once.
Page 32 For further information, please contact an  Functions can be modified as stated below. switch is pressed again twice in a row authorised MITSUBISHI MOTORS dealer. Please consult an authorised MITSUBISHI within approximately 30 seconds, the out- If you replace the battery yourself, refer to MOTORS dealer.
Page 33 + side NOTE - side  You may purchase a replacement battery at an electric appliance store. Coin type  An authorised MITSUBISHI MOTORS battery dealer can replace the battery for you if you CR1620 prefer. Keyless operation key 1. Remove the screw (A) from the key.
Page 34: Keyless Operation System
Please consult an brillators should not go near the exterior authorised MITSUBISHI MOTORS dealer. transmitters (A) or the interior transmit- ters (B). The radio waves used by the key- less operation system could adversely affect implantable cardiac pacemakers or implantable cardiovascular-defibrillators.
Page 35 MITSUBISHI MOTORS dealer. the key is near to the ground or high up, the Refer to “Procedure for replacing the key E00306201685 system may not operate.
Page 36 Keyless operation system* gate LOCK switch (B) within the operating To operate using the keyless range, the doors and the tailgate are locked. operation function The turn-signal lamps will blink once. Also refer to “Locking and unlocking: Doors, E00305802317 Central door locks, Tailgate” on pages 3-15, Driver's or front passenger's door lock/unlock 3-16 and 3-18.
Page 37  Functions can be modified as stated below. • The operation mode is not in OFF. For further information, please contact an authorised MITSUBISHI MOTORS dealer.  The time between unlocking and automatic locking can be adjusted. Please consult an •...
Page 38 Keyless operation system* 2- Unlock Locking and unlocking the door Turning the emergency key in the forward direction locks the door, and turning it in the rear direction unlocks the door. Also refer to “Locking and unlocking: Doors” on page 3-15.
Page 39 Keyless operation system* TYPE 1 TYPE 2 Item Note (Solution) Display Buzzer Indicator Buzzer Fall of battery Inner buzzer No sounds The battery starts to run out, the warning is activated. （The voltage sounds once warning is not activated if the battery is completely dead.） Blinks Key not Inner buzzer...
Page 40 For further information, please contact an authorised MITSUBISHI MOTORS dealer. • Even if you have the keyless operation key within the...
Page 41 Keyless operation system* TYPE 1 TYPE 2 Item Note (Solution) Display Buzzer Indicator Buzzer Key lock-in Inner buzzer Outer buzzer • When the operation mode is in OFF, if you close all the prevention sounds once sounds doors and the tailgate with the keyless operation key left in system Outer buzzer approxi-...
Page 42: Doors
Doors 2- Unlock Doors NOTE  The driver’s door can be opened without E00300403621 NOTE using the lock knob by pulling on the inside CAUTION  When locking or unlocking with the key, all door handle. doors and the tailgate will be locked or ...
Page 43: Central Door Locks
Central door locks Central door locks E00300803263 NOTE  Repeated continuous operation between lock and unlock could activate the central door locking systems built-in protection circuit and prevent the system from operating. If this occurs, wait approximately 1 minute before operating the central door lock sys- tem.
Page 44: Child-Protection" Rear Doors
MITSUBISHI at an authorised MITSUBISHI MOTORS MOTORS dealer. dealer immediately. • The door does not lock automatically Unlock using the ignition even when the vehicle speed exceeds switch, the engine switch or the approximately 9 mph.
Page 45: Tailgate
Tailgate CAUTION WARNING  When driving with a child in the rear seat,  When there is a build up of snow or ice, it please use the child protection to prevent should be removed before opening the tail- accidental door opening which may cause an gate.
Page 46 Tailgate To close To close the tailgate, pull the tailgate grip (A) downward and release it before the tailgate is completely closed, then gently push shut the tailgate from the outside. 2. Move the lever (B) to open the tailgate. NOTE ...
Page 47: Security Alarm System
Security alarm system* The system preparation time extends from the NOTE CAUTION point at which all of the doors and the tailgate  Gas struts (B) are installed to support the  Do not modify or add parts to the security are locked by pressing of the LOCK switch tailgate.
Page 48 Security alarm system* Alarm activation NOTE  When lending the vehicle to another person or allowing the vehicle to be driven by some- Inside alarm (approximately 10 seconds): one who is unfamiliar with the security alarm The buzzer sounds, warning those inside system, be sure to give the person a proper explanation of the security alarm system.
Page 49 Have the vehicle inspected at an authorised  Pressing the UNLOCK switch on the key. MITSUBISHI MOTORS dealer.  Turning the ignition switch to the “ON” position. (vehicles with keyless entry sys- tem) ...
Page 50  Putting the operation mode in ON. (vehi- Replace the battery at your authorised MITSUBISHI MOTORS dealer. cles with keyless operation system)  If the UNLOCK switch on the key, or the  Holding the keyless operation key and driver’s...
Page 51: Electric Window Control
Electric window control If you want to stop the window movement, Electric window control WARNING operate the switch lightly in the reverse direc-  Before operating the electric window con- E00302201658 tion. trol, make sure that nothing is capable of The electric windows can only be operated being trapped (head, hand, finger, etc.).
Page 52 Electric window control Lock switch Timer function CAUTION  The safety mechanism is cancelled just E00303102446 E00302402110 before the window is fully closed. This When this switch is operated, the passenger’s The door windows can be opened or closed allows the window to close completely. switches cannot be used to open or close the for 30 seconds after the engine is stopped.
Page 53: Sunroof
Sunroof* 2- Tilt up NOTE Safety mechanism 3- Close, Tilt down  If the battery terminals are disconnected or E00303801420 the fuse for electric window is replaced, the To open, press the switch (1). If a hand or head is trapped in the closing safety mechanism will be cancelled and the To stop the moving sunroof, press the switch sunroof, it will re-open automatically.
Page 54 MITSUBISHI MOTORS dealer. 4. Following this action, it should be possi-  Depending on the models of ski carriers or ble to operate the sunroof in the normal roof carriers, the sunroof may contact with manner.
Page 55 Sunroof* NOTE  The sunshade will operate together with the sunroof when the sunroof is opened.  Be sure to tilt down the sunroof before clos- ing the sunshade. 3-28 Locking and unlocking...
Page 56 Seat and seat belts Seat arrangement ................4-2 Seat adjustment ................4-4 Front seats ..................4-4 Second seats ..................4-5 Third seats (7 persons) ..............4-6 Head restraints .................4-7 Making a luggage area ..............4-9 Making a flat seat ................4-13 Seat belts ..................4-14 Pregnant women restraint ..............4-19 Seat belt pre-tensioner system and force limiter system ....4-19 Child restraint ................4-20 Seat belt inspection ................4-30...
Page 57: Seat Arrangement
Seat arrangement Seat arrangement E00400202027 By operating the front, second or third seat, select the desired seat arrangement. Seat and seat belts...
Page 58 Seat arrangement 5 persons 7 persons Normal usage Flat seat  P.4-13 Folding the second seats  P.4-9 Folding the third seat- Making a luggage backs forward — area  P.4-11 Folding the third seats —  P.4-12 Seat and seat belts...
Page 59: Seat Adjustment
Seat adjustment Seat adjustment WARNING CAUTION  To minimize the risk of personal injury in  When sliding or reclining the seat rearward, E00400301962 the event of a collision or sudden braking, pay careful attention to the rear seat passen- Adjust the driver’s seat so that you are com- the seatbacks should always be in the gers.
Page 60: Second Seats
Second seats 3- To adjust seat cushion height (driver’s 4- To adjust seat cushion angle CAUTION side only)* Operate the switch as indicated by the  The reclining mechanism of the seatback is Turn the dial and adjust the seat cush- arrows and adjust the seat cushion spring loaded, causing it to return to the ver- ion height to the desired position.
Page 61: Third Seats (7 Persons)
Third seats (7 persons) CAUTION  For reasons of safety, do not sit in the third seat when using the tether anchor strap (Type 2 only). Refer to “Installing a child restraint system to the lower anchorage (ISOFIX child restraint mountings) and tether anchorage” on page 4-26.
Page 62: Head Restraints
Head restraints in the direction of the arrow. After adjust- Head restraints Second seats ment, push the head restraint downward and E00403302885 make sure that it is locked. WARNING  Driving without the head restraints in place can cause you and your passengers serious injury or death in an accident.
Page 63 Head restraints WARNING To install  When a person sits in the second or the third seats (7 persons), pull up the head Confirm that the head restraint is facing the restraint to a height at which it locks in correct direction, and then insert it into the position.
Page 64: Making A Luggage Area
Making a luggage area CAUTION  When folding or storing the seat, be sure not to catch your hand or leg. NOTE  It is possible to folding the seat indepen- dently on each side. Folding the second seats 5. Lift the whole seat forward. E00403801203 Making a luggage area To fold...
Page 65 Making a luggage area CAUTION  Do not allow any person to sit on the folded seat, and do not place luggage on it. The seat’s mounting fittings could bend under the weight, making it impossible for the seat to be retained on the vehicle.
Page 66 Making a luggage area Push lightly on the seatback to confirm that it has actually been secured. 4. Pull the seatback lock release band (B), then tilt the seatback forward until you Folding the third seatbacks for- hear a “click”. 2.
Page 67 Making a luggage area Folding the third seats (7 per- sons) E00403901116 To fold 1. Fold the second seats. (Refer to “Folding the second seats” on page 4-9.) 2. Lower the head restraints of the third seat to the lowest position. (Refer to “Head restraints”...
Page 68: Making A Flat Seat
Making a flat seat CAUTION  To ensure the seats are locked securely, attempt to move them back and forth.  Do not jump on, or impact the seatbacks heavily.  To raise the seatback, put a hand on the seat- back and raise slowly.
Page 69: Seat Belts
Seat belts 2. Slide the front seats fully forward, then tip The front seat belts have a pre-tensioner sys- CAUTION their seatbacks backward. tem. These belts are used the same way as a  Since the gap is made between the seatbacks Refer to “Front seats”...
Page 70 Seat belts 3. Pull the belt slightly to adjust slackness as To fasten WARNING desired.  No modifications or additions should be 1. Pull the seat belt out slowly while holding made by the user which will either prevent the latch plate. NOTE the seat belt adjusting devices from oper- ating to remove slack, or prevent the seat...
Page 71 Seat belts Seat belt reminder WARNING  Do not install any accessory or sticker that E00409802332 makes the lamp difficult to see. Type 1 NOTE  If the seat belt subsequently remains unfas- tened, the warning lamp and the tone will issue further warnings each time the vehicle starts moving from a stop.
Page 72 Seat belts 1- Tighten WARNING WARNING 2- Loosen  When adjusting the seat belt anchor, set it  Be sure to securely connect the both latch at a position that is sufficiently high so plate (A and B). Failing to do so could sig- While holding the latch plate, insert the latch that the belt will make full contact with nificantly reduce the amount of protection...
Page 73 Seat belts 5. Pull the belt slightly to adjust slackness as desired. To unfasten 1. Hold the latch plate and press the button on the buckle. NOTE  As the belt retracts automatically, keep the latch plate held while retracting so that the belt stows slowly.
Page 74: Pregnant Women Restraint
Pregnant women restraint Pregnant women restraint Centre seating position (3-point type seat belt)* E00405600064 Refer to “Second-centre 3-point type seat WARNING belt” on page 4-17.  Seat belts work for everyone, including pregnant women. Pregnant women should Seat belt buckle storage use the available seat belts.
Page 75: Child Restraint
 If you need to scrap the vehicle, please con- sult an authorised MITSUBISHI MOTORS Child restraint dealer. It is important to do so because unex- pected activation of the pre-tensioner seat E00406403608 belts could cause injuries.
Page 76 Child restraint Caution for installing the child WARNING Infants and small children restraint on vehicle with front  A REARWARD FACING CHILD E00406602300 RESTRAINT must NOT be used in the passenger airbag When transporting infants and small children front passenger seat as it places an infant in your vehicle, follow the instruction given too close to the passenger airbag.
Page 77 Child restraint  Before purchasing a child restraint sys- NOTE tem, try installing it in the rear seat to  Depending on the seating position in the make sure there is a good fit. Because of vehicle and the child restraint system that the location of the seat belt buckles and you have, the child restraint can be attached the shape of the seat cushion, it may be...
Page 78 Child restraint Suitability for various ISOFIX positions E00411402003 Vehicle ISOFIX positions Mass Group Size class Fixture Second Outboard carrycot ISO/L1 ISO/L2 -Up to 10 kg ISO/R1 -Up to 13 kg ISO/R1 ISO/R2 ISO/R3 -9 to 18 kg ISO/R2 ISO/R3 ISO/F2 ISO/F2X ISO/F3 II &...
Page 79 Child restraint Key of characters to be inserted in the above table:  IUF- Suitable for ISOFIX forward child restraint systems of universal category approved for use in the mass group.  X- ISOFIX position not suitable for ISOFIX child restraint systems in this mass group. Suitability for various seating positions E00406802777 Seating Position...
Page 80 Child restraint Key of characters to be inserted in the above table:  U- Suitable for “universal” category restraints approved for use in this mass group.  UF- Suitable for forward facing “universal” category restraints approved for use in this mass group. ...
Page 81 Child restraint securing a child restraint system tether strap Installing a child restraint sys- to each of the 2 rear seating positions in your tem to the lower anchorage vehicle. (ISOFIX child restraint mount- ings) and tether anchorage E00408902176 Lower anchorage location Your vehicle’s rear seat is fitted with lower anchorages for attaching a child restraint sys- CAUTION...
Page 82 Child restraint Type 1 A: Child restraint system connectors If your child restraint system with a tether strap, perform the step 4 through 6. If your child restraint system without a tether To install strap, perform the step 6. 1. Remove any foreign material in or around Type 2 the connectors and ensure the vehicle seat 4.
Page 83 Child restraint 3. To activate the ALR mode, slowly pull the NOTE shoulder part of the belt all the way out  If it is difficult to latch the tether strap hook, until it stops, then let the belt feed back turn the hook sideways.
Page 84 Child restraint To remove CAUTION  Do not sit in the left side of the second seat 1. Remove the plate from the buckle, then when installing a child restraint system to the remove the seat belt from the child middle seating position of the second seat.
Page 85: Seat Belt Inspection
MITSUBISHI MOTORS dealer. Failure to have an authorised MITSUBISHI MOTORS dealer perform the work could reduce the effectiveness of the belts and  A dirty belt should be cleaned with neu- could result in serious injury in the event tral detergent in warm water.
Page 86 Supplemental restraint system (SRS)-airbag The SRS driver’s and front passenger’s air- occupants, including the passengers as well 5 persons bags are designed to supplement the primary as the driver, must wear their seat belts. protection of the driver and front passenger side seat belt systems by providing those How the supplemental restraint occupants with protection against head and...
Page 87 Supplemental restraint system (SRS)-airbag [Vehicles equipped with the keyless operation WARNING system]  IT IS VERY IMPORTANT TO BE PROP- The operation mode is in ON. ERLY SEATED. The airbags deployment produces a sudden, A driver or front passenger too close to loud noise, and releases some smoke and the steering wheel or instrument panel powder, but these conditions are not injuri-...
Page 88 Supplemental restraint system (SRS)-airbag that cannot be fitted to any seat other than the front passenger seat, be sure to turn OFF the front passenger’s airbag ON-OFF switch before using it. (Refer to “To turn an airbag off” on page 4-34) Front passenger’s airbag ON-OFF switch is located as shown in the illustration.
Page 89 • Always turn the ignition switch to the the system inspected by an authorised “LOCK” position or put the operation MITSUBISHI MOTORS dealer. mode in OFF, before operating the front • If the OFF indicator remains on when passenger’s airbag ON-OFF switch. Fail- the front passenger’s airbag ON-OFF...
Page 90 Supplemental restraint system (SRS)-airbag Deployment of front airbags and driver’s knee airbag E00407502856 The front airbags and driver’s knee airbag ARE DESIGNED TO DEPLOY when… The front airbags and driver’s knee airbag are designed to deploy when the vehicle suffers a The front passenger’s airbag is now deacti- moderate to severe frontal impact.
Page 91 Supplemental restraint system (SRS)-airbag The front airbags and driver’s knee airbag Because the front airbags and driver’s knee The front airbags and driver’s will deploy if the severity of impact is above airbag do not protect the occupant in all types knee airbag MAY NOT DEPLOY the designed threshold level, comparable to of frontal collisions, be sure to always prop-...
Page 92 Supplemental restraint system (SRS)-airbag of collisions, be sure to always properly wear Because the front airbags and driver’s knee your seat belts. airbag may deploy in certain types of unex- pected impacts as shown in the illustration that can easily move you out of position, it is The front airbags and driver’s important to always properly wear your seat knee airbag MAY DEPLOY...
Page 93 Supplemental restraint system (SRS)-airbag Side airbag system E00407601821 The side airbags (A) are contained in the driver and front passenger seatbacks. The side airbag is designed to inflate only on the side of the vehicle that is impacted, even with no passenger in the front seat. WARNING Curtain airbag system ...
Page 94 Supplemental restraint system (SRS)-airbag vehicle body. Examples of some typical con- 7 persons ditions are shown in the illustration. The seat belts in your vehicle are your pri- mary means of protection in a collision. The Deployment of side airbags and SRS side airbags and curtain airbags are 1- Side impacts in an area away from the curtain airbags...
Page 95 Supplemental restraint system (SRS)-airbag Because the side airbags and curtain airbags 5- Vehicle rolls onto its side or roof WARNING do not protect the occupant in all types of col-  Do not allow any rear seat occupant to Because the side airbags and curtain airbags lisions, be sure to always properly wear your hold onto the seatback of either front seat, do not protect the occupant in all types of side...
Page 96 Supplemental restraint system (SRS)-airbag WARNING SRS warning lamp/display 5 persons  Do not put a hanger or any heavy or E00407803090 pointed object on the coat hook. If the cur- tain airbag was activated, any such item Type 1 could be propelled away with great force and could prevent the curtain airbag from inflating correctly.
Page 97  If you found any tear, scratch, crack or damage to the portion where the airbag is stored, you should have the SRS inspected by an authorised MITSUBISHI MOTORS dealer. 4-42 Seat and seat belts...
Page 98 Instruments and controls Instruments ..................5-2 Multi information display - Type 1 ..........5-3 Multi information display - Type 2 ..........5-18 Indicator lamp, warning lamp, and information screen display list (multi information display - Type 1) ....5-26 Indicator and warning lamps (multi information display - Type 2) ..........5-50 Indicator lamps ................5-51 Warning lamps ................5-52 Information screen display (Vehicle equipped...
Page 99: Instruments
Instruments 2- Multi information display (Type 1: Instruments Meter illumination control - Color liquid crystal display type) → Type 1 P.5-3 E00500102812 Information screen display list (Type 1) E00531301116 Type 1 → P.5-28 Each time you press the rheostat illumination Multi information display (Type 2: button, there is a sound and the brightness of Mono-color liquid crystal display type)
Page 100: Multi Information Display - Type 1
Multi information display - Type 1 [When the ignition switch or the operation [When the ignition switch or the operation NOTE mode is OFF] mode is ON]  The brightness level of the instruments is stored when the ignition switch is turned off or the operation mode is put in OFF.
Page 101: Multi Information Display - Type 2
Multi information display - Type 1 8-Information screen  P.5-5 Information screen (when the 9-Selector lever position indicator display ignition switch or the operation (vehicles with 5A/T)  P.6-34 mode is OFF) (Vehicles with 8A/T)  P.6-41 10-Engine coolant temperature display E00520201955 ...
Page 102 Multi information display - Type 1 1- Tripmeter  P.5-8 Information screen (when the Information screen (when the 2- Tripmeter  P.5-8 ignition switch is turned from ignition switch or the operation 3- Driving range display  P.5-10 the “LOCK” position to the mode is ON) ECO drive assist display* ...
Page 103 Multi information display - Type 1 NOTE “ ”: Press lightly. To return to the screen displayed before the warning display “ ”: Press for approximately 2 seconds or  While driving, the function setting screen is not displayed even if you operate the multi more.
Page 104 Multi information display - Type 1 When the cause of the warning display is CAUTION Fuel remaining display eliminated, the mark goes out automati-  Before moving your vehicle, check that the E00522201702 cally. warning lamp is OFF. This displays the amount of fuel remaining. NOTE Engine coolant temperature ...
Page 105 Multi information display - Type 1 Fuel remaining warning display CAUTION NOTE  For petrol-powered vehicles, do not run out  Depending on factors such as the driving E00522402264 of fuel, or the catalytic converter may be conditions, the displayed temperature may When the fuel is reduced to approximately adversely affected.
Page 106 NOTE tion switch or the operation mode is in OFF. MITSUBISHI MOTORS. “---” is displayed when the inspection time has arrived. When the display is reset, the time until the  The distance is shown in units of 100 km next periodic inspection is displayed and the (100 miles).
Page 107  If you accidentally reset the display, we rec- drive). When the driving range falls below ommend you to consult an authorised approximately 50 km (30 miles), “---” is dis- MITSUBISHI MOTORS dealer. played. Refuel as soon as possible. 5-10...
Page 108 Multi information display - Type 1 The reset mode conditions for the average NOTE fuel consumption display can be switched  The memory of the auto reset mode or man- between “Auto reset” and “Manual reset”. ual reset mode for the average fuel consump- Refer to “Changing the reset mode for aver- tion display is erased if the battery is age fuel consumption and average speed”...
Page 109 Multi information display - Type 1 momentary fuel consumption is displayed NOTE with a green bar graph.  The average speed display can be reset sepa- ECO drive level Be conscious of maintaining the momentary rately for the auto reset mode and for the fuel consumption above the average fuel con- manual reset mode.
Page 110 Multi information display - Type 1 The display shows the overall ECO score the 2. Lightly press the multi information dis- function has counted from the time when the play switch a few times to switch the ignition switch is turned to “ON” to the time information screen to the function setting when it is turned to “LOCK”...
Page 111 Multi information display - Type 1 Refer to “Changing the temperature unit” Changing the reset mode for aver- Manual reset mode on page 5-15. age fuel consumption and average Refer to “Changing the display language”  When the average fuel consumption and speed on page 5-16.
Page 112 Multi information display - Type 1 5. Press and hold the multi information dis- NOTE Auto reset mode play switch for approximately 2 seconds  The memory of the auto reset mode or man- or more to change the setting to the ...
Page 113 Multi information display - Type 1 1. Press and hold the multi information dis- 1. Press and hold the multi information dis- 1. Press and hold the multi information dis- play switch for approximately 2 seconds play switch for approximately 2 seconds play switch for approximately 2 seconds or more to switch from the setting mode or more to switch from the setting mode...
Page 114 Multi information display - Type 1 1. Press and hold the multi information dis- 1. Press and hold the multi information dis- 2. Lightly press the multi information dis- play switch for approximately 2 seconds play switch for approximately 2 seconds play switch to select (changing or more to switch from the setting mode...
Page 115 Multi information display - Type 2 NOTE  The factory settings are as follows. • Average fuel consumption and average speed reset mode: A (Auto reset) • Fuel consumption display unit: L/100 km • Temperature unit: °C (Celsius) • Display language: ENGLISH •...
Page 116 Multi information display - Type 2 Information display E00528201355 Each time you lightly press the multi information display switch (A), the display switches in the following order. 1- Odometer  P.5-20 4- Meter illumination control  P.5-20 7- Outside temperature display*  P.5-21 5- Driving range display ...
Page 117 Multi information display - Type 2 Odometer NOTE NOTE  When disconnecting the battery terminal, the  You can adjust to 8 different levels respec- E00527801123 tively for when the position lamps are illumi- The odometer indicates the distance travelled. memory of tripmeter nated and when they are not.
Page 118 Multi information display - Type 2 NOTE NOTE NOTE  On rare occasions, the value displayed for  “---” is displayed when the average fuel con-  Depending on factors such as the driving the driving range may change if you are sumption cannot be measured.
Page 119 Multi information display - Type 2 flashes. If the remaining fuel level is reduced Engine coolant temperature further, the last segment of the fuel gauge display goes out and “ ” flash. E00533801098 1- Full 0- Empty This indicates the engine coolant tempera- ture.
Page 120 “---” to “cLEAr”. tion is due. Please consult an authorised NOTE After this, the time until the next periodic MITSUBISHI MOTORS dealer. inspection will be displayed. 3. After your vehicle is inspected at an  Depending on the vehicle specifications, the...
Page 121 Multi information display - Type 2 Changing the reset mode for aver- NOTE Manual reset mode age fuel consumption  “---” display cannot be reset when the igni- • When the average fuel consumption is tion switch or the operation mode is in ON. E00522902197 being displayed, if you hold down the ...
Page 122 Multi information display - Type 2 • When the engine switch or the operation also switched to match the selected fuel con- NOTE mode is in the following conditions, the sumption unit.  The display units for the driving range, the average fuel consumption display is average fuel consumption are switched, but 1.
Page 123: Indicator Lamp, Warning Lamp, And Information Screen Display List (Multi Information Display - Type 1)
Indicator lamp, warning lamp, and information screen display list (multi information display - Type 1) Refer to “Information display” on page NOTE 5-19.  The temperature value on air conditioner 2. Each time you press the multi information panel is switched in conjunction with outside display switch for 2 seconds or more on temperature display unit of the multi infor- outside temperature display, you can...
Page 124 Indicator lamp, warning lamp, and information screen display list (multi information display - Type 1) 4- High-beam indicator lamp  P.5-51 20- Speed warning lamp* P.5-55 5- Rear fog lamp indicator lamp* 21- Electric parking brake warning lamp P.5-51 (yellow) P.5-53 6- Rear differential lock indicator lamp* 22- Hill Descent Control indicator lamp* P.6-62...
Page 125 • An extremely strong electromagnetic wave is received from a source such as an illegal radio set, a spark from a wire, or a radar station. • Abnormal voltage or a static electricity discharge is generated by the operation of installed electrical equipment (including after-market parts). If the warning display appears many times, consult an authorised MITSUBISHI MOTORS dealer. Warning display list...
Page 126 Indicator lamp, warning lamp, and information screen display list (multi information display - Type 1) Screen Cause Solution (Reference)  There is a fault in the keyless operation Refer to “Keyless operation system” on page system. 3-7.  You turned the ignition switch to the “ON” ...
Page 127 5-8.  There is a fault in the fuel system.  Have your vehicle inspected at an author- ised MITSUBISHI MOTORS dealer.  You are driving with the parking brake still  Release the parking brake. Refer to “Brake applied.
Page 128 Refer to “Oil pressure warning display” on page 5-57.  It is suspected that the engine oil level has  Immediately have your vehicle checked by increased excessively. an authorised MITSUBISHI MOTORS dealer. Refer to “Engine oil level warning display” on page 5-57. Instruments and controls...
Page 129 Indicator lamp, warning lamp, and information screen display list (multi information display - Type 1) Screen Cause Solution (Reference)  An excessive amount of particulate matter Refer to “Diesel particulate filter (DPF)” on (PM) accumulates inside the diesel particu- page 6-28. late filter (DPF).
Page 130  There is a fault in the steering wheel lock.  Immediately stop the vehicle in a safe place and consult an authorised MITSUBISHI MOTORS dealer.  The steering wheel is locked.  Press the engine switch while turning steer- ing wheel.
Page 131 A/T” on page 6-43.  There is a fault in the A/T.  Have your vehicle inspected at an author- ised MITSUBISHI MOTORS dealer. Refer to “5-Speed automatic transmission with sports mode: When a malfunction occurs in the A/T” on page 6-36.
Page 132 Cause Solution (Reference)  There is a fault in the Super select 4WD II.  Have your vehicle inspected at an Author- ised MITSUBISHI MOTORS dealer. Refer to “Drive mode indicator display and 2WD/4WD operation indicator display” on page 6-56.
Page 133 ON.  There is a fault in the hill start assist.  Have your vehicle inspected at an Author- ised MITSUBISHI MOTORS dealer. Refer to “Warning lamp/display” on page 6-77.  There is a fault in the active stability &...
Page 134 Indicator lamp, warning lamp, and information screen display list (multi information display - Type 1) Screen Cause Solution (Reference)  The braking system temperature is too  Immediately stop the vehicle in a safe high. place. Refer to “ASTC indicator lamp or ASTC OFF indicator lamp”...
Page 135 Indicator lamp, warning lamp, and information screen display list (multi information display - Type 1) Screen Cause Solution (Reference)  The Adaptive Cruise Control System Refer to “How to use ACC” on page 6-95. (ACC) control is automatically cancelled.  Conditions for the start of control are not met, the Adaptive Cruise Control System (ACC) can not start the control.
Page 136 Mitigation System (FCM) has been 6-104. activated.  There is a fault in the Forward Collision  Have your vehicle inspected at an author- Mitigation System (FCM). ised MITSUBISHI MOTORS dealer. Refer to “FCM braking function” on page 6-104. Instruments and controls 5-39...
Page 137 Indicator lamp, warning lamp, and information screen display list (multi information display - Type 1) Screen Cause Solution (Reference)  The Forward Collision Mitigation System Refer to “FCM braking function” on page (FCM) is not available temporarily. 6-104.  Foreign matter such as dirt adheres to the Refer to “To terminate ACC control”...
Page 138 Indicator lamp, warning lamp, and information screen display list (multi information display - Type 1) Screen Cause Solution (Reference)  When the Forward Collision Mitigation Refer to “Forward Collision Mitigation Sys- System (FCM) is ON, if the rear differen- tem (FCM) and Ultrasonic misacceleration tial lock switch is set to ON, the FCM will Mitigation System (UMS) ON/OFF switch”...
Page 139 6-113.  The Ultrasonic misacceleration Mitigation  Immediately have your vehicle inspected at System (UMS) does not operate normally an authorised MITSUBISHI MOTORS because there are some malfunctions in the dealer. sensor or the system. Refer to “When there is a malfunction in the system or the sensor”...
Page 140 Indicator lamp, warning lamp, and information screen display list (multi information display - Type 1) Screen Cause Solution (Reference)  The Ultrasonic misacceleration Mitigation Refer to “Ultrasonic misacceleration Mitiga- System (UMS) is activated. tion System (UMS)” on page 6-109.  When the Ultrasonic misacceleration Miti- Refer to “When the Ultrasonic misacceleration gation System (UMS) is ON, if the drive Mitigation System is not available”...
Page 141 Indicator lamp, warning lamp, and information screen display list (multi information display - Type 1) Screen Cause Solution (Reference)  When the Ultrasonic misacceleration Miti- Refer to “When the Ultrasonic misacceleration gation System (UMS) is ON, if the rear dif- Mitigation System is not available”...
Page 142  The Blind Spot Warning (BSW) does not  Immediately have your vehicle inspected at operate normally because there are some an authorised MITSUBISHI MOTORS malfunctions in the sensor or the system. dealer. Refer to “When there is a malfunction in the system or the sensor”...
Page 143 Indicator lamp, warning lamp, and information screen display list (multi information display - Type 1) Screen Cause Solution (Reference)  More than specified limit water has accu-  Refer to “Removal of water from the fuel mulated in the fuel filter. filter (diesel-powered vehicles)”...
Page 144 Indicator lamp, warning lamp, and information screen display list (multi information display - Type 1) Screen System operation status Reference  When the drive mode is shifted by operat- Refer to “Super select 4WD Ⅱ ”on page 6-50. ing the drive mode-selector. ...
Page 145 Indicator lamp, warning lamp, and information screen display list (multi information display - Type 1) Screen System operation status Reference  When the Forward Collision Mitigation Refer to “Forward Collision Mitigation Sys- System (FCM) is activated or the timing of tem (FCM) and Ultrasonic misacceleration an alarm is changed.
Page 146 Indicator lamp, warning lamp, and information screen display list (multi information display - Type 1) The setting for rest interval can be changed. Screen Solution Stop the vehicle in a safe place, turn off the engine, and take a rest. Use this display as rough guide for taking rests during a long drive.
Page 147: Indicator And Warning Lamps (Multi Information Display - Type 2)
Indicator and warning lamps (multi information display - Type 2) Indicator and warning lamps (multi information display - Type 2) E00501504022 15- Fuel filter indicator lamp (diesel pow- 9- Rear fog lamp indicator lamp* → 1- Front fog lamp indicator lamp* ...
Page 148: Indicator Lamps
Indicator lamps When the hazard warning lamp switch is 23- Seat belt warning lamp Position lamp indicator lamp  P.4-16 pressed, all turn-signal lamps will flash on E00508901314 and off continuously. 24- Anti-lock brake system (ABS) warning This indicator lamp illumi- lamp ...
Page 149: Warning Lamps
Warning lamps CAUTION Fuel filter indicator lamp (die- Warning lamps sel- powered vehicles equipped  If the diesel preheat indicator lamp comes on E00502400147 after the engine is started, the engine speed with the multi information dis- may not rise above the idling speed because Brake warning lamp (red) play - type 2) of fuel freezing.
Page 150 MOTORS dealer should be contacted. switch. (Refer to “Electric parking brake” MITSUBISHI MOTORS dealer. If you inev- on page 6-8) itably have to park, park the vehicle on level • The brake warning lamp does not illumi-...
Page 151  If it illuminates while the engine is running, MITSUBISHI MOTORS dealer as soon as engine seizure may occur. there is a problem in the charging system.
Page 152: Information Screen Display (Vehicle Equipped With The Multi Information Display - Type 1)
Information screen display (Vehicle equipped with the multi information display - Type 1) CAUTION Engine oil level warning lamp Washer fluid level warning (Vehicle equipped with the lamp (Vehicle equipped with  Before moving your vehicle, check that the warning lamp is OFF. multi information display - the multi information display - Type 2)
Page 153 Information screen display (Vehicle equipped with the multi information display - Type 1) lamp in the instrument cluster also illumi- CAUTION CAUTION nates when the parking brake is applied.  If this warning stays illuminated and does • Should the brakes fail, use engine braking If this warning is displayed, release the park- not go out while driving, there is a danger of to reduce your speed and observe the fol-...
Page 154: Combination Headlamps And Dipper Switch
Combination headlamps and dipper switch CAUTION Engine oil level warning Combination headlamps display (diesel- powered vehi-  If the warning is displayed while the engine and dipper switch is running, immediately park your vehicle in cles) E00506004123 a safe place and we recommend you to have it checked.
Page 155 Combination headlamps and dipper switch Type 1 Type 2 NOTE  The sensitivity of the automatic on/off con- Rotate the switch to turn on the lamps. Rotate the switch to turn on the lamps. trol can be adjusted. For further information, contact authorised MITSUBISHI...
Page 156 For further information, please contact your in the “OFF” or “AUTO” position and the tail [Except for vehicles equipped with the authorised MITSUBISHI MOTORS dealer. lamps are off. keyless operation system] The ignition switch is turned to the Dipper (High/Low beam “LOCK”...
Page 157  If you turn the lamps off with the headlamps For further information, please contact your set to high-beam, the headlamps are auto- authorised MITSUBISHI MOTORS dealer. matically returned to their low-beam setting when the lamp switch is next turned to the “...
Page 158: Headlamp Levelling
• The time that the headlamps remain on can be changed. • The coming home light function can be : 1 person deactivated. :Full luggage loading For further information, please contact your authorised MITSUBISHI MOTORS dealer. Switch position 0- Instruments and controls 5-61...
Page 159: Turn-Signal Lever
Turn-signal lever minated with the ignition switch in the “ON” Driver only / Driver + 1 front passenger Vehicle condition Switch position position or the operation mode in ON, the Switch position 1- beam position of the headlamps is automati- 5 passengers (including driver) “4”...
Page 160: Hazard Warning Flasher Switch
- type 2] For further information, please contact your ment cluster will flash 3 times. authorised MITSUBISHI MOTORS dealer. NOTE Hazard warning flasher  If the lamp flashes unusually quickly, the Fog lamp switch...
Page 161: Wiper And Washer Switch
Wiper and washer switch [Vehicle without front fog lamps] NOTE Turn the knob once in the “ON” direction to  The rear fog lamp is automatically turned off turn on the rear fog lamp. To turn the rear fog when the headlamps or front fog lamps (if so lamp off, turn the knob once in the “OFF”...
Page 162 2- Slow NOTE  The speed-sensitive-operation function of the windscreen wipers can be deactivated. For further information, please contact your authorised MITSUBISHI MOTORS dealer. MIST- Misting function MIST- Misting function Misting function The wipers will operate once. The wipers will operate once.
Page 163 For further information, please contact your the operation mode is in ON. to deactivate the rain sensor. authorised MITSUBISHI MOTORS dealer. If the lever is put in the “AUTO” position, the • When cleaning the outside surface of the • When the wipers operate at a constant inter- windscreen, if you touch on top of the rain val despite changes in the extent of rain.
Page 164 (C) is turned in the “+” direction when the can be changed to intermittent operation ignition switch is in the “ON” position or the (except vehicle-speed sensitive). operation mode is in ON. For further information, please contact your authorised MITSUBISHI MOTORS dealer. Instruments and controls 5-67...
Page 165 For further information, please contact your using the washer. onto the rear window when the authorised MITSUBISHI MOTORS dealer. knob is turned fully in either direc-  If the knob is in the “OFF” position, turn the tion.
Page 166: Rear Window Demister Switch
Rear window demister switch During cold weather, add a recommended Headlamp washer switch Precautions to observe when washer solution that will not freeze in the using wipers and washers E00510101603 washer reservoir. Failure to do so could result in loss of washer function and frost E00507601529 The headlamp washer can be operated with ...
Page 167: Horn Switch
Horn switch Customizing the automatic rear NOTE Type 2 window demister (Vehicles  The factory setting is “Disable automatic rear window demister”. equipped with the rear window demister switch - Type 2) Horn switch Function can be changed as desired, as stated E00508001777 below.
Page 168 Starting and driving Economical driving ................6-2 Hill Descent Control (HDC)*............6-77 Driving, alcohol and drugs ..............6-3 Brake assist system*...............6-79 Safe driving techniques ..............6-3 Anti-lock brake system (ABS) ............6-80 Running-in recommendations ............6-4 Power steering system ..............6-82 Parking brake ...................6-6 Active Stability & Traction Control (ASTC)* .......6-82 Parking ...................6-12 Cruise control* ................6-85 Steering wheel height and reach adjustment ........6-13...
Page 169: Economical Driving
Frequent starting and stopping increases the nomical operation, have the vehicle Serviced average fuel consumption. Use roads with by an authorised MITSUBISHI MOTORS Cargo loads smooth traffic flow whenever possible. When dealer at regular intervals in accordance with driving on congested roads, avoid use of a the service standards.
Page 170: Driving, Alcohol And Drugs
Driving, alcohol and drugs Cooler or air conditioning Safe driving techniques E00600300446 The use of the air conditioner will increase Driving safety and protection against injury the fuel consumption. cannot be fully ensured. However, we recom- mend that you pay extra attention to the fol- lowing: Driving, alcohol and drugs E00600200070...
Page 171: Running-In Recommendations
Running-in recommendations not only because rearward vision will be jected into the passenger compartment under obstructed, but also the luggage may be pro- hard braking. Running-in recommendations E00600403956 During the running-in period for the first 1,000 miles, it is advisable to drive your new vehicle using the following precautions as a guideline to aid long life as well as future economy and performance.
Page 173: Parking Brake
Parking brake 4WD models Speed limit Diesel-powered vehicles Shift point Petrol-powered vehicles 4D56 4N15 2H, 4H, 4HLc 4LLc 2H, 4H, 4HLc 4LLc 2H, 4H, 4HLc 4LLc 9 mph 3 mph 1st gear 19 mph 6 mph 2nd gear 31 mph 12 mph 3rd gear 40 mph...
Page 174 Parking brake To apply NOTE CAUTION  Apply sufficient force to the parking brake  Before driving, be sure that the parking E00641900047 lever to hold the vehicle stationary after the brake is fully released and brake warning foot brake is released. lamp is off.
Page 175 Parking brake To apply NOTE CAUTION  To prevent the parking brake from being  When the need arises to apply the parking E00642200047 released unintentionally, the lever must be brake as the emergency brake for a failure of pulled up slightly before it can be pushed the foot brake etc.
Page 176  When the operation mode is other than ON, lamp will blink. If the lamps remain blink- the parking brake cannot be released. ing, immediately park your vehicle in a safe place contact authorised MITSUBISHI MOTORS dealer. Starting and driving...
Page 177  Do not drive with the Electric parking brake safe place, and contact your authorised applied. The brake parts may be worn early MITSUBISHI MOTORS dealer. If you inev- Warning display and the brake may be disabled by overheat. itably have to park, park the vehicle on level ...
Page 178 Parking brake WARNING  When releasing the Electric parking brake manually, be sure to move the selector lever to the “P” (PARK) position. Other- wise, the vehicle may begin to move, which may lead to an unexpected accident. 3. Stop the engine if it is running. 4.
Page 179: Parking
Parking 9. After turning the tool approximately 50 to On vehicles equipped with M/T, apply the Parking with the engine run- 100 times while pushing it, it becomes parking brake and place the gearshift lever ning hard to turn it. into the “R”...
Page 180: Steering Wheel Height And Reach Adjustment
Steering wheel height and reach adjustment Always try to park your vehicle in a well lit Inside rear-view mirror To adjust the vertical mirror area. position E00600802038 Adjust the rear-view mirror only after making Steering wheel height and any seat adjustments so you have a clear view It is possible to move the mirror up and down reach adjustment to the rear of the vehicle.
Page 181: Outside Rear-View Mirrors
Outside rear-view mirrors When the ignition switch is turned to the “ON” position or the operation mode is put in ON, the reflection factor of the mirror is auto- matically changed. NOTE  Do not hang items on, or spray glass cleaner on the sensor (1), as reduced sensitivity could result.
Page 182 Outside rear-view mirrors 3- Right Electric remote-controlled outside 4- Left rear-view mirrors 3. Return the lever (A) back to the middle position (•). The outside rear-view mirrors can be oper- ated when the ignition switch is in the “ON” Retracting and extending the or “ACC”...
Page 183 Outside rear-view mirrors Refer to “Keyless entry system” on page 3-4. NOTE Refer to “Keyless operation system: To oper-  If you move a mirror by hand or it moves ate using the keyless operation function” on after hitting a person or object, you may not pages 3-9.
Page 184: Ignition Switch
Ignition switch* NOTE LOCK NOTE • Deactivate the automatic extension func-  Your vehicle is equipped with an electronic tion. immobilizer. The engine is stopped and the steering wheel To start the engine, the ID code which the locked. The key can only be inserted and The outside rear-view mirrors can be folded transponder inside the key sends must match removed in this position.
Page 185: Engine Switch
 Do not turn the key to the “START” position flashing orange. Immediately contact your while the engine is running. Doing so could authorised MITSUBISHI MOTORS dealer. damage the starter motor.  If the engine switch operation is not smooth and feels like it is sticking, do not operate the switch.
Page 186 Engine switch* Operation mode of the engine NOTE CAUTION switch and its function  Your vehicle is equipped with an electronic  When the engine is not running, put the oper- immobilizer. ation mode in OFF. Leaving the operation To start the engine, the ID code which the mode in ON or ACC for a long time when transponder inside the key sends must match the engine is not running may cause the bat-...
Page 187: Steering Wheel Lock
Turn the key to the “ACC” position while Operation mode ON reminder MITSUBISHI MOTORS dealer. moving the steering wheel slightly right and system left. E00632301114 If the driver’s door is opened with the engine stopped and the operation mode in any mode...
Page 188 Steering wheel lock NOTE CAUTION • Close all the doors and the tailgate.  If the engine is stopped while driving, do not open a door or press the LOCK switch on the • Open one of the doors or the tailgate when key until the vehicle stops in a safe place.
Page 189 And then press the engine ised MITSUBISHI MOTORS dealer. switch, If the warning lamp illuminates Warning lamp (mono-color liquid crystal Warning lamp (mono-color liquid crystal...
Page 190: Starting And Stopping The Engine
Starting and stopping the engine Starting and stopping the CAUTION WARNING engine  Do not run the engine at high speeds or drive  Never run the engine in a closed or poorly the vehicle at high speeds until the engine ventilated area any longer than is needed E00620601530 has had a chance to warm up.
Page 191 If the engine still will start, contact your authorised MITSUBISHI MOTORS dealer. When the engine is hard to start 5. Press the engine switch. 6. Make certain that all warning lamps are Using the MIVEC engine functioning properly.
Page 192 Starting and stopping the engine with driving conditions for maximum engine 6. Turn the ignition key to the “START” Vehicles Vehicles Vehicles performance. position without depressing the accelera- with 6M/T with 5M/T with A/T tor pedal, and release it when the engine starts.
Page 193 Starting and stopping the engine On vehicles equipped with A/T, make NOTE NOTE sure the selector lever is in the  If the engine is cold, the diesel preheat indi-  When starting the engine, the selector lever “P”(PARK) position. cator lamp is on for a longer time.
Page 194 Starting and stopping the engine 2. Fully engage the parking brake while Remove the keyless operation key from the For vehicles equipped with the keyless depressing the brake pedal. key slot after starting the engine or changing operation system 3. On vehicles with M/T, press the engine the operation mode.
Page 195: Diesel Particulate Filter (Dpf)
Diesel particulate filter (DPF)* ation key in the key slot, the warning lamp NOTE CAUTION will blink and the outer buzzer sounds for  Remove the object or additional key from the  Do not use any type of fuel or engine oil that approximately 3 seconds and the inner buzzer keyless operation key before inserting the is not specified for your vehicle.
Page 196: Turbocharger Operation
Turbocharger operation* Warning display (color liquid crystal display) nate. Have the system inspected by an CAUTION authorised MITSUBISHI MOTORS dealer.  You do not have to continuously drive exactly as indicated above. Always strive to CAUTION drive safely in accordance with road condi- tions.
Page 197: Manual Transmission
Manual transmission* fied intervals, the bearings may seize or emit CAUTION Moving the gearshift lever to abnormal noise. the “R” (Reverse) position  Do not put the gearshift lever into the reverse position while the vehicle is moving for- E00615401266 ward.
Page 198 Manual transmission* CAUTION  Do not depress the gearshift lever when moving it to any position other than the “R” (Reverse) position. If you always depress the gearshift lever when moving it, you could unintentionally move the gearshift lever to the “R”...
Page 199: 5-Speed Automatic Transmission With Sports Mode
5-Speed automatic transmission with sports mode* 4WD models - Not UK Spec Speed limit Shift point 4D56 4N15 2H, 4H, 4HLc 4LLc 2H, 4H, 4HLc 4LLc 1st gear 35 km/h 15 km/h 35 km/h 10 km/h 2nd gear 65 km/h 35 km/h 65 km/h 25 km/h...
Page 200  Always depress the brake pedal when have your vehicle checked by an authorised shifting the selector lever into a gear from MITSUBISHI MOTORS dealer. the “P” (PARK) or “N” (NEUTRAL) posi- If you need to move the vehicle, shift the tion.
Page 201 5-Speed automatic transmission with sports mode* 5. Insert a straight blade (or minus) screw- Vehicles equipped with the color liquid crystal driver in the shift-lock release hole (B). display Shift the selector lever to the “N” (NEU- TRAL) position while pressing the straight blade (or minus) screwdriver down.
Page 202 5-Speed automatic transmission with sports mode* “N” NEUTRAL CAUTION + (SHIFT UP)  To prevent transmission damage, never shift The transmission shifts up by one gear with into the “D” (DRIVE) position from the “R” At this position the transmission is disen- each operation.
Page 203 5-Speed automatic transmission with sports mode* Sports mode indicator display NOTE When a malfunction occurs in the A/T  To maintain good running performance, the E00612301613 transmission may refuse to perform an In sports mode, the currently selected posi- E00615101377 upshift when the selector lever is moved to tion is indicated by the indicator (A) shown the “+ (SHIFT UP)”...
Page 204 5-Speed automatic transmission with sports mode* NOTE  “A” indicator does blink only the condition that the A/T positional switch is broken. It does not indicate in normal driving condi- NOTE tion.  The buzzer may sounds at the time of warning display appears.
Page 205 5-Speed automatic transmission with sports mode* Passing acceleration CAUTION CAUTION • Stop your vehicle in a safe place, put the  Depress the brake pedal with the right foot at E00604501342 selector lever in the “P” (PARK) position, all times. To gain extra acceleration in “D”...
Page 206: 8-Speed Automatic Transmission With Sports Mode
8-Speed automatic transmission with sports mode* your vehicle checked at an authorised Parking 8-Speed automatic transmis- MITSUBISHI MOTORS dealer. sion with sports mode E00604701302 To park the vehicle, first bring it to a com- 1. If your vehicle has difficulty moving...
Page 207 8-Speed automatic transmission with sports mode* WARNING  Always depress the brake pedal when shifting the selector lever into a gear from the “P” (PARK) or “N” (NEUTRAL) posi- tion. Never put your foot on the accelerator pedal while shifting the selector lever from the “P”...
Page 208  If you would like to move your vehicle when E00603801885 MITSUBISHI MOTORS dealer. the selector lever cannot be moved from the If you need to move the vehicle, shift the “P” (PARK) position and the Electric park- “P”...
Page 209 8-Speed automatic transmission with sports mode* WARNING NOTE NOTE  Never move the selector lever to the “N”  While driving on uphills or downhills, when  You can shift into sports mode with shift (NEUTRAL) position while driving. A the accelerator pedal is suddenly released or paddles when the selector lever is in the serious accident could occur since you...
Page 210 8-Speed automatic transmission with sports mode* NOTE - (SHIFT DOWN)  To maintain good running performance, the The transmission shifts down by one gear transmission may refuse to perform an with each operation. upshift when the selector lever is moved to the “+ (SHIFT UP)”...
Page 211 8-Speed automatic transmission with sports mode* NOTE CAUTION CAUTION  The “A” indicator on the selector lever posi-  To prevent sudden acceleration, never race After a while, confirm that the warning tion display will only blink if there is a prob- the engine when shifting from the “P”...
Page 212 E00604700187 force on the pedal changes. When the accel- your vehicle checked at an authorised To park the vehicle, first bring it to a com- erator pedal is fully depressed, the transmis- MITSUBISHI MOTORS dealer. sion shifts down automatically. plete stop, fully engage the parking brake, transmission can control to shift down for and then move the selector lever to the “P”...
Page 213 Super select 4WD* Transfer shift Indica- Driving con- Super select 4WD Transfer shift lever position lever position tor lamp ditions and 2WD/4WD operation indi- E00605701295 When driv- cator lamp Shifting to rear-wheel drive or 4-wheel drive ing up or can be made by operating the transfer shift E00605801397 Low range down steep...
Page 214 Super select 4WD* The transfer shift lever should be positioned To shift CAUTION Procedure in accordance with the following operating from  Do not drive your vehicle in the “4HLc” or conditions: “4LLc” on dry paved roads and highways. 4HLc 4LLc Stop the vehicle, depress Doing so may result in excessive tyre wear, the clutch pedal to the...
Page 215 Super select 4WD* “2H”  “4H” NOTE 2WD/4WD operation indicator lamp and low-range indicator  When the transfer shift lever is shifted from “4H” to “4HLc” while the vehicle is stopped, lamp Transfer shift lever Indicator lamp the 2WD/4WD operation indicator lamp position blinks while the selection is in process.
Page 216 Super select 4WD* “4H”  “4HLc” “4HLc”  “4LLc” NOTE • Keep the steering wheel in the straight ahead position while making range selec- Transfer shift lever Transfer shift lever Indicator lamp Indicator lamp tions. If you attempt to drive forward with position position the steering wheel turned, gear rattling may...
Page 217: Super Select 4Wd Ii
Super select 4WD II* Refer to “Drive mode indicator lamp/display Vehicles with 8A/T NOTE and 2WD/4WD operation indicator lamp/dis-  When you move the transfer shift lever from play” on page 6-54, 6-56. “4H” to “4HLc”, there may be a slight delay before the centre differential lock lamp illu- Except for vehicles with 8A/T minates.
Page 218 Super select 4WD II* Indicator lamp/display Drive mode-selector position Driving conditions Mono-color liquid Color liquid crystal crystal display display Full-time 4-wheel The basic position for Super select 4WD II. drive When driving on dry paved or slippery roads. Centre differential 4HLc lock engaged 4-wheel When driving on rough, sand or snow covered roads.
Page 219 Super select 4WD II* : Turn the drive mode-selector while Drive mode-selector operation holding it down E00650900030 The drive mode-selector should be positioned The drive mode is shown on the drive mode- in accordance with the following operating selector knob. conditions: : Turn the drive mode-selector Procedure...
Page 220 Super select 4WD II* Procedure To shift from Vehicles with M/T Vehicles with A/T 4HLc 4LLc Stop the vehicle, depress the clutch pedal to the floor and Stop the vehicle, shift the selector lever to the “N” (NEU- operate the drive mode-selector. TRAL) position, depress and hold the brake pedal, and Keep depressing the clutch pedal while the 2WD/4WD operate the drive mode-selector.
Page 221 Super select 4WD II* display” on page 6-56.  “2H”  “4H”  “4H”  “4HLc” 2WD/4WD operation indicator Drive mode-selec- Drive mode-selec- Indicator lamp Indicator lamp lamp and low-range indicator tor position tor position lamp E00651100026 Drive mode switch- Drive mode switch- ing in progress ing in progress...
Page 222 Super select 4WD II*  “4HLc”  “4LLc” : Remain off NOTE  On vehicles with A/T, when parking, apply NOTE the parking brake before stopping the engine Drive mode- and make sure that the front and the rear selector Indicator lamp ...
Page 223 Super select 4WD II* Drive mode indicator display and NOTE CAUTION 2WD/4WD operation indicator  On vehicles with the active stability & trac-  If a problem is detected in the transfer sys- tion control (ASTC), the active stability con- tem, a safety device will activate.
Page 224 Super select 4WD II*  “2H”  “4H”  “4H”  “4HLc”  “4HLc”  “4LLc” Drive mode-selec- Drive mode-selec- Drive mode- Indicator display Indicator display tor position tor position selector Indicator display position 4HLc Drive mode switch- Drive mode switch- ing in progress ing in progress Drive mode...
Page 225 Super select 4WD II* NOTE NOTE NOTE  When the drive mode-selector is set between  When parking, apply the parking brake  If the selector lever is shifted from the “N” “2H”, “4H” and “4HLc”, the front wheel before stopping the engine and make sure (NEUTRAL) position to the other position or and/or centre differential lock displays blink that the front and the rear wheel displays and...
Page 226 A/T. If this happens, please contact your nearest authorised MITSUBISHI MOTORS dealer for inspec- tion. When this warning display appears, shifting only between a “2H”  “4H”  “4HLc” selection can be made. In addition, when the drive mode-selector is in “4LLc”, the trans-...
Page 227: Off Road Mode
Off Road mode* Off Road mode E00642500040 The Off Road mode is the function that enhances driving smoothly on the off-road by selecting the most suitable engine, transmission, and brake control according to the road surface conditions when the drive mode position of Super select 4WD II is in “4HLc” or “4LLc”. Also refer to “Super select 4WD II”...
Page 228: Rear Differential Lock
Rear differential lock* 2. Set the drive mode-selector from “2H” or In addition, the selected mode is displayed as NOTE “4H” to “4HLc” or “4LLc”. At this time, an interrupt display on the information screen  The Off Road mode is not activated when the the OFF Road mode is switched to of the multi information display (B) by drive mode is in “2H”...
Page 229 Rear differential lock* NOTE  Vehicles equipped with the color liquid crys- tal display, if the rear differential lock switch is turned on during driving, the warning dis- play will appear and the rear differential lock will remain deactivated. CAUTION The rear differential lock indi- Operating the rear differential ...
Page 230 Rear differential lock* Indicator lamp : Blink NOTE : Illuminate (steady)  The status of the rear differential lock (resulting from depression of the rear differ- : Remain off ential lock switch) is shown by blinking or steady illumination of the rear differential [Vehicles equipped with the color liquid lock indicator lamp/display.
Page 231 Rear differential lock* : Blink (Drive mode indicator dis- NOTE CAUTION play also blinks)  If the indicator lamp/display continues blink-  If a problem is detected in the rear differen- ing after the switch has been pressed to acti- : Illuminate (steady) tial lock system, a safety device will activate.
Page 232 Rear differential lock* When driving on rocky roads Examples of effective use of the rear differential lock When the vehicle is unable to move because E00606401156 one of the wheels is suspended in the air. CAUTION  Use the rear differential lock only as an emergency measure when the vehicle is stuck and cannot be freed with the drive mode-selector in “4LLc”...
Page 233: 4-Wheel Drive Operation
4-wheel drive operation* WARNING WARNING  If the rear differential lock is used by mis-  If the rear differential lock is used by mis- take when turning a curve or making a take except when making an emergency right or left turn at a crossing or the like: escape on snow or frozen road: It becomes The vehicle is unable to make a turn and difficult to make a steady turn.
Page 234 4-wheel drive operation* However, note that the braking distance is not shorter than that of a rear-wheel drive vehicle. When using 4-wheel drive on rough roads (snow, mud, sand, etc.), it is important to operate the vehicle correctly. WARNING  Control the accelerator pedal, brake pedal, steering wheel, etc. according to the landform and nature of the soil. The driver should accurately grasp the surrounding circumstances and drive carefully according to the respective circumstances.
Page 235 4-wheel drive operation* Even a vehicle without the equipment for Off Road mode and rear differential lock (if so equipped) run each road condition. The vehicle with each equipment set the recommended mode of the list shown below in each road condition, it may help you drive smoothly. Road conditions Driving mode Dry paved road...
Page 236 4-wheel drive operation* Driving on dry paved road and Driving on packed snow roads Driving on unpaved roads highway E00646500048 E00646600049 E00646400047 Set the transfer shift lever or the drive mode- Check the road surface conditions and set the selector to “4H” position, in accordance with transfer shift lever or the drive mode-selector Set the transfer shift lever or the drive mode- the road conditions, and then gradually...
Page 237 4-wheel drive operation* to get stuck. This may help you drive NOTE Driving on sandy roads smoothly.  If the vehicle becomes stuck in deep snow or E00646700040 muddy roads, it can often be moved a rock- WARNING ing motion. Move the selector lever rhythmi- ...
Page 238 Avoid changing gears or depressing the clutch while descend- ing the grade.  MITSUBISHI MOTORS is not responsible to the operator for any damage or injury caused or liability incurred by the improper and negligent operation of a vehicle. All...
Page 239 4-wheel drive operation* Climbing steep grades Turning sharp corners Crossing a stream E00647000040 E00647100041 E00647200042 Set the transfer shift lever or the drive mode- When turning a sharp corner in “4HLc” or 4-wheel drive vehicles are not necessarily selector to “4LLc” position to maximize the “4LLc”...
Page 240: Inspection And Maintenance Following Rough Road Operation
If the brakes still do not deep. function properly, contact an authorised E00606802030 Do not change gears while crossing the MITSUBISHI MOTORS dealer as soon stream. as possible to have the brakes checked. Frequent crossing of streams can adversely Tyres and wheels ...
Page 241 Only when you cannot receive a towing ser- CAUTION larly. vice from a MITSUBISHI MOTORS dealer  Be sure to shift the transfer shift lever or set or commercial tow truck service, tow your the drive mode-selector to “2H” position and...
Page 242: Limited-Slip Differential
Have the vehicle serviced by an will not work effectively. when the vehicle is cornering. The difference authorised MITSUBISHI MOTORS dealer at  If the power assist is lost or if either brake between the limited-slip differential and a...
Page 243: Hill Start Assist
Hill start assist*  The disc brakes are provided with a warn- cially when the brakes are wet, to confirm CAUTION they work normally. ing device which emits a shrieking metal-  The hill start assist is not designed to keep A film of water can be formed on the brake lic sound while braking if the brake pads the vehicle stopped in place on uphill slopes...
Page 244: Hill Descent Control (Hdc)
Hill Descent Control (HDC)* 3. Release the brake pedal and the hill start NOTE CAUTION assist will maintain the braking force • The vehicle is completely stationary, with  If the warning is displayed, the hill start applied while stopping for approximately the brake pedal depressed.
Page 245  It is impossible to set the Hill Descent Con- come on, have the vehicle inspected at an cator lamp comes on. trol to ON (stand by) in the following condi- authorised MITSUBISHI MOTORS dealer. When the Hill Descent Control indicator tions. (Refer to “ASTC warning lamp/display” on lamp comes on, the Hill Descent Control •...
Page 246: Brake Assist System
Brake assist system* lamps and the high mounted stop lamp are 2. Make sure that the Hill Descent Control CAUTION illuminated. It is possible to change the con- indicator lamp is off.  The brake assist system is not a device trolled vehicle speed by operating the acceler- designed to exercise braking force greater ator pedal or the brake pedal.
Page 247: Anti-Lock Brake System (Abs)
(The standard brake system is func-  Do not install any aftermarket limited slip tioning normally.) If this happens, please differential (LSD) on your vehicle. The ABS contact your nearest authorised may stop functioning properly. MITSUBISHI MOTORS dealer for inspec- tion. 6-80 Starting and driving...
Page 248 ASTC indicator lamp, ASTC OFF indicator Stop the vehicle in a safe place and contact an vehicle is driven, have the vehicle checked by lamp and ABS warning lamp are illuminated authorised MITSUBISHI MOTORS dealer. while these functions are suspended. authorised MITSUBISHI MOTORS It does not indicate a problem.
Page 249: Power Steering System
Power steering system ful not to damage the wheel speed sensors WARNING CAUTION (A) and cables located at each wheel.  Do not stop the engine while the vehicle is  Do not over-rely on the ASTC. Even the moving. Stopping the engine would make ASTC cannot prevent the natural laws of Front Rear...
Page 250 Active Stability & Traction Control (ASTC)* NOTE NOTE  When the ASTC is activated, you may feel a  Vehicles with super select 4WD II, the active vibration in the vehicle body or hear a whin- stability control function does not operate ing sound from the engine compartment.
Page 251 ON, please contact your nearest authorised warning to the driver. If the driver continues  Even if the active stability control function is MITSUBISHI MOTORS dealer for inspec- driving even after the warning buzzer sounds turned off, it may activate depending on the tion.
Page 252: Cruise Control
Cruise control* NOTE NOTE CAUTION  The ASTC function indicator display illumi-  The system may be malfunctioning.  The indicator lamp may turn on when nates only when the 2WD/4WD operation Park your vehicle in a safe place and stop the you start the engine.
Page 253 Cruise control* CAUTION Cruise control switches NOTE  When you do not wish to drive at a set speed,  When operating the cruise control switches, turn off the cruise control for safety. press the cruise control switches correctly. The set speed driving may be deactivated ...
Page 254 Cruise control* Indicator display Accelerator pedal To increase the set speed E00609401841 While driving at the set speed, use the accel- There are 2 ways to increase the set speed. erator pedal to reach your desired speed and then push down the SET - switch (B) and 2.
Page 255 Cruise control* When you reach your desired speed, release the switch. Your new cruising speed is now set. To temporarily increase or To temporarily decrease the speed decrease the speed Depress the brake pedal to decrease the To slow down your speed in small amounts, E00609601351 speed.
Page 256 ON/OFF your vehicle inspected by an authorised because of a hill, etc. switch is pressed. MITSUBISHI MOTORS dealer.  When your speed slows to approximately  The ignition switch is turned OFF or the 25 mph or less. operation mode is put in OFF.
Page 257: Adaptive Cruise Control System (Acc)
Adaptive Cruise Control System (ACC)*  Indicator lamp go off. WARNING CAUTION  A driver is responsible for driving safely.  In the following situations, the system may Adaptive Cruise Control Even if the ACC is in use, always grasp become transiently unable to detect a vehicle the surrounding circumstances and pro- in front or triggers its control and alarm...
Page 258 Adaptive Cruise Control System (ACC)* CAUTION CAUTION NOTE  Never use the ACC in any of the following • Avoid application of strong shock loads to  When depressing the brake pedal while auto- situations. Failure to follow this instruction the sensor and never tamper with or remove matic brake is applied, the brake pedal is felt could lead to an accident.
Page 259 Adaptive Cruise Control System (ACC)* resume the set speed and continues running at WARNING that speed. • When driving on a curve. NOTE  If the vehicle in front turns off or changes lane and another stationary vehicle is  If you do not depress the brake pedal within located in front of that vehicle, the ACC 1.5 seconds after an automatic stop, you are WARNING...
Page 260 Adaptive Cruise Control System (ACC)* CAUTION CAUTION  The ACC may not be able to maintain the set • When the emblem and the sensor become speed or the distance to a vehicle in front and dirty or adhering snow and ice*. may not alert the driver, if the system cannot •...
Page 261 Adaptive Cruise Control System (ACC)* State Cruise control switch NOTE Display Stand by Active  Operate the individual switches correctly and E00634801067 one after another. The ACC may be turned off or its control Vehicle in function may be cancelled if two or more front switches are pressed concurrently.
Page 262 Adaptive Cruise Control System (ACC)* The display on the information screen of the To activate ACC control How to use ACC multi information display will switch to show E00635001242 information on the ACC. With the ACC turned on (in the ‘standby When the ACC is activated, it is placed in the state’), push down the “SET -”...
Page 263 Adaptive Cruise Control System (ACC)* The set speed is indicated on the information NOTE NOTE screen of the multi information display. • When the vehicle speed is lower than • The Hill Descent Control is operating (if so The ACC can be selected between approxi- approximately 6 mph or 93 mph or equipped).
Page 264 Adaptive Cruise Control System (ACC)* NOTE By using the “RES +” switch: By using the accelerator pedal:  The ACC control at the original set speed The set speed increases by 1 mph every time When the accelerator pedal is depressed resumes as soon as you release the accelera- you push up the “RES +”...
Page 265 Adaptive Cruise Control System (ACC)* To temporarily accelerate the vehi- NOTE By using the brake pedal:  There is some time lag between the setting to If you depress the brake pedal while the ACC a new speed and actually decelerating to that control is working, the control is cancelled, Simply depress the accelerator pedal to tem- speed.
Page 266 Adaptive Cruise Control System (ACC)* When the control is cancelled, the system is When the system shifts into the ‘standby NOTE placed in the ‘standby state’. You can make state’ as a result of cancellation of the ACC  In certain conditions, the braking control and the system restart the control by using the control, the “SET”...
Page 267 Adaptive Cruise Control System (ACC)*  The Hill Descent Control is operating (if The ACC control is automatically cancelled and the ACC is placed in the ‘standby’ state so equipped). in any of the situations listed below; you are  The vehicle speed reaches approximately 99 mph or higher.
Page 268 “OFF”, the system is setting MITSUBISHI MOTORS dealer. set to the ‘OFF state’ when the operation E00638400051 mode is set to “ON” next time. Every time you press the following distance setting switch, the setting changes sequen- tially through three options “Long”, “Middle”...
Page 269: Forward Collision Mitigation System (Fcm)
Forward Collision Mitigation System (FCM)*  Cruise control (automatic speed control When the risk of collision increases more, the NOTE system) P.6-85 system causes the brakes to work moderately  The following distance varies as a function to encourage you to apply brakes. If the sys- of the speed;...
Page 270 Forward Collision Mitigation System (FCM)* WARNING Forward collision warning FCM brake prefill function function  A driver is responsible for driving safely. E00635200016 The FCM is the system to mitigate colli- If the system judges that there is a risk of E00635401103 sion-caused damages or to avoid collisions If the system judges that there is a risk of...
Page 271 Forward Collision Mitigation System (FCM)* CAUTION FCM braking function CAUTION  The brake assist function may not be trig-  When applying the brake during the auto- E00635501348 If the system judges that there is a high risk of gered when the brake pedal is operated in matic braking condition the pedal will feel certain ways.
Page 272 Forward Collision Mitigation System (FCM)* CAUTION CAUTION CAUTION • When the system is faulty (if the system • When the system is temporarily not availa- • When the sensor is not clean, “FCM self-detects any fault) the “FCM SERVICE ble, “FCM TEMPORARILY NOT AVAIL- RADAR BLOCKED”...
Page 273 Forward Collision Mitigation System (FCM)* CAUTION CAUTION CAUTION • When a motorcycle, bicycle, pedestrian, • When a road surface is surging, and there is *: When judging the state that detection per- animal, fallen objects, or anything other unevenness. formance deterioration by these situations than a vehicle is present in front of your automatically, “FCM RADAR BLOCKED”...
Page 274 • When passing through a gate with small • When making sports driving on a circuit. ised MITSUBISHI MOTORS dealer. head or side clearances. • When your vehicle is on a chassis •...
Page 275 Forward Collision Mitigation System (FCM)* tem (FCM) and Ultrasonic misacceleration CAUTION Mitigation System (UMS) OFF” indicator on  In the following conditions, even if the FCM the screen goes out. is ON, the FCM is automatically switched to OFF. In this case, the warning display may appear if you press the Forward Collision Mitigation System (FCM) and Ultrasonic misacceleration Mitigation System (UMS)
Page 276: Ultrasonic Misacceleration Mitigation System (Ums)
Ultrasonic misacceleration Mitigation System (UMS)* timing changes alternately between “FAR” When “NEAR” is selected When “FAR” is selected (earlier alarming), “MIDDLE” (normally alarming) and “NEAR” (later alarming). As you make selection, the selected alarm timing is displayed on the information screen of the multi information display.
Page 277 Ultrasonic misacceleration Mitigation System (UMS)* Situation Operation display Buzzer When an obstacle is detected in front of your vehicle with the Intermittent gearshift lever in a position other than “R”(Reverse) (vehicles beeping sound with M/T), or the selector lever in the “D” (DRIVE) position or in the sport mode (vehicles with A/T), if the accelerator pedal is depressed promptly and too strongly, the engine out- put is suppressed for up to approximately 5 seconds.
Page 278 Ultrasonic misacceleration Mitigation System (UMS)* WARNING WARNING CAUTION  Do not overly rely on the Ultrasonic mis- • Repeat to press the accelerator pedal  The Ultrasonic misacceleration Mitigation acceleration Mitigation System. It is never quickly to its full stroke more than System may not operate in the following a substitute for your safe and careful driv- 3 times.
Page 279 Ultrasonic misacceleration Mitigation System (UMS)* CAUTION CAUTION CAUTION • When the system judges driver’s steering or • When there are objects, steps or projections • Do not modify the suspension of your vehi- gear shifting actions as evasive actions to on the road surface.
Page 280 • Obstacles that have irregular surface. E00643800040 MITSUBISHI MOTORS dealer. • Obstacles that have the shape of the pole The Ultrasonic misacceleration Mitigation such as the road marker or the streetlight.
Page 281: Blind Spot Warning (Bsw)
Blind Spot Warning (BSW)* vehicle by informing the presence of another When there is a malfunction in the vehicle running diagonally behind your vehi- system or the sensor cle that may be in the blind spot of the outside E00644000052 rear-view mirrors.
Page 282 Blind Spot Warning (BSW)* Detection areas CAUTION CAUTION • When only a part of the vehicle is in the E00644400085 detection area of the sensor. The detection area is shown as illustrated. • When the surrounding vehicle or oncoming vehicle drives with blowing up the water, snow or sand on the road.
Page 283 Blind Spot Warning (BSW)*  When all the following conditions are sat- NOTE NOTE isfied, the Blind Spot Warning indicator  If the bumper has been exposed to an impact,  When the operation mode is set to OFF, the lamp in the meter comes on.
Page 284 When the sensor is temporarily • When there is a vehicle with an ultrasonic ised MITSUBISHI MOTORS dealer, and the sensor around your vehicle. not available valid ID set can be switched by the multi ...
Page 285 E00637200166 restarted, have the vehicle inspected by an authorised MITSUBISHI MOTORS dealer. In such situations, a malfunctioning of the system may be preventing the monitoring of When the operation mode is put in ON, the the tyre pressure.
Page 286 Tyre pressure monitoring system (TPMS)* Under-inflation also reduces fuel efficiency monitoring system (TPMS) malfunction tell- NOTE and tyre tread life, and may affect the vehi- tale after replacing one or more tyres or  In addition, the warning display is displayed cle’s handling and stopping ability.
Page 287  Snow or ice is stuck inside the fenders Driving with an under-inflated tyre MITSUBISHI MOTORS dealer to avoid the and/or on the wheels. adversely affects vehicle performance and risk of damaging the tyre inflation pressure  The tyre inflation pressure sensor’s bat- can result in an accident.
Page 288 Tyre pressure monitoring system (TPMS)* 1. Operate the multi-information display CAUTION switch to switch the information screen to  The use of non-genuine wheels will prevent the menu screen. the proper fit of the tyre inflation pressure Refer “Multi-information display sensors, resulting air leakage or damage of switch”...
Page 289: Reversing Sensor System
Reversing sensor system* Reversing sensor system detection NOTE CAUTION areas  When changing the tyre ID set, the reset  Make sure to check the surroundings with function of low tyre pressure warning thresh- your own eyes to ensure safety. Do not oper- old is automatically started.
Page 290 Have the vehicle inspected at an the “ON” position or the operation mode is cold weather). authorised MITSUBISHI MOTORS dealer. put in ON. When the reversing sensor system • The vehicle tilts significantly.  The sensors do not detect objects located in is operated, the reversing sensor system oper- •...
Page 291 Back sensor (vehicles with a towbar)  The volume of the warning buzzer can be adjusted. Vehicle to obstacle Warning dis- details, consult authorised distance play/sound cycle MITSUBISHI MOTORS dealer. Approximately 125 Intermittent to 100 cm 1- Corner sensor (left) 6-124 Starting and driving...
Page 292: Sensor System
Sensor system* Have the vehicle inspected at an authorised Changing the detection areas NOTE MITSUBISHI MOTORS dealer. • Setting when towbar is not equipped E00615801286 When the gearshift lever or selector lever is The detection areas can be changed as fol- moved to the “R”...
Page 293 Sensor system* CAUTION  The sensor system assists you in determining the approximate distance between the vehi- cle and any objects. It has limitations in terms of detectable areas and objects, and may not properly detect some objects. There- fore, do not place excessive confidence in the sensor system, and operate the vehicle as carefully as you would a vehicle without this system.
Page 294 Sensor system* NOTE CAUTION NOTE  If the bumper has been exposed to an impact, • The system receives ultrasonic noise from  The buzzer may sound lower than the normal the sensors may fail and prevent the system other sources (the horns of other vehicles, warning sound when the sensor system is from functioning properly.
Page 295  The volume of the warning buzzer can be mately 40 cm adjusted. details, consult authorised Back sensor (vehicles with a towbar) MITSUBISHI MOTORS dealer. Vehicle to obstacle Warning dis- distance play/sound cycle Changing the detection areas Approximately 125 Intermittent...
Page 296: Rear-View Camera
Please drive just as carefully the vehicle inspected at an authorised system operation differs according to the as you would if the vehicle did not have MITSUBISHI MOTORS dealer. detection area setting. the rear-view camera. • Setting when towbar is not equipped ...
Page 297 Rear-view camera* Location of rear-view camera CAUTION  The rear-view camera has a special lens that can make objects shown on the screen appear The rear-view camera (A) is integrated into to be closer or further away than they actu- the part near the rear gate handle.
Page 298 Rear-view camera*  Two Green lines (C) indicate approxi- Errors between the display and NOTE mately 20 cm outside of the vehicle body. the actual road surface  It is not possible to fully see obstacles when  Short transverse lines (1 to 3) indicate dis- the lens is dirty.
Page 299 Rear-view camera* Therefore when there is an obstacle on the B: Objects shown on the screen downward slope, it appears closer than its actual position.  When there is an upward slope behind the vehicle The reference lines are displayed closer than the actual distance.
Page 300: Multi Around Monitor
Multi Around Monitor* not use them as a guide to distances to solid cles in parking spaces and to parallel park objects. their vehicles. Example: On the screen the point B appears the nearest, then the point C and A in order of CAUTION distance.
Page 301 Multi Around Monitor* Range of view of the Multi Around Monitor E00645100122 The range of view of the Multi Around Monitor cameras is limited to the area shown in the illustrations. It cannot show around the both sides and the lower part of the front and rear bumpers, etc. While driving, be sure to visually confirm safety around the vehicle. Range of view of the Multi Around Monitor cameras Side-view camera (right) Front-view camera...
Page 302 Multi Around Monitor* Types of views of the Multi Side-view/Front-view mode Around Monitor Views of the passenger’s side of the vehicle and the front of the vehicle are displayed. Two different types of views are displayed on the left side and the right side respectively. Bird’s eye-view/Rear-view mode Views of the surroundings of the vehicle and behind the vehicle are displayed.
Page 303 Multi Around Monitor* NOTE NOTE NOTE • When the light of the sun or the light from a • Do not splash the camera with boiling  The passenger’s side screen can be switched vehicle’s headlamps shines directly into the water.
Page 304 “R” (REVERSE) posi- played correctly. Be sure to have it inspected tion with the front view displayed on the by an authorised MITSUBISHI MOTORS driver’s side screen, the driver’s side screen dealer. switches to the Rear-view mode. When you...
Page 305 Multi Around Monitor* NOTE NOTE  When the expected course lines are dis- played in the rear view, the expected course lines are also displayed in the bird’s-eye view (Front: broken line, Rear: solid line). 1- Approximately 100 cm from the rear Rear-view mode edge of the rear bumper E00645600055...
Page 306 Multi Around Monitor* Therefore when there is an obstacle on the upward slope, it appears farther than its actual position. A: Actual objects A: Actual objects B: Objects shown on the screen B: Objects shown on the screen A: Actual objects ...
Page 307 Multi Around Monitor* not use them as a guide to distances to solid objects. Example: On the screen the point B appears the nearest, then the point C and A in order of distance. The point A and B actually are the same distances from the vehicle, and the point C is farther off than the point A and B.
Page 308 Multi Around Monitor* 1. Stop the vehicle in a safe place. CAUTION NOTE  The bird’s-eye view is an simulated view  In the Bird’s eye-view mode, since the views CAUTION processed by combining view captured by captured by the four cameras, “Front-view ...
Page 309: Cargo Loads
E00609902667 shape. For details, consult a nearby author-  Before driving and after travelling a short ised MITSUBISHI MOTORS dealer. distance, always check the load to make sure Cargo loads precautions it is securely fastened to the roof carrier.
Page 310 For pleasant driving Important operation tips for the air conditioner .......7-2 Antenna ..................7-57 Ventilators ..................7-2 Link System*..................7-58 Front cooler/Manual air conditioning*..........7-6 ® Bluetooth 2.0 interface* ..............7-58 Automatic climate control air conditioner*........7-10 USB input terminal*...............7-80 Dual-zone automatic climate control air conditioner* ....7-15 HDMI terminal* ................7-84 Rear cooler*..................7-20 Sun visors ..................7-85...
Page 311: Important Operation Tips For The Air Conditioner
Important operation tips for the air conditioner  When operating the system, make sure the Important operation tips for During a long period of disuse air intake, which is located in front of the the air conditioner windscreen, is free of obstructions such as The air conditioning should be operated for at leaves and snow.
Page 312 Ventilators Rear ventilators Left Right E00775000033 1- Close 1- Close 2- Open 2- Open Front side ventilators Rear ventilators Adjusting the air flow direction Move the knob (A) to adjust the air flow E00700202121 Move the knob (A) to adjust the air flow direction.
Page 313 Ventilators NOTE NOTE  The cool air from the ventilators may appear  Be careful not to spill beverages, etc., into as a mist. the ventilators. This is due to moist air being suddenly Doing so might cause the air conditioner not cooled by the air conditioning.
Page 314 Ventilators The mode selection and air flowing from the front ventilators Face position Foot/Face position Foot position Foot/Demister position* Demister position* *: Optional equipment NOTE  On vehicle with the automatic climate control air conditioner/dual-zone automatic climate control air conditioner, when using the “ ”...
Page 315: Front Cooler/Manual Air Conditioning
Front cooler/Manual air conditioning*  Usage Demisting of the windscreen Front cooler/Manual air • Changing the position of air flowing and door windows (Manual air conditioning from the ventilators  P.7-4 * Not UK Spec • Demisting of the windscreen and door conditioning) E00731101060 windows (Manual air conditioning) →...
Page 316 Front cooler/Manual air conditioning* CAUTION Adjusting the temperature con- trol  For safety, make sure you have a clear view through all the windows. E00771600031  Do not set the temperature to the max. cool The temperature control dial is used to select position.
Page 317 Front cooler/Manual air conditioning* Manual air conditioning Cooling Heating (Manual air condition- ing) E00771800033 Select dials and levers as shown in the illus- E00775700027 tration according to your purpose. Select dials and levers as shown in the illus- tration according to your purpose. Cooler CAUTION ...
Page 318 Front cooler/Manual air conditioning* Driving in polluted outside air conditions E00775200035 If the outside air is dusty or otherwise con- taminated when driving through a tunnel or in a traffic jam, set the air selection lever to the “ ” (recirculation) position. Refer to “Switching outside air and recircu- lated air”...
Page 319: Automatic Climate Control Air Conditioner
Automatic climate control air conditioner* Automatic climate control air conditioner * Not UK Spec E00702401508 The air conditioner can only be used while the engine is running. • Operating the system in manual mode  11- Air conditioning indicator  P.7-13 1- Temperature control switch ...
Page 320 Automatic climate control air conditioner* Press the demister switch or AUTO switch or NOTE NOTE MODE switch or OFF switch to turn off the  In extreme cold, the air conditioning control  When the demister switch is pressed, the air demister mode.
Page 321 Automatic climate control air conditioner* Press the OFF switch to turn off the air condi- NOTE Adjusting the blower speed tioning system.  Never place anything on top of the interior E00772300048 air temperature sensor (B), which will pre- The mode selection, blower speed adjust- Press of the blower speed selection vent it from functioning properly.
Page 322 Automatic climate control air conditioner* NOTE Switching the air conditioning system ON/OFF  When the temperature is set to the highest or the lowest, the air selection and the air condi- E00772900057 tioner will be automatically changed as fol- Press the switch to turn the air conditioner on, lows.
Page 323 Automatic climate control air conditioner* Air is recirculated inside the passenger NOTE compartment.  When the engine coolant temperature rises to a certain level, the air selection is automati- cally switched to the recirculation position and the indicator lamp (A) comes on. At this time, the system will not switch to the out- side position even if the air selection switch is pressed.
Page 324: Dual-Zone Automatic Climate Control Air Conditioner
Dual-zone automatic climate control air conditioner* Dual-zone automatic climate control air conditioner E00773000042 The air conditioner can only be used while the engine is running. 6- Air selection switch  P.7-20 14- Passenger’s side temperature display 1- Driver’s side temperature control 7- Demister switch ...
Page 325 Dual-zone automatic climate control air conditioner* • Operating the system in automatic mode 3. Select your desired blower speed by Demisting of the windscreen  P.7-17 pressing the blower speed selection and door windows • Operating the system in manual mode  switch.
Page 326 Dual-zone automatic climate control air conditioner* NOTE NOTE  When the demister switch is pressed, the air  If the blower speed selection switch, air con- conditioning system automatically operates ditioning switch, MODE switch, or air selec- and outside air (as opposed to recirculated tion switch is operated while the system is air) is selected.
Page 327 Dual-zone automatic climate control air conditioner* Operating the system in manual Adjusting the temperature con- NOTE mode trol  The temperature value of air conditioner is switched in conjunction with outside temper- E00773300045 E00773500047 ature display unit of the multi information Blower speed and ventilator mode may be Press of the temperature control...
Page 328 Dual-zone automatic climate control air conditioner* When the AUTO switch is pressed, the NOTE NOTE “DUAL” indicator (B) will disappear, and the • When the temperature is set to the lowest  If the driver’s side temperature control temperature setting for the passenger’s side setting (18.0°C) switch is pressed when the “DUAL”...
Page 329: Rear Cooler
Rear cooler* Refer to “Switching outside air and recircu- Switching outside air and recir- CAUTION lated air” on page 7-20. culated air  Normally, use the outside position to prevent the windows from fogging up. E00773900041 Rear cooler Use of the recirculation position for To change the air selection, simply press the extended time may cause the windows to fog E00707701173...
Page 330: Customising The Air Conditioning
Customising the air conditioning To operate the rear cooler in the To operate the rear cooler in the Customising the air condi- front seat rear seat tioning E00774400030 E00774500031 E00774600061 1. Press the “ON/OFF” switch to activate the When the switch is pressed, the fan starts and For vehicle with the automatic climate con- rear cooler.
Page 331: Air Purifier
Air purifier*  Setting change method 3 sounds are emitted and the “ ” indi- NOTE Hold down the air selection switch for cator flashes 3 times.  Operation in certain conditions such as driv- approximately 10 seconds or more. •...
Page 332 For details,  Product names and other proper names comes from it, immediately turn off the access the MITSUBISHI MOTORS website. are the trademarks or registered trade- audio system. We recommend you to have it Please read and agree to the “Warning about...
Page 333 Audio system* 5th generation 5th generation 160GB (2009) 160GB (2007) 80GB (video) (video) 60GB 80GB 30GB 6th generation 5th generation 4th generation (video) 8GB 16GB (video camera) 8GB 16GB 8GB 16GB 3rd generation 2nd generation 1st generation (video) (aluminum) 1GB 2GB 4GB 4GB 8GB 2GB 4GB 8GB 7-24...
Page 334: Handling Of Discs
Handling of Discs  If discs are not going to be used for a long Important Points on Handling period of time, remove these from the product.  Fingerprints or other marks on the read surface of the disc may result in its con- 4th generation 3rd generation tent being more difficult to read.
Page 335: Audio Files (Mp3/Wma/Aac)
Audio Files (MP3/WMA/AAC)  Discs that have not been finalized cannot • There may be noise during playback. Maxi- be played back. • There may be jumping in the audio. Com- Type Size  Even if recorded using the correct format •...
Page 336 Audio Files (MP3/WMA/AAC) CAUTION Data Formats That Can Be ROOT Played Back  CD-ROM and CD-R/RW media can only Folder play back MP3 format audio files. E00736200030 Audio file  Actions such as copying audio CDs or files Data formats that can be played on discs and either distributing these to others for free (CD-ROM, CD-R/RW) and USB devices dif- or for charge, or uploading files via the Inter-...
Page 337 Audio Files (MP3/WMA/AAC) “Motion Picture Experts Group”, and this is a Speci- Speci- video compression standard used in video Name fica- Explanation Name fica- Explanation CDs, etc. tion tion MP3 is one of the audio compression meth- Format ISO96 Level Maximum 8 File name Maximum 64 bytes (for Uni-...
Page 338 Audio Files (MP3/WMA/AAC) format that has a higher compression ratio Item Details Item Details than MP3. Sampling MPEG-1: 32/44.1/48 Sampling 32/44.1/48 frequency frequency MPEG-2: 16/22.05/24 NOTE [kHz] [kHz]  Microsoft, Windows Media, and Windows Bit rate MPEG-1: 32 to 320 Bit rate 48 to 320 are registered trademarks of Microsoft Cor-...
Page 339: Important Points On Safety For The Customer
Important Points on Safety for the Customer This features 1.4x the compression of MP3, Item Details WARNING with comparable audio quality. Bit rate MPEG 8 to 320  The driver should not pay close attention [kbps] to the display while driving. CAUTION This may prevent the driver looking MPEG...
Page 340: Operation Keys
Operation Keys WARNING  Do not disassemble or modify the product. This may lead to malfunction, fire, or elec- tric shock.  During thunderstorms, do not touch the antenna or the front panel. This may lead to electrical shock from lightning.
Page 341 Operation Keys Disc slot Disc *Label side Push the disc in a certain amount, and the product will pull the disc in, and playback will start. 2. Press the key. This will eject the disc from the product, so remove the disc. CAUTION ...
Page 342 Operation Keys Explanation of Buttons E00737501239 This explains names and functions of each part. Type 1 Type 2 AH1100658 5- RADIO key 9- AUTO-P key (Type 1) Switch the radio and the band. Auto preset the radio. Use to eject a disc. 6- PWR/VOL key PTY/SCAN key (Type 2)For audio, 2- 3...
Page 343 Operation Keys 12- PAGE key Steering wheel audio remote Type 1 Display indicator page advance. control switches 13- 5 E00737601533 Play/Pause Bluetooth Audio*, and use as preset key 5 for radio. 14- 6 Return during audio track search, and stop Bluetooth Audio*. For radio, use as preset key 6.
Page 344: Listen To Radio
Listen to Radio A “Beep” sounds, and the preset key is Release the button to start Listen to Radio registered. seek station selection, and (hold down) E00737701156 when a station is received, This explains how to listen to AM and FM scanning stops.
Page 345: Listen To Traffic Messages (Type 2)
Listen to Traffic Messages (Type 2) NOTE NOTE To Listen to Traffic Messages  Separate to normal reception preset keys,  Using auto store for FM1 and FM2 switches 1. When not in MW or LW mode, press the this registers in preset keys in the AUTO-P to FM3.
Page 346: Listen To Cds
Listen to CDs 1. When not in MW or LW mode, press the Select the Track NOTE TP key.  Selecting a track, ejecting, fast forwarding, “TP” is indicated on the display, and the or rewinding will cancel. product switches to standby mode. Press the key or key to select the...
Page 347: Listen To Mp3S
Listen to MP3s This enables selection of the next or previous Repeat playback of the tracks within the Listen to MP3s track. folder currently being played. E00737901158 This explains how to listen to audio files on a NOTE Fast Forward or Rewind disc.
Page 348: Listen To An Ipod
Listen to an iPod Scan Playback (SCAN) NOTE NOTE  Select the folder, and hold down the  Depending on the generation, model, or soft- ware version of the iPod/iPhone, playback Press the SCAN key (Type 1) or PTY/SCAN /SEL key to start playback from the first on this product may not be possible.
Page 349 Listen to an iPod Repeat Playback (RPT) NOTE Play iPod  Depending on the status of the iPod/iPhone, it may take some time until the device is rec- Press the 1RPT key. Press the MEDIA key to set the iPod as the ognized, or playback starts.
Page 350: Listen To Audio Files On A Usb Device
Listen to Audio Files on a USB Device NOTE NOTE CAUTION  Pressing again will cancel.  Select the category, and hold down the  Do not use hard discs, card readers, or mem- ory readers, as damage may occur to these or /SEL key to start playback from the first to the data contained therein.
Page 351 Listen to Audio Files on a USB Device Fast forward/rewind is possible. NOTE NOTE  When connecting a USB device, use a con-  Depending on the type of USB device, usage Switch Playback Mode nection cable. Failure to use a connection may not be possible, or functions that can be cable when connecting may place undue load used may be restricted.
Page 352 Listen to Audio Files on a USB Device each of the tracks on the whole USB device 3. Turn the /SEL key to select the file. Folder Random Playback (RDM) in order. 4. Press the /SEL key. Press the 2RDM key. NOTE This plays the selected file (track).
Page 353: To Play Ipod/Usb Memory Device Tracks Via Voice Operation (Vehicles With Bluetooth 2.0 Interface)
To play iPod/USB memory device tracks via voice operation (vehicles with Bluetooth® 2.0 interface) 3. After the voice guide says “What Artist To play iPod/USB memory would you like to play?,” say the artist device tracks via voice oper- name. 4.
Page 354 To play iPod/USB memory device tracks via voice operation (vehicles with Bluetooth® 2.0 interface) 3. After the voice guide says “What Album 7. The system exits the voice recognition NOTE would you like to play?” say the album mode and starts playback. ...
Page 355: Listen To Bluetooth Audio
Listen to Bluetooth Audio 5. If there are two or more matches, the If you say “No,” the next matching genre To search by genre voice guide will say “More than one is uttered by the system. E00771300025 match was found, would you like to play 1.
Page 356 Listen to Bluetooth Audio 2. Press the 5 key. Bluetooth Audio play- CAUTION NOTE back starts.  Never hold these devices in your hand to  Depending on the status of the vehicle and operate while driving, as this is dangerous. device, the iPod/iPhone may not play back NOTE after starting the engine.
Page 357: To Listen To A Disc In The Rear-Seat Display (Vehicles With Rear-Seat Display)
To listen to a disc in the rear-seat display (vehicles with rear-seat display) Repeat Playback (RPT) NOTE To listen to a disc in the  Pressing again will cancel. rear-seat display (vehicles Press the 1RPT key. with rear-seat display) Repeat playback of the track currently being Scan Playback (SCAN) E00755100168 played.
Page 358 Display Indicator Change the Display Mode NOTE During MP3/WMA/AAC Play- back  Up to 11 characters may be displayed at one E00738501164 time. To display 12 or more characters, press You can change the content of the display the PAGE key, and subsequent characters indicator.
Page 359: Audio Quality And Volume Balance Adjustment
Audio Quality and Volume Balance Adjustment [DISP] Each time the key is pressed, this ® Vehicles equipped with premium audio During Bluetooth 2.0 Audio Play- switches in the order “Album name”, “Track Adjust- back Turn counter- Turn clock- name”, “Artist name”, “Genre name”*, and ment clockwise wise...
Page 360: System Settings
System Settings Except for vehicles equipped with pre- 2. Press the /SEL key to select settings Adjust- Turn counter- Turn clock- mium audio items. ment clockwise wise items Adjust- Turn counter- Type 1 ment Turn clockwise BAL- LEFT 11 to CENTER to clockwise items...
Page 361 System Settings Settings Settings Settings Settings RDS Setting (Type 2) Settings content Settings content name value name value TP-S* TP-S ON Automatically ENGLISH Set the display lan- Change RDS settings. search for traffic guage for the pro- messages (TP sta- gram content (“Set value”...
Page 362 System Settings 3. Press the /SEL key. Settings Settings NOTE Settings content name value  Cancel functions such as the mobile phone This completes the adjustment. ITALIANO Set the display lan- “dial lock”, and connect while on the standby screen. guage for the pro- NOTE ...
Page 363 System Settings NOTE ® ® Vehicles without a Bluetooth 2.0 Inter- Vehicles with a Bluetooth 2.0 Interface face  Depending on the vehicle model, this may (“Set value” bold typeface indicates factory not display. A hands-free kit (available separately) is default settings.) required.
Page 364: Troubleshooting
The drive has malfunctioned for some reason. Check that there is no problem with the disc, and insert the disc again. If the problem persists, con- sult an authorised MITSUBISHI MOTORS dealer. HEAT ERROR The temperature inside the product is high.
Page 365 Turn the power OFF and wait a short while. If the problem persists, consult authorised LSI ERROR There is an internal malfunction for some reason. MITSUBISHI MOTORS dealer. UNSUPPORTED Unsupported audio files have been played. Confirm audio files that can be played.  “Audio Files (MP3/WMA/AAC)” (P.7-26) FORMAT UNSUPPORTED An unsupported USB device has been connected.
Page 366: Antenna
Antenna Symptoms Cause Response The disc cannot be A disc is already in the product. Eject the disc.  “Insert/Eject Discs” (P.7-31) inserted. There is no disc in the product, but the prod- Press the eject button once.  “Insert/Eject Discs” (P.7-31) uct says it is loading.
Page 367: Link System
2.0 inter- apply a film. You have acquired a device that includes soft- ® face, you must pair the Bluetooth device ware licensed by MITSUBISHI MOTORS ® and Bluetooth 2.0 interface. Refer to “Con- CORPORATION from Visteon Corporation, ® necting the Bluetooth 2.0 interface and...
Page 368: Bluetooth® 2.0 Interface
2.0 interface, you can see to access  Refer to and comply with all state and via the MITSUBISHI MOTORS website. local laws in your area regarding cellular Please read and agree the “Warning about phone usage while driving.
Page 369 Bluetooth® 2.0 interface* Industry Canada Rules. Operation is subject Volume down switch Steering control switch and to the following two conditions: microphone Used to decrease the volume.  This device may not cause harmful inter- E00727201565 ference.  This device must accept any interference SPEECH button received, including interference that may cause undesired operation.
Page 370 Bluetooth® 2.0 interface* • In such circumstances, you can press the NOTE Except for vehicles for Chile and Mexico button briefly to switch between callers.  Call waiting and three-way calls can be used You will switch to the first caller and the ®...
Page 371 Bluetooth® 2.0 interface* 6. When the voice guide says “English Selecting the language NOTE (French, Spanish, Italian, German, Dutch,  Changing the language deletes the mobile Portuguese or Russian) selected,” the lan- ® phonebook imported to the Bluetooth guage change process will be completed ...
Page 372 Bluetooth® 2.0 interface* If you are anywhere else within the system, 6. For confirmation purposes, the voice Security function (Except for vehi- say “Cancel” to return to the main menu. guide will say “Password <4-digit pass- cles for Chile and Mexico) word>.
Page 373 Bluetooth® 2.0 interface* If the entered password is wrong, the voice 5. When the disabling of the password is 5. The voice guide will say “Please say a 4- guide will say “<4-digit password>, Incorrect completed, the voice guide will say “Pass- digit passcode.
Page 374 Bluetooth® 2.0 interface* code to continue” when the SPEECH button 4. The voice guide will say “Passcode is phone while in speaker enrolment to prevent is pressed to enter voice recognition mode. enabled. Would you like to disable it?” interruption of the process. Say the 4-digit passcode number to enter the Answer “Yes.”...
Page 375 Bluetooth® 2.0 interface* Say “Retrain” to start the speaker enrol- NOTE NOTE ment process and recreate a new voice  If you do not start the speaker enrolment pro-  Completing the speaker enrolment process model. (Refer to “Speaker enrolment” on cess within 3 minutes after pressing the will turn on the voice model automatically.
Page 376 Bluetooth® 2.0 interface* ® matically connected to the Bluetooth NOTE NOTE interface.  The pairing code entered here is only used  The following procedure ( ) can also ® be used instead of saying “Pair Device.” for the Bluetooth connection certification.
Page 377 Bluetooth® 2.0 interface* 7. The voice guide will say “Pairing Com- 8. The voice guide will say “Do you want to NOTE plete. Would you like to import the con- pair a device now?” Answer “Yes,” the  If you enter the wrong number, the voice tacts from your mobile device now?”...
Page 378 Bluetooth® 2.0 interface* When the confirmation function is on, the 4. After the voice guide says “Please say,” Deleting a device system will ask you again whether the the numbers of the music players and phone that you want to connect to is cor- device tags of corresponding music play- Use the following procedure to delete a rect.
Page 379 Bluetooth® 2.0 interface* 7. The voice guide will say “Deleted,” and To hear the list again from the beginning, 1. Press the SPEECH button. then the system will end the device dele- answer “Yes.” 2. Say “Setup.” tion process. When you are done, answer “No” to 3.
Page 380 Bluetooth® 2.0 interface* When the change is complete, the voice Receiving calls P.7-73 ® The Bluetooth 2.0 interface will then guide will say “New name saved” and Mute function P.7-73 make the call. then the system will return to the main Switching between hands-free mode and pri- When the confirmation function is on, the menu.
Page 381 Bluetooth® 2.0 interface* 1. Press the SPEECH button. NOTE NOTE 2. Say “Call.”  If you say “No” to all names read by the sys-  If the name you selected has matching data tem, the voice guide will say “Name not in the mobile phonebook but no telephone NOTE found, returning to main menu”...
Page 382 Bluetooth® 2.0 interface* 2. Say “Redial.” To receive the call, press the PICK-UP button Phonebook function on the steering wheel control switch. E00763700017 When the call is over, the audio system will Send function ® return to its previous state. The Bluetooth 2.0 interface has 2 types of E00761300035...
Page 383 Bluetooth® 2.0 interface* Names and telephone numbers can be NOTE NOTE changed later on.  If the maximum number of entries are  In the case of English, the system will recog- already registered, the voice guide will say nise both “zero” and “oh” (Letter “o”) for the The vehicle phonebook can be used with all “The phonebook is full.
Page 384 Bluetooth® 2.0 interface* 3. The voice guide will say “Select one of  To select and transfer one phone- NOTE the following: new entry, edit number, book entry from the phonebook of ®  If the Bluetooth 2.0 interface cannot recog- edit name, list names, delete, erase all, or the cellular phone ®...
Page 385 Bluetooth® 2.0 interface* Answer “No,” the voice guide will say 3. The voice guide will say “Select one of NOTE “Name please.” Register a different name. the following: new entry, edit number,  If the telephone number is already registered 9.
Page 386 Bluetooth® 2.0 interface* 3. The voice guide will say “Select one of 2. Say “Phonebook.” 2. Say “Phonebook.” the following: new entry, edit number, 3. The voice guide will say “Select one of 3. The voice guide will say “Select one of edit name, list names, delete, erase all, or the following: new entry, edit number, the following: new entry, edit number,...
Page 387 Bluetooth® 2.0 interface* 4. For confirmation purposes, the voice ® The Bluetooth 2.0 interface automatically NOTE guide will ask “Are you sure you want to converts from text to voice the names regis-  To delete the telephone numbers from all erase everything from your hands-free tered in the transferred phonebook entries, locations, say “All.”...
Page 388 Bluetooth® 2.0 interface* 5. The voice guide will say “Importing the 6. When the transfer is complete, the voice NOTE contact list from the mobile phonebook. guide will say “Import complete” and  All or part of data may not be transferred, This may take several minutes to com- then the system will return to the main even when the cellular phone supports Blue-...
Page 389: Usb Input Terminal
USB input terminal* Enrolment commands E00732401493 Except for vehicles for Chile and Mexico Vehicles for Chile and Mexico USB input terminal E00761901634 You can connect your USB memory device or iPod* to play music files stored in the USB memory device or iPod. *: “iPod”...
Page 390 USB input terminal* This section explains how to connect and Type 1 Type 1 remove a USB memory device or iPod. Vehicles without See the following sections for details on how Vehicles without DVD AUDIO to play music files. DVD AUDIO Refer to “Listen to an iPod”...
Page 391 USB input terminal* 5. To remove the USB connector cable, turn Type 1 the ignition switch to the “LOCK” posi- Vehicles without tion or put the operation mode in OFF DVD AUDIO first and perform the installation steps in reverse. CAUTION Vehicles with DVD ...
Page 392 “Listen to Audio Files on a USB Device” on function. page 7-41 “Audio Files (MP3/WMA/AAC)” on page 7-26. In some countries, for connectable device types for “iPod*,” “iPod classic*,” “iPod nano*,” “iPod touch*” and “iPhone*,” access the MITSUBISHI MOTORS website. For pleasant driving 7-83...
Page 393: Hdmi Terminal
HDMI terminal* Please read and agree to the “Warning about NOTE HDMI terminal Links to the Web Sites of Other Companies”.  Do not connect to the USB input terminal The websites mentioned above may connect E00771400084 any device (hard disk, card reader, memory you to websites other than the MITSUBISHI You can connect a commercially available reader, etc.) other than the connectable...
Page 394: Sun Visors
Sun visors NOTE CAUTION Type 2  For details, refer to the separate owner’s  After removing the HDMI cable, be sure to manual for a DVD AUDIO and Smartphone close the terminal cover (Type 1) or the floor Link Display Audio. console box (Type 2).
Page 395: Vanity Mirror
Vanity mirror Ashtray Mounting position for movable ashtray E00711402312 CAUTION The movable ashtray can be fitted in the cup  Put out matches and cigarettes completely holder of the front seat and second seat. before they are placed in the ashtray. Refer to “Cup holder”...
Page 396: Cigarette Lighter
Cigarette lighter* To use a plug-in type accessory, remove the Cigarette lighter CAUTION cap or open the lid, and insert the plug in the  Do not touch the heating element or the ciga- accessory socket. E00711502746 rette lighter housing, hold the knob only to The cigarette lighter can be used while the prevent burns.
Page 397: Interior Lamps
Interior lamps Interior lamps Front room & map lamps/Rear For the third seat personal lamps E00712002445 E00717301781 Front room & map lamps Except for vehicles with sunroof CAUTION  Be sure to use a “plug-in” type accessory 1- Front room & map lamps operating at 12 V and at 120 W or less.
Page 398 Interior lamps Position Position Rear personal lamps of lamp On/off control of lamp On/off control switch switch Except for vehicles with rear cooler 2- Door Delayed off function Auto cut-out function () The lamps illuminates when a If the lamps is left switched on door or the tailgate is opened.
Page 399  The time until the lamp goes off (delayed off) can be adjusted. For details, please con- Type 2 Luggage compartment lamp sult an authorised MITSUBISHI MOTORS dealer. E00712701836  The auto cut-out function cannot be operated when the front room lamp switch is in the “...
Page 400: Storage Spaces
Storage spaces Storage spaces Glove box 3- ( The lamp goes off regardless of whether the E00717602853 E00713103352 tailgate is open or closed. The glove box can be locked and unlocked CAUTION using the key. Door courtesy lamps  Never leave lighters, canned carbonated bev- erage, and spectacles in the cabin when park- E00717501220 ing the vehicle in hot sunshine.
Page 401 Storage spaces Centre console under tray NOTE  When using a commercially available USB E00748600086 connector cable connected to the USB input The centre console under tray is on the floor terminal or commercially available HDMI console part. connector cable connected to the HDMI input terminal, if you hold up extra length of the cable in the storage space and install the tray, you can use only the necessary length...
Page 402 Storage spaces Luggage floor boxes E00718701883 To use the box, raise the luggage floor board. A- Tray NOTE  When opening or closing the lid, be careful NOTE not to trap hands.  The tray can be stored in the floor console ...
Page 403: Cup Holder
Cup holder CAUTION NOTE Type 2  The holder should not be used to store any-  Some bottles may not be fastened tightly thing heavier than sunglasses. These objects depending on the shape. could drop out. Before using the cup holder, make sure the some bottles are tightly fastened to the cup holder.
Page 404: Bottle Holder
Bottle holder The bottle holders are provided at both sides For the third seat Bottle holder of front and rear doors. E00719001157 E00718201497 The cup holder is located at the right side of WARNING the third seat.  Do not spray water or spill beverages The cup holder is designed for holding cups inside the vehicle.
Page 405 Cargo area cover (5 persons)* CAUTION  If the second seatback or seatback lock lever strongly touches the cover, move the cover rearward or adjust the seatback forward. The cover could break if it supports the seat- back of the second seat. To remove 1.
Page 406: Convenient Hook
Convenient hook Convenient hook E00732901270 Light items of luggage can be hung from the hook. CAUTION WARNING  Do not use the assist grips when getting into  Do not put a hanger or any heavy or or out of the vehicle. The assist grips could pointed object on the coat hook.
Page 407: Luggage Net (5 Persons)
Luggage net (5 persons)* Use the hooks on the floor for securing the Third seatback (7 persons) NOTE luggage.  Do not hang heavy luggage (more than approximately 4 kg) on the hook (Side). Fold the third seatback, pull up the cover (A). CAUTION Doing so could cause damage to the hook.
Page 408 For emergencies If the vehicle breaks down ...............8-2 Emergency starting ................8-2 Engine overheating ................8-4 Bleeding the fuel system (diesel-powered vehicles) .......8-5 Removal of water from the fuel filter (diesel-powered vehicles) ............8-5 Tools, jack and jack handle ..............8-6 How to change a tyre ...............8-8 Towing ...................8-15 Operation under adverse driving conditions ........8-19...
Page 409: If The Vehicle Breaks Down
If the vehicle breaks down 3. Set the parking brake firmly on each vehi- If the vehicle breaks down WARNING cle. Put an A/T in “P” (PARK) or a M/T in  To start the engine using jumper cables E00800102411 “N”...
Page 410 Emergency starting Diesel-powered vehicles (4D56) 5. Connect one end of one jumper cable WARNING to the positive (+) terminal of the dis-  Make sure that the connection is made charged battery (A or B), and the other to the appointed position (shown in the to the positive (+) terminal of the illustration).
Page 411: Engine Overheating
[If the cooling fans are not turning] 2. Check whether steam is coming from the Stop the engine immediately and contact engine compartment. an authorised MITSUBISHI MOTORS dealer for assistance. [If steam does not come from the engine compartment] For emergencies...
Page 412: Bleeding The Fuel System (Diesel-Powered Vehicles)
Bleeding the fuel system (diesel-powered vehicles) If there is anything wrong with the cool- CAUTION ing system or drive belt, have the problem  Do not smoke or have any other open flame corrected at an authorised MITSUBISHI near the vehicle while bleeding the fuel sys- MOTORS dealer.
Page 413: Tools, Jack And Jack Handle
ON. If in doubt, consult your nearest author- 2. Operate the hand pump (B) slowly 6 or ised MITSUBISHI MOTORS dealer. 7 times in order to force the water out through the drain plug (A).
Page 414 Tools, jack and jack handle Tools and jack handle E00801902113 2. Remove the securing band (C), and then 4. Reverse the removing procedure when take out the tools and jack handle (D). storing the tools, jack and jack handle. 1- Tool bag 2- Wheel nut wrench NOTE 3- Tyre inflation pressure gauge*...
Page 415: How To Change A Tyre
How to change a tyre How to change a tyre E00801204107 Before changing a tyre, first stop your vehicle in a safe, flat location. 1. Park the vehicle on level and stable ground, free of loose pebbles, etc. 2. Set the parking brake firmly. 3.
Page 416 How to change a tyre Spare wheel information To remove the spare wheel Except for vehicles with luggage floor box E00803601885 E00803501666 The spare wheel is stored under the rear of CAUTION LOCK the body.  When removing the spare wheel, put on Check the air pressure of the spare tyre fre- gloves.
Page 417 How to change a tyre CAUTION • Do not use the power tool. Use the wheel nut wrench stowed on the vehicle. • Do not apply a force of 200 N or more at the end of the wheel nut wrench. 5.
Page 418 How to change a tyre WARNING  Do not use the jack on a tilted or soft sur- face. Otherwise, the jack might slip and cause personal injury. Always use the jack on a flat, hard surface. Before setting the jack, make sure there are no sand or peb- bles under the jack base.
Page 419 How to change a tyre 7. Clean out any mud, etc. on the hub sur- NOTE face (G), hub bolts (H) or in the installa-  This jack is a 2 stage expansion type. tion holes (I) in the wheel, and then mount the spare wheel.
Page 420 How to change a tyre Tighten the wheel nuts until the tapered Using the jack handle, turn the release parts of the wheel nuts make light contact valve anticlockwise slowly to lower the with the seats of the wheel holes and the vehicle until the tyre touches the ground.
Page 421  If the steering wheel vibrates when driving after changing the tyre, have the tyre checked for balance at your nearest author- ised MITSUBISHI MOTORS dealer.  Do not mix one type of tyre with another or use a different size from the one listed. This would cause early wear and poor handling.
Page 422: Towing
MITSUBISHI MOTORS dealer or a com- • Do not use the power tool. mercial tow truck service. Use the wheel nut wrench stowed on the In the following cases, transport the vehicle vehicle.
Page 423 CAUTION tow the vehicle. Please contact your author-  On 4WD vehicles, be sure to shift the trans- ised MITSUBISHI MOTORS dealer or a fer shift lever or set the drive mode-selector commercial tow truck service for assistance. to “2H” position and transport the vehicle...
Page 424 Towing Towing with rear wheels off the CAUTION ground (Type C)  If you tow the vehicles with A/T with the driving wheels on the ground (Type B) as illustrated, make sure that the towing speed Place the gearshift lever in the “N” (Neutral) distance given below...
Page 425 Towing 5. Turn on the hazard warning lamps if 2. Keep the engine running. CAUTION If the engine is not running, perform the required by law. (Follow the local driving  When the vehicle with an A/T is to be towed following operation to unlock the steering laws and regulations.) by another vehicle with the all wheels on the...
Page 426: Operation Under Adverse Driving Conditions
 Avoid high-speed operation, sudden faults. After driving flooded roads, be sure to acceleration, abrupt brake application and have an inspection at an authorised sharp cornering. MITSUBISHI MOTORS dealer and take the necessary measures or repair. For emergencies 8-19...
Page 427 Operation under adverse driving conditions  Depressing the brake pedal during travel CAUTION on snowy or icy roads may cause tyre  The impact on tyres and/or wheels when slippage and skidding. When traction driving on a bumpy or rutted road can dam- between the tyres and the road is reduced age the tyre and/or wheel.
Page 428 Vehicle care Vehicle care precautions ..............9-2 Cleaning the interior of your vehicle ..........9-2 Cleaning the exterior of your vehicle ..........9-3...
Page 429 Vehicle care precautions 2. Dip cloth in fresh water and wring it out Vehicle care precautions Cleaning the interior of your well. Using this cloth, wipe off the deter- vehicle E00900102005 gent thoroughly. In order to maintain the value of your vehicle, E00900201735 NOTE it is necessary to perform regular mainte-...
Page 430 Cleaning the exterior of your vehicle Use a vacuum cleaner and brush to clean the paint coat and body of your vehicle if left NOTE the seats. If stained, vinyl and synthetic in prolonged contact.  Remove dirty patches or oil substances leather should be cleaned with an appro- Frequent washing and waxing is the best way quickly as they can stain genuine leather.
Page 431 Cleaning the exterior of your vehicle CAUTION CAUTION Waxing  Never spray or splash water on the electrical • The outside rear-view mirrors are retracted. E00901001987 components in the engine compartment. • The roof antenna is removed. Waxing the vehicle will help prevent the Doing so could have an adverse effect on the •...
Page 432 Cleaning the exterior of your vehicle the glass, wipe it dry with a clean, dry, soft Cleaning plastic parts Aluminium wheels cloth. Never use a cloth that is used for clean- E00901301906 E00901501621 ing a painted surface to clean a window. Wax 1.
Page 433 Cleaning the exterior of your vehicle NOTE  The surface treatment on the inside of the glass may be removed if hard cloth or organic solvent (benzine, kerosene, thinner, etc.) is used. Engine compartment E00902100324 Clean the engine compartment at the begin- ning and end of winter.
Page 434 Maintenance Service precautions ................10-2 Catalytic converter .................10-4 Bonnet ....................10-4 Engine oil ..................10-5 Engine coolant ................10-7 Washer fluid ...................10-9 Brake fluid ..................10-9 Clutch fluid* .................10-10 Power steering fluid ..............10-11 Battery ..................10-11 Tyres ....................10-13 Wiper blade rubber replacement ..........10-20 General maintenance ..............10-21 Fusible links .................10-22 Fuses ....................10-22 Replacement of lamp bulbs ............10-27...
Page 435: Service Precautions
 When checking or servicing the inside of your personal safety. Consult an author- the engine compartment, make sure the ised MITSUBISHI MOTORS dealer for engine is switched off and has had a necessary information. chance to cool down.
Page 436 Service precautions Check items of engine compartment are located as shown in the figure below. Petrol-powered vehicles Diesel-powered vehicles (4D56) Diesel-powered vehicles (4N15) 2. Brake fluid reservoir 3. Clutch fluid reservoir* 1. Engine coolant reservoir Maintenance 10-3...
Page 437: Catalytic Converter
Catalytic converter 4. Power steering fluid reservoir Bonnet NOTE 5. Engine oil level gauge  Only open the bonnet when the wipers are in E01000304373 6. Engine oil cap the parked position. Failure to do so may 7. Washer fluid reservoir cause damage to the bonnet, wiper arms or To open 8.
Page 438: Engine Oil
Engine oil To close NOTE (4D56) Diesel-powered vehicles  If this does not close the bonnet, release it 1. Unlatch the support bar and clip it in its from a slightly higher position. holder.  Do not press down the bonnet hard with a hand as it may damage the bonnet.
Page 439 Engine oil The engine oil used has a significant effect on NOTE NOTE the engine’s performance, service life and  Check or refill the oil according to the fol-  For handling of used engine oils, refer to startability. Be sure to use oil of the recom- lowing manner.
Page 440: Engine Coolant
It “For service CD” or higher may result in failure of the mechanical If those classifications are not available, con- assembly. tact an authorised MITSUBISHI MOTORS NOTE dealer.  Use of additives is not recommended since Diesel-powered vehicles...
Page 441 If this occurs, have Anti-freeze Petrol-powered vehicles, Diesel-powered the system checked at an authorised concentration vehicles (4N15) MITSUBISHI MOTORS dealer as soon as possible. (Diesel-pow- Use “MITSUBISHI MOTORS GENUINE If the level should drop below the “L” (LOW) ered vehicles)
Page 442: Washer Fluid
If this occurs, have the vehicle checked by an The concentration should be checked before anti-freezing agent. authorised MITSUBISHI MOTORS dealer. the start of cold weather and anti-freeze added to the system if necessary. Maintenance...
Page 443: Clutch Fluid
 Clean the filler cap before removing and close the cap securely after maintenance. A rapid fluid loss indicates a leak in the clutch system which should be inspected by your authorised MITSUBISHI MOTORS dealer and repaired immediately. 10-10 Maintenance...
Page 444: Power Steering Fluid
Fluid type water and immediately see a doctor. observe the following cautions for safety. If you accidentally swallow battery elec- Use “MITSUBISHI MOTORS GENUINE trolyte, immediately see a doctor. PSF (Power Steering Fluid)”. If battery electrolyte splashes on your clothing or on the vehicle, rinse it off with lots of water.
Page 445 Battery The inside of the battery is divided into sev- WARNING Disconnection and connection eral compartments; remove the cap from each  Explosive gas compartment and fill to the upper mark. Do To disconnect the battery cable, stop the not top up beyond the upper mark because engine, first disconnect the negative (−) ter- spillage during driving could cause damage.
Page 446: Tyres
Tyres WARNING CAUTION Tyres  The battery electrolyte is extremely caus-  Do not bring the nearby parts, the plastic E01001301496 tic. Do not allow it to come in contact with parts and so on into contact with sulphuric WARNING your eyes, skin, clothing, or the painted acid (battery electrolyte) which may crack, surfaces of the vehicle.
Page 447 Tyres Speed symbol NOTE NOTE A symbol indicating the range of  Depending on the type of tyre, the markings  Temporary spare tyres are high pressure speeds at which a tyre can carry a described below may not be shown in the compact spares designed for temporary load corresponding to its load index sidewall of the tyre.
Page 448 Tyres EXAMPLE: DOT MA L9 ABCD 1515 Maximum Load Treadwear, Traction and Temper- Department of Transportation ature Grades This symbol certifies that the tyre Maximum load indicates the maximum load is in compliance with the U.S. this tyre is designed to carry. Treadwear Department of Transportation tyre safety standards, and is approved...
Page 449 Tyres on a specified indoor laboratory test wheel. passenger car tyres must meet under the Fed- Temperature Sustained high temperature can cause the eral Motor Vehicle Safety Standard No. 109. material of the tyre to degenerate and reduce Grades B and A represent higher levels of The temperature grades are A (the highest), B tyre life, and excessive temperature can lead performance on the laboratory test wheel than...
Page 450 Tyres NOTE NOTE  If the tyre inflation pressure gauge is angled  One side of the scale shows the pressure in (not straight) relative to the tyre valve, air kPa. The other side shows the pressure in will leak and accurate measurement will not kgf/cm².
Page 451 Consult your authorised safety. minimum requirement for use. When these MITSUBISHI MOTORS dealer to determine Refer to “Tyres and wheels” on page 11-10. wear indicators appear, the tyres must be the cause of irregular tread wear.
Page 452 Tyres CAUTION Snow tyres NOTE  If the tyres have arrows (A) indicating the  If flange nuts are used on your vehicle, E01002002279 correct direction of rotation, swap the front change to tapered nuts when steel wheels are The use of snow tyres is recommended for and rear tyres on the left hand side of the used.
Page 453: Wiper Blade Rubber Replacement
Wiper blade rubber replacement CAUTION Wiper blade rubber replace-  Choose a clear straight stretch of road where ment you can pull off and still be seen while you E01008201436 are fitting the chains.  Do not fit chains before you need them. This Windscreen wiper blades will wear out your tyres and the road surface.
Page 454: General Maintenance
 If you see a suspicious fuel leak or if you smell fuel, do not operate the vehicle; call 1. Lift the wiper arm off the window glass. your authorised MITSUBISHI MOTORS 2. Pull the wiper blade downward to disen- dealer for assistance.
Page 455: Fusible Links
In case of a melted fusible link, see your of the driver’s seat at the position shown in authorised MITSUBISHI MOTORS dealer the illustration. for inspection and replacement. Pull the fuse lid to remove it.
Page 456 Fuses 2. While pressing the side of the glove box, Engine compartment NOTE unhook the left and right hooks (A) and  Spare fuses are provided in the fuse block of lower the glove box. the engine compartment. Always use a fuse In the engine compartment, the fuse block is of the same capacity for replacement.
Page 457 Fuses Sym- Capac- Sym- Capac- Engine compartment fuse location Electrical system Electrical system ities ities table Electronic con- Tail lamp (right) 7.5 A E01008002066 20 A trolled unit Outside rear-view Engine compartment fuse location 7.5 A mirrors *: Fusible link Engine control unit 7.5 A ...
Page 458 Fuses Electrical sys- Capac- Electrical sys- Capac- Behind of the fuse block cover Symbol Symbol ities ities Headlamp low DC-DC(A/T) 30 A 15 A beam (left) — — — Headlamp low 15 A Engine 20 A beam (right) Fuel pump 15 A Steering heater 15 A...
Page 459 Have E01008100366 your vehicle checked by an authorised Capacity Colour MITSUBISHI MOTORS dealer. 7.5 A Brown 3. Referring to the fuse load capacity table, 10 A 4. Insert a new fuse of the same capacity by check the fuse pertaining to the problem.
Page 460: Replacement Of Lamp Bulbs
When replacing a bulb, wait for it to cool these procedures be carried out by an author- sufficiently before touching it. You could ised MITSUBISHI MOTORS dealer. otherwise be burnt.  Be careful not to scratch the vehicle body  Handle halogen lamp bulb with care. The gas when removing a lamp or lens.
Page 461 MITSUBISHI MOTORS dealer. Except for vehicles with LED headlamps :Have the lamps bulbs replaced • Headlamps (Vehicles with LED headlamps) at an authorised MITSUBISHI MOTORS 1- Position lamps: 5 W (W5W) • Side turn-signal lamps dealer. 2- Front turn-signal lamps: 21 W •...
Page 462 Replacement of lamp bulbs Inside NOTE 6B31, 4D56  When moving the upper cover towards the E01003403411 rear of the vehicle, remove the harness from the air cleaner hooks (C). 6B31, 4D56 4N15 1- Glove box lamp: 1.4 W 2- Front room & map lamps: 5 W 4N15 3- Rear personal lamps (Vehicles with rear cooler): 5 W...
Page 463 Replacement of lamp bulbs NOTE 4N15  After replacing the bulb in case of diesel- powered vehicles, make sure that the hinges at the front of the vehicle are firmly set. *: Front of the vehicle 4. To install the bulb, perform the removal steps in reverse.
Page 464 Replacement of lamp bulbs NOTE NOTE Front turn-signal lamps  When moving the upper cover towards the  After replacing the bulb in case of diesel- E01003802359 1. When replacing the bulb on the right side rear of the vehicle, remove the harness from powered vehicles, make sure that the hinges the air cleaner hooks (C).
Page 465 Replacement of lamp bulbs NOTE NOTE Front fog lamps/Daytime run- ning lamps  When moving the upper cover towards the  After replacing the bulb in case of diesel- rear of the vehicle, remove the harness from powered vehicles, make sure that the hinges E01004003254 the air cleaner hooks (C).
Page 466 Replacement of lamp bulbs 3. Remove the screws (C), and then move NOTE Front fog lamp Daytime running lamp the lamp unit towards the rear of the vehi-  When unfastening the screws of the fog cle to unfix the notch (D) and pins (E) of lamp, be careful not to mistakenly move the the lamp unit.
Page 467 Replacement of lamp bulbs G- Rear turn-signal lamp Remove the bulb by pulling it out. H- Reversing lamp Remove the bulb by pulling it out. 5. To install the bulb, perform the removal steps in reverse. NOTE  When installing the lamp unit, align the notch (J) and pin (K) on the lamp unit with the clip (L) and hole (M) in the body.
Page 468 Specifications Vehicle labeling ................11-2 Vehicle dimensions ................11-4 Vehicle performance ..............11-5 Vehicle weight ................11-5 Engine specifications ..............11-9 Electrical system ................11-10 Tyres and wheels ................11-10 Refill capacities ................11-11...
Page 469: Vehicle Labeling
Vehicle labeling Vehicle labeling Type 2 E01100104776 Vehicle Identification Number: (VIN) The vehicle identification number is stamped as shown in the illustration. The plate shows model code and engine model, transmission model and body colour Vehicle information code plate code, etc. E01102200050 Please use this number when ordering The vehicle information code plate is located...
Page 470 Vehicle labeling 6- Interior code Diesel-powered vehicles (4N15) 7- Option code Engine model/number E01102500095 The engine model and number are stamped on the engine cylinder block as shown in the illustrations. Petrol-powered vehicles 1- Production year and month 2- Identification number Certification plate (Vehicles for 3- Category Gulf countries only)
Page 471: Vehicle Dimensions
Vehicle dimensions Vehicle dimensions E01100204517 Front track 1,520 mm Overall width 1,815 mm Front overhang 880 mm Wheel base 2,800 mm Rear overhang 1,105 mm Overall length 4,785 mm Ground clearance (unladen) 218 mm Without roof rails 1,800 mm Overall height (unladen) With roof rails 1,805 mm...
Page 472: Vehicle Performance
Vehicle performance Body 6.0 m Minimum turning radius Wheel 5.6 m Vehicle performance E01100303931 Diesel-powered vehicles Item Petrol-powered vehicles 4D56 4N15 Maximum speed 182 km/h 168 km/h 166 km/h 180 km/h Vehicle weight E01100408214 Petrol-powered vehicles Item Seating capacity 5 persons 7 persons 5 persons 7 persons...
Page 473 Vehicle weight : Vehicles for Gulf countries : Vehicles for Mexico Diesel-powered vehicles (4D56) Item Seating capacity 5 persons 7 persons 5 persons 7 persons Without optional 1,860 kg 1,900 kg 1,870 kg 1,910 kg parts Kerb weight With full optional 1,930 kg, 1,925 kg* 1,970 kg 1,940 kg, 1,935 kg*...
Page 474 Vehicle weight Item Seating capacity 5 persons 7 persons 5 persons 7 persons Without optional 1,960 kg 2,000 kg 1,970 kg 2,010 kg, 2,015 kg* parts Kerb weight With full optional 2,025 kg 2,070 kg 2,035 kg 2,080 kg parts Maximum gross vehicle weight 2,710 kg Front...
Page 475 Vehicle weight Item Seating capacity 5 persons 7 persons 5 persons 7 persons Front 1,260 kg Maximum axle weight Rear 1,600 kg Maximum roof load 80 kg : Vehicles with 2 Batteries : Vehicles with diesel particulate filter (DPF) : Vehicles for South Africa : RHD vehicles Item Seating capacity...
Page 476: Engine Specifications
Engine specifications Item Seating capacity 5 persons 7 persons 5 persons 7 persons Maximum roof load 80 kg : Vehicles with 2 Batteries : Vehicles with diesel particulate filter (DPF) : Vehicles for South Africa : RHD vehicles Engine specifications E01100604364 Diesel-powered vehicles Item...
Page 477: Electrical System
*: Optional equipment Tyres and wheels E01100904569 Tyre 265/70R16 112S 265/60R18 110H Size 16x7J, 16x7JJ 18x7 1/2J Wheel Offset 38 mm NOTE  Contact an authorised MITSUBISHI MOTORS dealer for details on the combination used on your vehicle. 11-10 Specifications...
Page 478: Refill Capacities
Refill capacities E01101306737 Petrol-powered vehicles Item Quantity Lubricants Engine coolant MITSUBISHI MOTORS GENUINE SUPER LONG LIFE 9.0 litres [Includes 0.65 litre in the reserve tank] COOLANT PREMIUM or equivalent* Brake fluid As required Brake fluid DOT3 or DOT4 Oil pan 4.0 litres...
Page 479 Refill capacities CAUTION  For the A/T fluid, use only the MITSUBISHI MOTORS GENUINE ATF. Use of a different fluid could damage the transmission. Item Quantity Lubricants MITSUBISHI MOTORS GENUINE NEW MULTI GEAR Transfer oil 1.34 litres OIL ECO API classification GL-4, SAE 75W-80...
Page 480 Refill capacities Diesel-powered vehicles 4D56 4N15 Specifications 11-13...
Page 481 4D56 10.9 litres MITSUBISHI MOTORS GENUINE ATF-PA A/T fluid 4N15 12.8 litres MITSUBISHI MOTORS GENUINE ATF-MA1 CAUTION  For the A/T fluid, use only the MITSUBISHI MOTORS GENUINE ATF. Use of a different fluid could damage the transmission. 11-14 Specifications...
Page 482 MITSUBISHI MOTORS GENUINE NEW MULTI GEAR 6M/T 2.2 litres OIL ECO API classification GL-4, SAE 75W-80 MITSUBISHI MOTORS GENUINE MTF API classifica- tion GL-3 SAE 75W-85 or MITSUBISHI MOTORS GEN- 5M/T 2.5 litres UINE Multi Gear Oil API classification GL-4 SAE 75W- Transfer oil...
Page 483 Refill capacities Item Quantity Lubricants Without rear cooler 530-570 g Refrigerant (Air conditioning) HFC-134a With rear cooler 770-810 g *: Similar high quality ethylene glycol based non-silicate, non-amine, non-nitrate and non-borate coolant with long life hybrid organic acid technology 11-16 Specifications...
Page 484 Alphabetical index Manual air conditioning ....7-6 Handling of Discs ......7-25 Numerics Rear cooler ........7-20 Important Points on Safety for the Custom- er ..........7-30 4-wheel drive operation ....... 6-66 Air purifier ........7-22 Link System ........7-58 Airbag ..........
Page 485 Alphabetical index Charge warning lamp ......5-54 8-Speed automatic transmission with Brake sports mode........6-39 ABS warning display....... 6-80 Check engine warning lamp..5-53, 6-29 Fluid ........... 11-11 ABS warning lamp......6-80 Child restraint........4-20 Paddle shift ........6-42 Anti-lock brake ....... 6-80 Caution for installing the child restraint on Selector lever operation..
Page 486 Alphabetical index Door ajar warning display ..... 5-7 Combination headlamps and dipper switch... Engine 5-57 Check engine warning lamp..5-53, 6-29 Door courtesy lamps ......7-91 Coolant ....... 10-7, 11-11 Convenient hook......... 7-97 Door coutesy lamps Diesel preheat indicator lamp... 5-51 Coolant (engine) ......
Page 487 Alphabetical index Tank capacity ........2-4 Dipper (High/Low beam change) ..5-59 Forward Collision Mitigation System (FCM) 6-102 Headlamp flasher......5-60 Fuel remaining warning display..5-8, 5-22 Switch ......... 6-107 High-beam indicator lamp ....5-51 Fuses ..........10-22 Lamp monitor buzzer ...... 5-59 Front cooler .........
Page 488 Alphabetical index Indicator and warning lamps ..5-26, 5-50 Meter illumination control .... 5-2, 5-20 Lamp monitor buzzer......5-59 Indicator lamps ....5-26, 5-50, 5-51 Lamps (headlamps, fog lamp, etc.) auto- Microphone....... 7-60, 7-61 cutout function ......... 5-59 Information display ......5-19 Mirror Leakage (Fuel, engine coolant, oil and exhaust Inside rear-view mirror....
Page 489 Alphabetical index Overheating ......... 8-4 Indicator lamp......... 5-51 Switch..........5-64 Rear personal lamps ....7-89, 7-90 Safe driving techniques ......6-3 Bulb capacity........ 10-29 Safety mechanism...... 3-25, 3-26 Parking ..........6-12 Rear turn-signal lamps Parking brake ........6-6 Seat Bulb capacity........ 10-28 Adjustment ........
Page 490 Alphabetical index Tank capacity ........2-4 Side turn-signal lamps Card holder........7-85 Bulb capacity ....... 10-28 Sunglasses holder ....... 7-93 Third seat ..........4-6 Indicator lamp ........ 5-51 Sunroof ..........3-26 Time Setting........7-53 Switch ........... 5-62 Safety mechanism ......3-26 Tools ...........
Page 491 Alphabetical index Tyre chains ........10-19 Switch........5-67, 5-68 Wheel condition ......10-17 Washer fluid level warning lamp ..5-55 Washing ..........9-3 Waxing ..........9-4 Ultrasonic misacceleration Mitigation System Weight ..........11-5 (UMS) ........... 6-109 Wheel Sensor locations ......6-112 Specification.........
Page 493 Certification...
Page 496 REGISTERED No: REGISTERED No: ER34312/14 ER43407/15 DEALER No: DEALER No: 0033578/10 DA36975/14 REGISTERED No: ER34313/14 DEALER No: 0033578/10...

Mitsubishi MOTORS SHOGUN SPORT Owner's Manual

General Information 2

Locking and Unlocking 3

Seat and Seat Belts 4

Section 4

Section 5

Section 6

For Emergencies

Maintenance

Quick Links

Chapters

Need help?

Questions and answers

Related Manuals for Mitsubishi MOTORS SHOGUN SPORT

Summary of Contents for Mitsubishi MOTORS SHOGUN SPORT