Mitsubishi MOTORS PAJERO SPORT Manual

page of 417

/ 417
Contents
Table of Contents
Bookmarks

Table of Contents

Quick Links

Download this manual

Foreword

Thank you for selecting a MITSUBISHI MOTORS product as your

new vehicle.

This owner's manual will add to your understanding and full enjoy-

ment of the many fine features of this vehicle.

It contains information prepared to acquaint you with the proper way

to operate and maintain your vehicle for the utmost in driving pleasure.

MITSUBISHI MOTORS CORPORATION reserves the right to make

changes in design and specifications and/or to make additions to or

improvements in this product without obligation to install them on

products previously manufactured.

It is an absolute requirement for the driver to strictly observe all laws

and regulations concerning vehicles.

This owner's manual has been written in compliance with such laws

and regulations, but some of the contents may become contradictory

with later amendment of the laws and regulations.

If your vehicle is equipped with any locally produced part, the operat-

ing procedure, specifications, maintenance intervals and other contents

found in this owner's manual may not sometimes apply to it.

Please leave this owner's manual in this vehicle at time of resale. The

next owner will appreciate having access to the information contained

in this owner's manual.

Throughout this owner's manual the words WARNING and

CAUTION appear. These serve as reminders to be especially care-

E09200108175

ful. Failure to follow instructions could result in personal injury or

damage to your vehicle.

Indicates a strong possibility of severe personal injury or death if

instructions are not followed.

Means hazards or unsafe practices that could cause minor per-

sonal injury or damage to your vehicle.

You will see another important symbol:

Gives helpful information.

*: Indicates optional equipment.

It may differ according to the sales classification; refer to

the sales catalogue.

Abbreviations used in this owner's manual:

M/T: Manual Transmission

A/T: Automatic Transmission

The symbol used on the vehicles:

: See owner's manual

Table of Contents

Need help?

Do you have a question about the PAJERO SPORT and is the answer not in the manual?

Questions and answers

Summary of Contents for Mitsubishi MOTORS PAJERO SPORT

Page 1 CAUTION appear. These serve as reminders to be especially care- E09200108175 ful. Failure to follow instructions could result in personal injury or Thank you for selecting a MITSUBISHI MOTORS product as your damage to your vehicle. new vehicle. This owner’s manual will add to your understanding and full enjoy- ment of the many fine features of this vehicle.
Page 2 Table of contents Overview/Quick guide General information Locking and unlocking Seat and seat belts Instruments and controls Starting and driving For pleasant driving For emergencies Vehicle care Maintenance Specifications...
Page 3 Instruments and Controls (Driver’s area) Instruments and Controls (Driver’s area) E08500102964 Combination headlamps and dipper switch P.5-79 Turn-signal lever P.5-81 Active Cornering Lights (ACL) P.5-82 Front fog lamp switch P.5-83 Headlamp washer switch* P.5-87 Instruments - Type A* P.5-2 Instruments - Type B* P.5-17 Engine switch P.6-14 Shift paddles P.6-23 Electric remote-controlled outside rear-view...
Page 4 Instruments and Controls Instruments and Controls E08500102977 Front passenger’s airbag indicator P.4-31 8 inch colour LCD meter switches* P.5-21 Smartphone-link Display Audio (SDA)*, Multi Around Monitor operation switch* P.6-113 Steering wheel height and reach Smartphone-link Display Audio (SDA) navigation system* Audio remote control switches adjustment lever P.6-10 Refer to the separate owner’s manual...
Page 5 Interior Interior E08500202398 Front room & map lamps P.7-19, 7-20, 10-22 Seat belts P.4-14 Sunglasses holder P.7-22, 7-23 Adjustable seat belt anchor P.4-16 Hands-free microphone* [for Smartphone-Link Display Audio (SDA), Rear entertainment system* Refer to the separate owner’s manual] Refer to the separate owner’s manual Inside rear-view mirror P.6-11 Supplemental restraint system (SRS)- Sun visors P.7-15...
Page 6 Luggage area Luggage area E08500301611 Tools P.8-6 Jack P.8-6 Luggage hooks P.7-26 Tyre repair kit P.8-7 Luggage floor boxes P.7-22, 7-23 Overview/Quick guide...
Page 7 Exterior - front Exterior - front E08500403456 Wiper and washers P.5-84, 10-14 Bonnet P.10-3 Engine compartment P.10-2, 11-6 Fuel tank filler door P.2-2 Outside rear-view mirrors P.6-12 Adaptive Cruise Control System (ACC) Side-view camera* P.6-113 sensor* P.6-69 Side turn-signal lamps P.5-81, 10-21 Forward Collision Mitigation System (FCM) sensor* P.6-83 Headlamp washer* P.5-87...
Page 8 Exterior - rear Exterior - rear E08500403469 High-mounted stop lamp P.10-21 Rear turn-signal lamps P.5-81, 10-21, 10-23 Glass antenna* P.7-13 Tail lamps P.5-79, 10-21 Blind Spot Warning lamp* P.6-95 Rear wiper and washer P.5-86 Tailgate P.3-17 Rear-view camera* Stop lamps P.10-21 P.6-110, 6-113 Multi Around Monitor* Reversing lamps P.10-21...
Page 9 Quick guide Refer to “Keyless entry system” on page lock/unlock switch, approximately Quick guide 3-3. 150 cm from the tailgate handle. E08500500010 The outside rear-view mirrors can be Driver’s or front passenger’s door lock/unlock Lock and unlock the doors retracted and extended automatically if you switches press the LOCK switch (1) or UNLOCK E08500602116...
Page 10 Quick guide Around the driver’s seat 1-Wiper and washer switch Tailgate switches (Vehicles with electric tailgate) E08500802222 Refer to “keyless operation system” on page 3-6. MIST- Misting function The wipers will operate once. OFF- AUTO- Auto-wiper control Rain sensor The wipers will automatically operate depending on the degree of wetness on the windscreen.
Page 11 Quick guide 2-Steering wheel height and reach 3-Combination headlamps 3-Turn-signal lever adjustment Rotate the switch to turn on the lamps. The turn-signal lamps flash when the lever is 1. Release the lever while holding the steer- operated. ing wheel up. 2.
Page 12 Quick guide 4-Engine switch 5-Electric remote-controlled out- 6-Fuel tank filler door release side rear-view mirrors lever If you are carrying the keyless operation key, you can start the engine. If you press the Open the fuel tank filler door. To adjust the mirror position engine switch without depressing the brake The fuel tank filler is located on the rear left pedal, you can change the operation mode in...
Page 13 Quick guide 7-Electric window control 8-Speed automatic transmission WARNING with sports mode  If the lock button is always pushed to operate the selector lever, the lever may be Press the switch down for opening the win- E08501001514 accidentally shifted into the “P” (PARK) dow, and pull the switch for closing.
Page 14 Quick guide Refer to “8-speed automatic transmission with sports mode” on page 6-20. 4-wheel drive operation E08502000110 Road conditions Driving mode Dry paved road Packed snow Deep snow or Gravel road Sandy road Rocky road and highway road muddy road Super Select 4WD II 2H or 4H 4HLc or 4LLc...
Page 15 Quick guide 4- Forward Collision Mitigation System Multi information display (FCM) and Ultrasonic misacceleration (Type A) 8 inch colour LCD Mitigation System (UMS) OFF indica- meter (Type B) tor display*  P.6-83, 6-90 5- Cruise control indicator display* E08501201587  P.6-63 Always stop the vehicle in a safe place before 6- Adaptive Cruise...
Page 16 Quick guide Type B Type 1 Standard mode 6-Sub unit speedometer  P.5-39 1-Digital clock display (vehicles equipped 12-Brake auto hold standby indicator lamp (white)  P.6-51 with the Smartphone-link Display Audio mark display  P.5-43 (SDA) or Smartphone-link Display Brake auto hold indicator lamp (green) 8-Hill Descent Control indicator lamp* ...
Page 17 Quick guide 15-Driving support display - Cruise control indicator display*  P.6-63 - Adaptive Cruise Control System (ACC) display*  P.6-69 - Blind Spot Warning display*  P.6-95 16-Selector lever position display  P.6-22 17-Odometer  P.5-44 18-Outside temperature display  P.5-43 19-Analog gauge tachometer The tachometer indicates the engine speed (r/min).
Page 18 Quick guide Multi-mode 14-Multi information screen  P.5-35 1-Digital clock display (vehicles equipped 7-Hill Descent Control indicator lamp*  P.6-55 Interrupt display screen  P.5-42 with the Smartphone-link Display Audio (SDA) or Smartphone-link Display 8-Rear differential lock indicator lamp* 15-Selector lever position display ...
Page 19 Quick guide Type 2 Standard mode 1-Digital clock display (vehicles equipped 4-Analog gauge tachometer 10-Drive mode indicator display*  P.6-27 with the Smartphone-link Display Audio The tachometer indicates the engine (SDA) or Smartphone-link Display speed (r/min). The tachometer can help 11-Off Road mode indicator display* ...
Page 20 Quick guide 15-Driving support display - Cruise control indicator display*  P.6-63 - Adaptive Cruise Control System (ACC) display*  P.6-69 - Blind Spot Warning display*  P.6-95 16-Selector lever position display  P.6-22 17-Odometer  P.5-44 18-Outside temperature display  P.5-43 19-Instant fuel consumption indicator Overview/Quick guide 1-18...
Page 21 Quick guide Multi-mode 1-Digital clock display (vehicles equipped 4-Analog gauge tachometer 10-Off Road mode indicator display*  P.6-35 with the Smartphone-link Display Audio The tachometer indicates the engine 11-Sub unit speedometer  P.5-39 (SDA) or Smartphone-link Display speed (r/min). The tachometer can help Audio (SDA) navigation system.
Page 22 Quick guide 16-Driving support display - Cruise control indicator display*  P.6-63 - Adaptive Cruise Control System (ACC) display*  P.6-69 - Blind Spot Warning display*  P.6-95 17-Odometer  P.5-44 18-Outside temperature display  P.5-43 Overview/Quick guide 1-20...
Page 23 Quick guide Type 3 Standard mode 6-Sub unit speedometer  P.5-39 1-Digital clock display (vehicles equipped 12-Analog gauge tachometer with the Smartphone-link Display Audio The tachometer indicates the engine mark display  P.5-43 (SDA) or Smartphone-link Display speed (r/min). The tachometer can help 8-Hill Descent Control indicator lamp* Audio (SDA) navigation system.
Page 24 Quick guide 15-Driving support display - Cruise control indicator display*  P.6-63 - Adaptive Cruise Control System (ACC) display*  P.6-69 - Blind Spot Warning display*  P.6-95 16-Selector lever position display  P.6-22 17-Odometer  P.5-44 18-Outside temperature display  P.5-43 19-Analog gauge speedometer Overview/Quick guide 1-22...
Page 25 Quick guide Multi-mode 1-Digital clock display (vehicles equipped 8-Rear differential lock indicator lamp* 12-Brake auto hold standby indicator lamp  P.6-36 (white)  P.6-51 with the Smartphone-link Display Audio (SDA) or Smartphone-link Display 9-Drive mode indicator display* Brake auto hold indicator lamp (green) ...
Page 26 Quick guide 16-Driving support display - Cruise control indicator display*  P.6-63 - Adaptive Cruise Control System (ACC) display*  P.6-69 - Blind Spot Warning display*  P.6-95 17-Odometer  P.5-44 18-Outside temperature display  P.5-43 19-Analog gauge speedometer Refer to “8 inch colour LCD meter” on page 5-19 Overview/Quick guide 1-24...
Page 28 General information Fuel selection ...................2-2 Filling the fuel tank ................2-2 Installation of accessories ..............2-4 Modification/alterations to the electrical or fuel systems ....2-4 Genuine parts ...................2-5 Safety and disposal information for used engine oil .......2-5 Event Data Recording ..............2-5 MITSUBISHI Remote Control*............2-6...
Page 29 MITSUBISHI MOTORS dealer.  Do not move away from the fuel tank filler  If you continuously use fuel that contains until refueling is finished. If you moved...
Page 30 Filling the fuel tank Refueling NOTE  While filling with fuel, hang the fuel cap on 1. Before filling with fuel, stop the engine. the hook (A) located on the inside of the fuel 2. The fuel tank filler is located on the rear tank filler door.
Page 31 Modification/alterations to documents accompanying this vehicle. only for MITSUBISHI MOTORS but also an the electrical or fuel systems Only MITSUBISHI MOTORS approved authorised MITSUBISHI MOTORS dealer,...
Page 32 Event Data Recording of MITSUBISHI MOTORS GENUINE PARTS. CAUTION E00205900195 At the MITSUBISHI MOTORS dealer you This vehicle is equipped with an event data  Please consult an authorised MITSUBISHI can also get appropriate advice and the recorder (EDR). MOTORS dealer concerning any such fit- assembling of Genuine Parts will be handled ment or modification.
Page 33 MITSUBISHI Remote Control* NOTE MITSUBISHI Remote Con- trol  EDR data are recorded by your vehicle only if a non-trivial crash situation occurs; no data E00206300037 are recorded by the EDR under normal driv- The MITSUBISHI Remote Control allows ing conditions and no personal data (e.g., you to operate the vehicle within the commu- name, gender, age, and crash location) are recorded.
Page 34  People with implantable cardiac pacemak- ® ating the Bluetooth device. ers or implantable cardiovascular-defi- Mitsubishi Motors’ Web site (in English  Display of fuel consumption history brillators should keep away from the only): The fuel consumption information is dis- devices.
Page 35 MITSUBISHI Remote Control* CAUTION NOTE NOTE  The MITSUBISHI Remote Control is • Due to the characteristics of radio waves, ® • The Bluetooth device is in contact with or designed to supplement the keyless operation communication speed tends to decrease as covered by a metal object.
Page 36 MITSUBISHI Remote Control* When the registration is completed, “Suc- 2. Operate the 8 inch colour LCD meter Changing the remote device set- cess” is displayed in the “Status” field on switches select “ ” ting the multi information screen for 5 sec- (REMOTE).
Page 37 MITSUBISHI Remote Control* 2. Operate the 8 inch colour LCD meter switches select “ ” (REMOTE). Then press the Enter switch. 3. Operate the 8 inch colour LCD meter switches to select the “Select”, and press the Enter switch. 4. Operate the 8 inch colour LCD meter switches to select the “Device 1”...
Page 38 Locking and unlocking Keys ....................3-2 Key number tag ................3-2 Electronic immobilizer (Anti-theft starting system) ......3-3 Keyless entry system ...............3-3 Keyless operation system ..............3-6 Doors ....................3-14 Central door locks ................3-15 “Child-protection” rear doors ............3-16 Tailgate ..................3-17 Security alarm system ..............3-29 Electric window control ..............3-32...
Page 39 • Keep away from devices that emit strong 3- Emergency key  If you lose one of them, contact an author- electromagnetic waves, such as cellular ised MITSUBISHI MOTORS dealer as soon phones, wireless devices and high fre- as possible to prevent theft. quency...
Page 40 It is also possible to operate the outside rear- NOTE view mirrors.  If you lose one of them, contact an author- ised MITSUBISHI MOTORS dealer as soon Type 1 Type 2 as possible. To obtain a replacement or extra...
Page 41  If you wish to add key, please contact an lamp switch is in the “” or the “DOOR” • The number of times the turn-signal lamps authorised MITSUBISHI MOTORS dealer. position at this time, the room lamp will come are blinked by the confirmation function...
Page 42 After pressing the “UNLOCK” switch to keep it away from children.  An authorised MITSUBISHI MOTORS unlock the doors and tailgate, if the • If you think batteries might have been “UNLOCK” switch is pressed again twice...
Page 43 Keyless operation system 5. Close the key case firmly. WARNING 6. Install the emergency key removed in step  People with implantable cardiac pacemak- ers or implantable cardiovascular-defi- 7. Check the keyless entry system to see that brillators should not go near the exterior it works.
Page 44 Please consult an authorised passenger’s door lock/unlock switch, the tail- In such cases, use the emergency key. MITSUBISHI MOTORS dealer. gate LOCK switch (when locking) or pull the Refer to “To lock/unlock without using the • You can limit operations to locking and tailgate handle lever (when unlocking), the keyless operation function”...
Page 45 Keyless operation system Operating range for locking and NOTE NOTE unlocking the doors and tailgate  Even if the keyless operation key is within  Even if it is within the operating range, if the the operating range, if the key is near to the keyless operation key is in a small item E00306202060 ground or high up, the system may not oper-...
Page 46 Please consult an If the room lamp switch is in the “” or the authorised MITSUBISHI MOTORS dealer. “DOOR” position at this time, the room lamp  The tailgate handle lever (C) or the tailgate will turn on for 15 seconds.
Page 47 1- Lock  Functions can be modified as stated below. 2- Unlock For further information, please contact an authorised MITSUBISHI MOTORS dealer. • Activating the operation confirmation func- tion (blinking of the turn-signal lamps) only NOTE during locking, or only during unlocking.
Page 48 Keyless operation system Warning activation E00305902608 In order to prevent vehicle theft or the accidental operation of the keyless operation system, the buzzer and the display on the information screen in the instrument cluster are used to alert the driver. If a warning is activated, always check the vehicle and the keyless operation key.
Page 49 For further information, please contact an authorised MITSUBISHI MOTORS dealer. • Even if you have the keyless operation key within the engine start operating range, if the keyless operation key and vehicle ID codes cannot be matched, for example due to the ambient environment or electromagnetic conditions, the warning may be activated.
Page 50 Keyless operation system Item Display Buzzer Note (Solution) Operation Inner buzzer When the operation mode is in any mode other than OFF, if you try to lock the doors and tail- mode OFF sounds once gate by pressing the driver’s or front passenger’s door lock/unlock switch, or the tailgate reminder sys- Outer buzzer LOCK switch, a warning is issued and you cannot lock the doors and tailgate.
Page 51 Doors 2- Unlock Doors NOTE  The driver’s door can be opened without NOTE E00300403706 using the lock knob by pulling on the inside CAUTION  When locking or unlocking with the key, all door handle. doors and the tailgate will be locked or ...
Page 52 Central door locks Central door locks E00300803683 NOTE  Repeated continuous operation between lock and unlock could activate the central door locking systems built-in protection circuit and prevent the system from operating. If this occurs, wait approximately 1 minute before operating the central door lock sys- tem.
Page 53 MITSUBISHI MOTORS authorised MITSUBISHI MOTORS dealer. dealer immediately. • The door does not lock automatically...
Page 54 Tailgate CAUTION WARNING NOTE  When driving with a child in the rear seat,  When there is a build up of snow or ice, it  Gas struts (A) are installed to support the please use the child protection to prevent should be removed before opening the tail- tailgate.
Page 55 Tailgate Refer to “Keyless operation system” on page It is designed to provide a way to open the CAUTION 3-6. tailgate in the case of a discharged battery.  When operating the tailgate handle lever (A), Refer to “Central door locks” on page 3-15. put your fingers to the position shown in the 1.
Page 56 Tailgate WARNING Operating the tailgate (the elec- CAUTION tric tailgate)  Always keep the release lever lid on tail-  Do not install accessories other than MIT- gate closed when driving so that your lug- SUBISHI MOTORS GENUINE parts on the E00314700031 gage cannot accidentally bump the lever electric tailgate.
Page 57 Tailgate CAUTION NOTE NOTE  Do not apply excessive force on the electric  If the electric tailgate operation switch is  If the battery or fuse is replaced while the tailgate when opening or closing it. Doing so pressed or the hands-free access is used electric tailgate is open, it cannot be closed could cause a breakdown.
Page 58 Tailgate <Closing conditions> lamps flash, and the electric tailgate operates  Operating the electric tailgate using as follows: the inside electric tailgate switch  The operation mode is in OFF. E00315000031  The electric tailgate is completely open. ・ While closed: The tailgate completely The electric tailgate can be operated automat- ...
Page 59 Tailgate If the open switch is pressed, the warning  Opening the electric tailgate using buzzer sounds, the hazard warning lamps the open switch flash, and the electric tailgate opens. E00315200033 The electric tailgate can be opened automati- NOTE cally, even if it is locked, by pressing the open switch (A) when the keyless operation key is ...
Page 60 Tailgate ・ While closed: The tailgate completely CAUTION opens.  Turn the automatic operation OFF before ・ While open: The tailgate completely you wash or wax the surrounding area of the closes. kick motion sensor or install/remove a car cover, etc. If the hands-free access remains on, you may be injured due to a sudden oper- NOTE ating of the electric tailgate resulting from a...
Page 61 Tailgate NOTE NOTE  Do not attach or install plated parts or metal  If you perform unlocking operation while the parts, etc., near the kick motion sensor. Oth- close and lock function is operating, all erwise, the kick motion sensor may not react doors and the tailgate are unlocked, and the and the electric tailgate may not operate nor- electric tailgate is closed to its fully closed...
Page 62 Tailgate  Height memory NOTE E00315500036  The stop position of the electric tailgate can The electric tailgate can be set to stop half- not be set to a height less than 1/5 from the way while opening automatically. bottom. [To set] [To reset] 1.
Page 63 Tailgate CAUTION NOTE  Switching automatic operation of the electric tailgate ON/OFF  If the safety mechanism is repeatedly acti-  If snow has accumulated on the electric tail- E00315900030 vated, the tailgate could be switched to man- gate, remove it before operation. When the operation mode is ON, automatic ual operation.
Page 64 Tailgate Refer to “8 inch colour LCD meter After unlocking the electric tailgate, press the 1. Insert the cloth-covered tip of a straight switches” on page 5-21. tailgate open switch (A) and pull up the tail- blade (or minus) screwdriver into the Refer to “Function setting display”...
Page 65 Tailgate WARNING CAUTION CAUTION  Always keep the release lever lid on the  The safety mechanism is deactivated when  Do not touch the latch (A) on the inside of electric tailgate closed when driving so the electric tailgate is closed manually. the electric tailgate.
Page 66 Security alarm system Security alarm system The security alarm has four System armed mode modes: E00301502491 (The buzzer stops and the security indicator The security alarm system is for alerting the lamp continues to blink with the indicator’s surrounding area of suspicious behaviour to reduced lit-up duration time.) System preparation mode prevent unlawful entry into the vehicle by...
Page 67 Security alarm system 1. Put the operation mode in OFF. NOTE Tailgate LOCK switch (except for vehicles 2. Exit the vehicle and close all of the doors equipped with the electric tailgate)  The alarm will resume if unlawful actions and tailgate.
Page 68 Have the vehicle inspected at an authorised Replace the battery at your authorised MITSUBISHI MOTORS dealer.  Pressing the UNLOCK switch on the key. MITSUBISHI MOTORS dealer.  Putting the operation mode in ON.
Page 69 Electric window control NOTE NOTE  The time between pressing of the UNLOCK  When the operation mode is put in ON, the switch on the key, or the driver’s or front buzzer sounds 4 times. This operation indi- passenger’s door lock/unlock switch and cates that the alarm was activated while the automatic locking can be adjusted.
Page 70 Electric window control Driver’s switches Driver’s switch The driver’s switches can be used to operate all door windows. A window can be opened or closed by operating the corresponding switch. Press the switch down to open the window, and pull up the switch to close it. If the switch is fully pressed down/pulled up, the door window automatically opens/closes 1- Driver’s door window...
Page 71 Electric window control Safety mechanism NOTE  The safety mechanism can be activated if the E00302502456 driving conditions or other circumstances When the door window is automatically cause the door windows to be subjected to a closed by pulling up the switch fully, if a physical shock similar to that caused by a hand or head is trapped in the closing win- trapped hand or head.
Page 72 Seat and seat belts Seat arrangement ................4-2 Seat adjustment ................4-4 Front seats ..................4-4 Second seats ..................4-5 Third seats ..................4-6 Head restraints .................4-7 Making a luggage area ..............4-9 Making a flat seat ................4-13 Seat belts ..................4-14 Pregnant women restraint ..............4-19 Seat belt pre-tensioner system and force limiter system ....4-19 Child restraint ................4-20 Seat belt inspection ................4-28 Supplemental restraint system (SRS)-airbag .........4-28...
Page 73 Seat arrangement Seat arrangement E00400202043 By operating the front, second or third seat, select the desired seat arrangement. Seat and seat belts...
Page 74 Seat arrangement Normal usage Flat seat  P.4-13 Folding the second seats  P.4-9 Folding the third seatbacks forward Making a luggage area  P.4-11 Folding the third seats  P.4-12 Seat and seat belts...
Page 75 Seat adjustment Seat adjustment WARNING CAUTION  To minimize the risk of personal injury in  When sliding or reclining the seat rearward, E00400302044 the event of a collision or sudden braking, pay careful attention to the rear seat passen- Adjust the driver’s seat so that you are com- the seatbacks should always be in the gers.
Page 76 Second seats 3- To adjust seat cushion height (driver’s 4- To adjust seat cushion angle CAUTION side only) Operate the switch as indicated by the  The reclining mechanism of the seatback is Turn the dial and adjust the seat cush- arrows and adjust the seat cushion spring loaded, causing it to return to the ver- ion height to the desired position.
Page 77 Third seats To get in and out of the third seat E00402500280 Getting in and out of the third seat can be made easily by folding the second seat. Refer to “Folding the second seats” on page 4-9. NOTE CAUTION ...
Page 78 Head restraints To adjust height Second or third seats To reduce the risk of injury in an accident, Front seat pull up the head restraint to the locked posi- tion. Adjust the head restraint height so that the centre of the head restraint is as close as pos- To raise the head restraint, move it upward.
Page 79 Head restraints WARNING To install Third seats  When a person sits in the second or the third seats, pull up the head restraint to a Confirm that the head restraint is facing the height at which it locks in position. Be correct direction, and then insert it into the sure to make this adjustment before start- seatback while pressing the height adjusting...
Page 80 Making a luggage area CAUTION  When folding or storing the seat, be sure not to catch your hand or leg. NOTE  It is possible to folding the seat indepen- dently on each side. Folding the second seats CAUTION E00403801287 Making a luggage area ...
Page 81 Making a luggage area CAUTION  Do not allow any person to sit on the folded seat, and do not place luggage on it. The seat’s mounting fittings could bend under the weight, making it impossible for the seat to be retained on the vehicle.
Page 82 Making a luggage area 2. Push the seat until you hear a “click” and 4. Pull the seatback lock release band (B), the seat locks securely. then tilt the seatback forward until you Folding the third seatbacks for- hear a “click”. ward E00403601113 To fold...
Page 83 Making a luggage area Push lightly on the seatback to confirm Folding the third seats that it has actually been secured. E00403901129 To fold 1. Fold the second seats. (Refer to “Folding the second seats” on page 4-9.) 2. Lower the head restraints of the third seat to the lowest position.
Page 84 Making a flat seat 3. Lift the seat cushion backward. Fold the stand (C) and then gently lower the seat To return Making a flat seat cushion. E00404302130 1. Fasten the cover to the seatback with the By removing the head restraints and fully band (E).
Page 85 Seat belts 4. Store the front head restraints between the CAUTION front seats.  To ensure the seats are locked securely, The flat seat configuration is now com- attempt to move them back and forth. plete.  Do not jump on, or impact the seatbacks Reverse the above procedures when heavily.
Page 86 Seat belts 2. Insert the latch plate into the buckle until WARNING WARNING a “click” is heard.  Seat belts should always be worn by every  Always adjust the seat belt to a snug fit. adult who drives or rides in this vehicle, ...
Page 87 Seat belts Seat belt reminder NOTE  If the seat belt subsequently remains unfas- E00409802749 tened, the warning lamp and the tone will Warning lamp issue further warnings each time the vehicle starts moving from a stop.  For the front passenger seat, the warning function works only while a person is sitting on the seat.
Page 88 Seat belts WARNING WARNING NOTE  When adjusting the seat belt anchor, set it  Be sure to securely connect the both latch  Pulling out the latch plate by force may dam- at a position that is sufficiently high so plate (A and B).
Page 89 Seat belts 5. Pull the belt slightly to adjust slackness as desired. To unfasten 1. Hold the latch plate and press the button on the buckle. NOTE  As the belt retracts automatically, keep the latch plate held while retracting so that the belt stows slowly.
Page 90 Third seat  If you need to scrap the vehicle, please con- sult an authorised MITSUBISHI MOTORS Pre-tensioner system dealer. It is important to do so because unex- pected activation of the pre-tensioner seat E00405802477 belts could cause injuries.
Page 91 Child restraint Force limiter system WARNING WARNING  When attaching a child restraint system to  Extreme Hazard! E00406001248 the rear seat, prevent the front seatbacks NEVER use a rearward facing child In the event of a collision, each force limiter from touching the child restraint system.
Page 92 Child restraint If the child restraint system can be pulled WARNING forward or to either side easily on the seat  A REARWARD FACING CHILD cushion after the seat belt has been tight- RESTRAINT must NOT be used in the ened, choose another manufacturer’s child front passenger seat if the front passen- restraint system.
Page 93 Child restraint NOTE • Using the lower anchorage in the second seat ONLY if the child restraint has ISOFIX mountings (See page 4-26). • Using the seat belt (See page 4-27). Older children E00406701405 Children who have outgrown the child restraint system should be seated in the rear seat and wear combination lap shoulder belt.
Page 94 Child restraint Suitability for various ISOFIX positions E00411402612 Vehicle ISOFIX positions Mass Group Size class Fixture Second Outboard carrycot ISO/L1 ISO/L2 -Up to 10 kg ISO/R1 -Up to 13 kg ISO/R1 ISO/R2 ISO/R3 -9 to 18 kg ISO/R2 ISO/R3 ISO/F2 ISO/F2X ISO/F3 II &...
Page 95 Child restraint Key of characters to be inserted in the above table:  IUF- Suitable for ISOFIX forward child restraint systems of universal category approved for use in the mass group.  X- ISOFIX position not suitable for ISOFIX child restraint systems in this mass group. Suitability for various seating positions E00406803615 Seating Position...
Page 96 Child restraint Key of characters to be inserted in the above table:  U- Suitable for “universal” category restraints approved for use in this mass group.  X- Seating position not suitable for children in this mass group. Seat and seat belts 4-25...
Page 97 Child restraint Installing a child restraint sys- tem to the lower anchorage (ISOFIX child restraint mount- ings) and tether anchorage E00408902192 Lower anchorage location Your vehicle’s rear seat is fitted with lower A: Child restraint system connectors anchorages for attaching a child restraint sys- CAUTION tem with ISOFIX mountings.
Page 98 Child restraint Installing a child restraint sys- tem to a 3-point type seat belt (with emergency locking mech- anism) E00407102168 Installation: 1. Put a child restraint system on the seat in which you wish to install it, and remove If your child restraint system with a tether the head restraint from the seat.
Page 99 The locking clip must be removed when MITSUBISHI MOTORS dealer. Failure because this affects their characteristics. the child restraint is removed. to have an authorised MITSUBISHI MOTORS dealer perform the work could...
Page 100 Supplemental restraint system (SRS)-airbag The SRS driver’s and front passenger’s air- occupants, including the passengers as well bags are designed to supplement the primary as the driver, must wear their seat belts. protection of the driver and front passenger side seat belt systems by providing those How the supplemental restraint occupants with protection against head and system works...
Page 101 Supplemental restraint system (SRS)-airbag CAUTION  Airbags inflate at an extremely rapid speed. In certain situations, contact with inflating airbags can result in abrasions, bruises, light cuts, and the like. WARNING  IT IS VERY IMPORTANT TO BE PROP- ERLY SEATED. A driver or front passenger too close to the steering wheel or instrument panel WARNING...
Page 102 Supplemental restraint system (SRS)-airbag (Refer to “To turn an airbag off” on page 4-32) Front passenger’s airbag ON-OFF switch is located as shown in the illustration. The indicator normally comes on when the WARNING operation mode is put in ON, and goes off a ...
Page 103 E00407401920 MITSUBISHI MOTORS dealer. airbag ON-OFF switch. Failure to do so The driver’s airbag is located under the pad- could adversely affect the airbag perfor- To turn an airbag off, follow these steps: ded cover in the middle of the steering wheel.
Page 104 Supplemental restraint system (SRS)-airbag moderate to severe frontal impact. The typi- another stationary vehicle, pole or a guard Driver’s knee airbag system cal condition is shown in the illustration. rail). E00412401188 Because frontal collisions can easily move you out of position, it is important to always The driver’s knee airbag is located under the properly wear your seat belts.
Page 105 Supplemental restraint system (SRS)-airbag Examples of some typical conditions are they cannot typically provide protection to Examples of some typical conditions are shown in the illustration. the occupant. shown in the illustration. Such conditions are shown in the illustration. 1- When colliding with a utility pole, tree 1- Collision with elevated...
Page 106 Supplemental restraint system (SRS)-airbag WARNING WARNING  Do not attach anything to the steering  Do not attach accessories to the lower por- wheel’s padded cover, such as badges or tion of the driver’s side instrument panel. accessories. It might strike and injure an Such objects could prevent the driver’s occupant if the airbag inflates.
Page 107 Supplemental restraint system (SRS)-airbag vehicle that is impacted, even with no passen- vehicle body. Examples of some typical con- ger in the front seat or rear seat. ditions are shown in the illustration. The seat belts in your vehicle are your pri- mary means of protection in a collision.
Page 108 Supplemental restraint system (SRS)-airbag Because the side airbags and curtain airbags 5- Vehicle rolls onto its side or roof WARNING do not protect the occupant in all types of col-  Do not allow any rear seat occupant to Because the side airbags and curtain airbags lisions, be sure to always properly wear your hold onto the seatback of either front seat, do not protect the occupant in all types of side...
Page 109 Supplemental restraint system (SRS)-airbag The SRS warning lamp/display is shared by WARNING the SRS airbag and the seat belt pre-tensioner  We recommend work around and on the system. side airbags and curtain airbags system to be done by an authorised MITSUBISHI WARNING MOTORS dealer.
Page 110  If you found any tear, scratch, crack or damage to the portion where the airbag is stored, you should have the SRS inspected by an authorised MITSUBISHI MOTORS dealer. Seat and seat belts 4-39...
Page 112 Instruments and controls Types of instruments ................5-2 Instruments - Type A ...............5-2 Instruments - Type B ..............5-17 Indicator and warning lamps ............5-48 Information screen display list ............5-51 Indicator lamps ................5-74 Warning lamps ................5-75 Information screen display ............5-77 Combination headlamps and dipper switch ........5-79 Turn-signal lever ................5-81 Active Cornering Lights (ACL) .............5-82 Hazard warning flasher switch ............5-83...
Page 113 Types of instruments Types of instruments Instruments - Type A E00569700033 E00500103141 Type A (Refer to page 5-2.) Meter illumination control 1- Tachometer E00531301161 The tachometer indicates the engine Each time you press the rheostat illumination speed (r/min). The tachometer can help Type B (Refer to page 5-17.) button, there is a sound and the brightness of you obtain more economical driving...
Page 114 Instruments - Type A [When the operation mode is OFF] [When the operation mode is ON] NOTE  You can adjust to 8 different levels respec- tively for when the position lamps are illumi- nated and when they are not. ...
Page 115 Instruments - Type A 9-Selector lever position display  P.6-22 Information screen (when the 10-Engine coolant temperature display operation mode is OFF)  P.5-7 E00571800031 11-Odometer  P.5-8 Each time you lightly press the multi infor- 12-Fuel remaining display  P.5-7 mation display switch, the display screen 13-Outside temperature display ...
Page 116 Instruments - Type A 3- Driving range display  P.5-10 Information screen (when the Information screen (when the ECO drive assist display  P.5-12 operation mode is changed from operation mode is ON) 4- Average fuel consumption display  OFF to ON) E00572000030 P.5-10 Each time you lightly press the multi infor-...
Page 117 Instruments - Type A If you press the multi information display NOTE  Redisplay of a warning display switch, the display screen switches to the screen  When there is information to be announced, screen that was displayed before the warning such as a system fault, the buzzer sounds and display and the mark (A) is displayed.
Page 118 Instruments - Type A NOTE Engine coolant temperature dis- play  When the mark is displayed, the warning E00570900048 display screen can be redisplayed on the information screen. Refer to “Information screen (when the oper- ation mode is OFF)” on page 5-4. Refer to “Information screen (when the oper- ation mode is ON)”...
Page 119  On inclines or curves, the display may be between two points. MITSUBISHI MOTORS. “---” is displayed incorrect due to the movement of fuel in the when the inspection time has arrived. tank. Example usage of tripmeter...
Page 120 2. This informs you that a periodic inspec- NOTE tion is due. Please consult an authorised  Depending on the vehicle specifications, the MITSUBISHI MOTORS dealer. displayed time may differ from the next peri- odic inspection time recommended by At that time, when the operation mode is MITSUBISHI MOTORS.
Page 121  If you accidentally reset the display, we rec- approximately 50 km (30 miles), “---” is dis- ommend you to consult an authorised played. E00570600058 MITSUBISHI MOTORS dealer. Refuel as soon as possible. This displays the average fuel consumption from the last reset to the present time. 5-10...
Page 122 Instruments - Type A The reset mode conditions for the average NOTE NOTE fuel consumption display can be switched  The memory of the auto reset mode or man-  The average speed display can be reset sepa- between “Auto reset” and “Manual reset”. ual reset mode for the average fuel consump- rately for the auto reset mode and for the Refer to “Changing the reset mode for aver-...
Page 123 Instruments - Type A momentary fuel consumption is displayed operation mode is set to “ON” to the time with a green bar graph. when it is set to “OFF”. ECO drive level Be conscious of maintaining the momentary fuel consumption above the average fuel con- sumption, driving with the better fuel con- ECO drive level sumption can be possible.
Page 124 Instruments - Type A Refer to “Returning to the factory set- NOTE tings” on page 5-16.  If no operations are made within approxi- mately 30 seconds of the menu screen being NOTE displayed, the display returns to the function ...
Page 125 Instruments - Type A 3. Press and hold the multi information dis- 1. Press and hold the multi information dis- Auto reset mode play switch for about 2 seconds or more to play switch for about 2 seconds or more to switch from A/1 (Auto reset mode) to switch from the setting mode screen to the ...
Page 126 Instruments - Type A Distance Speed NOTE NOTE Fuel con- (driving (average sumption  The temperature value on air conditioning  If “---” is selected in the language setting, a range) speed) panel is switched in conjunction with outside warning message is not displayed when there temperature display unit of the multi infor- is a warning display or interrupt display.
Page 127 Instruments - Type A 1. Press and hold the multi information dis- NOTE NOTE play switch for about 2 seconds or more to  The operation sound setting only deactivates  The drive time is reset when the operation switch from the setting mode screen to the the operation sound of the multi information mode is put in OFF.
Page 128 Instruments - Type B 3. When you press and hold the multi infor- Instruments - Type B mation display switch for about 5 seconds or more, the buzzer sounds and all of the E00500103154 function settings are returned to the fac- tory settings.
Page 129 Instruments - Type B NOTE If the coolant becomes hot, “ ” will blink. NOTE Pay careful attention to the engine coolant  If you press and hold the button for approxi-  It may take several seconds to stabilise the temperature display while you are driving.
Page 130 Instruments - Type B average and instant fuel consumption, aver- age speed, driving support etc. [When the operation mode is OFF] CAUTION 3 types of screen display can be displayed on  Do not drive with an extremely low fuel 8 inch colour LCD meter as shown below.
Page 131 Instruments - Type B Type 1 Type 2 Type 3 Standard mode Standard mode Standard mode Multi-mode Multi-mode Multi-mode 5-20 Instruments and controls...
Page 132 Instruments - Type B 8 inch colour LCD meter switches E00571700056 The 8 inch colour LCD meter switches can change the display type, change vehicle infor- mation and various settings etc. 1- Enter switch 2- Back switch 3- Left switch 4- Up/Down switch 5- Right switch Instruments and controls...
Page 133 Instruments - Type B How to change of display type E00573900036 Type 1 Type 2 Type 3 Standard mode Standard mode Standard mode Multi-mode Multi-mode Multi-mode : Enter/Back switch : Left/Right switch : Changing by function setting display. Refer to “Changing the display type setting” on page 5-39. 5-22 Instruments and controls...
Page 134 Instruments - Type B type setting” on page 5-39.  Changing by the 8 inch colour LCD meter switches NOTE E00574000034 “Standard mode” and “Multi-mode” can be  The screen changes to “Standard mode” at the time of re-ON after the operation mode is changed by using the Enter switch and Back put in OFF.
Page 135 Instruments - Type B Indication in the display E00574200036  Type 1 Standard mode 1-Digital clock display (vehicles equipped 4-Analog gauge speedometer 10-Drive mode indicator display*  P.6-27 with the Smartphone-link Display Audio 5-Digital speedometer 6-Sub unit speedometer  P.5-39 (SDA) or Smartphone-link Display 11-Off Road mode indicator display* ...
Page 136 Instruments - Type B 14-Small information screen  P.5-34 Interrupt display screen  P.5-42 15-Driving support display - Cruise control indicator display*  P.6-63 - Adaptive Cruise Control System (ACC) display*  P.6-69 - Blind Spot Warning display*  P.6-95 16-Selector lever position display ...
Page 137 Instruments - Type B Multi-mode 1-Digital clock display (vehicles equipped 8-Rear differential lock indicator lamp* 15-Selector lever position display  P.6-36  P.6-22 with the Smartphone-link Display Audio 16-Odometer  P.5-44 (SDA) or Smartphone-link Display 9-Drive mode indicator display*  P.6-27 Audio (SDA) navigation system.
Page 138 Instruments - Type B  Type 2 Standard mode 1-Digital clock display (vehicles equipped 4-Analog gauge tachometer 10-Drive mode indicator display*  P.6-27 with the Smartphone-link Display Audio The tachometer indicates the engine (SDA) or Smartphone-link Display speed (r/min). The tachometer can help 11-Off Road mode indicator display* ...
Page 139 Instruments - Type B 15-Driving support display - Cruise control indicator display*  P.6-63 - Adaptive Cruise Control System (ACC) display*  P.6-69 - Blind Spot Warning display*  P.6-95 16-Selector lever position display  P.6-22 17-Odometer  P.5-44 18-Outside temperature display  P.5-43 19-Instant fuel consumption indicator CAUTION ...
Page 140 Instruments - Type B Multi-mode 1-Digital clock display (vehicles equipped 4-Analog gauge tachometer 10-Off Road mode indicator display*  P.6-35 The tachometer indicates the engine with the Smartphone-link Display Audio 11-Sub unit speedometer  P.5-39 (SDA) or Smartphone-link Display speed (r/min). The tachometer can help Audio (SDA) navigation system.
Page 141 Instruments - Type B 16-Driving support display - Cruise control indicator display*  P.6-63 - Adaptive Cruise Control System (ACC) display*  P.6-69 - Blind Spot Warning display*  P.6-95 17-Odometer  P.5-44 18-Outside temperature display  P.5-43 CAUTION  When driving, watch the tachometer to make sure that the engine speed indication does not rise into the red zone (excessive engine r/min).
Page 142 Instruments - Type B  Type 3 Standard mode 6-Sub unit speedometer  P.5-39 1-Digital clock display (vehicles equipped 12-Analog gauge tachometer with the Smartphone-link Display Audio The tachometer indicates the engine mark display  P.5-43 (SDA) or Smartphone-link Display speed (r/min).
Page 143 Instruments - Type B 15-Driving support display - Cruise control indicator display*  P.6-63 - Adaptive Cruise Control System (ACC) display*  P.6-69 - Blind Spot Warning display*  P.6-95 16-Selector lever position display  P.6-22 17-Odometer  P.5-44 18-Outside temperature display  P.5-43 19-Analog gauge speedometer CAUTION ...
Page 144 Instruments - Type B Multi-mode 1-Digital clock display (vehicles equipped 8-Rear differential lock indicator lamp* 12-Brake auto hold standby indicator lamp  P.6-36 (white)  P.6-51 with the Smartphone-link Display Audio (SDA) or Smartphone-link Display 9-Drive mode indicator display* Brake auto hold indicator lamp (green) ...
Page 145 Instruments - Type B switch of the 8 inch colour LCD meter switch of the 8 inch colour LCD meter 16-Driving support display switches. switches. - Cruise control indicator display*  P.6-63 - Adaptive Cruise Control System (ACC) display*  P.6-69 - Blind Spot Warning display* ...
Page 146 Instruments - Type B 6-Function setting display  P.5-38 4-Average fuel consumption display Multi information screen  P.5-46 *:If there is no equipment for navigation E00574400038 ECO drive assist display  P.5-47 information display or audio information 5-Average speed display  P.5-46 display is not displayed.
Page 147 Instruments - Type B When 1 or 2 is displayed, pressing the Enter 1-Average fuel consumption display (Auto  Driving information display reset mode)  P.5-46 switch for 2 seconds or more resets the value. E00577700032 Average speed display  P.5-46 2-Average fuel consumption...
Page 148 Instruments - Type B NOTE NOTE  You can switch whether Navigation informa-  Screen display varies depending on audio tion display is displayed or not displayed usage situation. with Interrupt display.  If the audio source information changes, an Refer to “Changing the pop-up display set- interrupt will be displayed.
Page 149 Instruments - Type B Please follow the procedure below. Refer to “Switching automatic operation : Up/Down switch of the electric tailgate ON/OFF” on page 1. Stop the vehicle in a safe place. Firmly 3-26. 1-When warning has not occurred apply the parking brake and put the selec- Refer to “To operate the nanoe™”...
Page 150 Instruments - Type B  Changing the display type setting  Changing the pop-up display setting NOTE E00578200034 E00578400036  When you remove the battery terminal, the You can change display type to the screen You can set the navigation, audio, call display screen switches to “Standard mode”...
Page 151 Instruments - Type B Refer to “Function setting display” on 2. After selecting “Lan-  Operation sound setting page 5-38. guage” (language setting), press the Enter E00578700039 2. After selecting “Rest switch. You can set the presence or absence of opera- reminder”...
Page 152 Instruments - Type B When fuel consumption is selected When temperature is selected Auto reset mode E00579300032 E00579400033  When the average fuel consumption and NOTE NOTE average speed are being displayed, if you press the Enter switch, the average fuel ...
Page 153 Instruments - Type B  To return to the screen displayed before NOTE NOTE the warning display  The average fuel consumption display and • “Rest reminder”: OFF E00576300031 average speed display can be reset separately • “Turn-signal sound setting”: Sound 1 Even if the cause of the warning display is for the auto reset mode and for the manual •...
Page 154 Instruments - Type B  Redisplay of a warning display NOTE CAUTION screen  Before moving your vehicle, check that the  When the mark is displayed, the warning E00576500033 warning display is OFF display screen can be redisplayed on the When the mark is displayed, if you lightly information screen.
Page 155 Example usage of tripmeter and tripmeter MITSUBISHI MOTORS. “---” is displayed 1. Displays the time until the next periodic when the inspection time has arrived. inspection. It is possible to measure two currently trav- elled distances, from home using tripmeter...
Page 156 OFF. When the display is ommend you to consult an authorised until the next periodic inspection will be MITSUBISHI MOTORS dealer. reset, the time until the next periodic inspec- displayed. tion is displayed and the warning display is...
Page 157 Instruments - Type B “Function setting display” on page 5-38. NOTE Average speed display  The driving range is determined based on the E00572600052 fuel consumption data. This may vary This displays the average speed from the last depending on the driving conditions and hab- reset to the present time.
Page 158 Instruments - Type B NOTE NOTE NOTE  The memory of the auto reset mode or man-  The display setting can be changed to the  The ECO drive assist is displayed only when ual reset mode for the average speed display preferred units {km/L, mpg (US), mpg (UK) vehicle is driving with the selector lever in is erased if the battery is disconnected.
Page 159 Indicator and warning lamps ECO drive level High Indicator and warning lamps E00523701456 Instruments - Type A E00576900037 5-48 Instruments and controls...
Page 160 Indicator and warning lamps 1- Position lamp indicator lamp  P.5-75 18- Anti-lock brake system (ABS) warning lamp  P.6-58 2- Turn-signal indicator lamps/Hazard warning indicator lamps  P.5-74 19- Active Stability & Traction Control (ASTC) indicator lamp P.6-62 3- Front fog lamp indicator lamp ...
Page 161 Indicator and warning lamps Instruments - Type B E00577000035 1- Front fog lamp indicator lamp 8- Supplemental restraint system (SRS) 14- Active Stability & Traction Control  P.5-75 warning lamp  P.4-38 (ASTC) OFF indicator lamp  P.6-62 9- Brake warning lamp (red)  P.5-75 15- 8 inch colour LCD meter ...
Page 162 • An extremely strong electromagnetic wave is received from a source such as an illegal radio set, a spark from a wire, or a radar station. • Abnormal voltage or a static electricity discharge is generated by the operation of installed electrical equipment (including after-market parts). If the warning display appears many times, consult an authorised MITSUBISHI MOTORS dealer. Warning display list...
Page 163 Information screen display list Screen Cause Solution (Reference)  There is a fault in the keyless operation Refer to “Keyless operation system” on page system. 3-6.  You put the operation mode in ON without  Fasten your seat belt properly. Refer to fastening your seat belt.
Page 164 (Instruments - Type A), 5-18 (Instruments - Type B).  There is a fault in the fuel system.  Have your vehicle inspected at an author- ised MITSUBISHI MOTORS dealer.  You are driving with the parking brake still  Release the parking brake. applied.
Page 165 Information screen display list Screen Cause Solution (Reference)  The parking brake cannot be applied tem- Refer to “Electric parking brake” on page 6-4. porarily due to repeated operation of the Electric parking brake switch within a short time.  The accelerator pedal is depressed when Refer to “Electric parking brake”...
Page 166 Then, operate the engine switch.  We recommend you to have the brake auto hold system inspected by an authorised MITSUBISHI MOTORS dealer. Refer to “Brake auto hold” on page 6-50.  The brake auto hold system does not turn ...
Page 167 6-16.  There is a fault in the steering wheel lock.  Immediately stop the vehicle in a safe place and consult an authorised MITSUBISHI MOTORS dealer. Refer to “Steering wheel lock” on page 6-16. 5-56 Instruments and controls...
Page 168 Information screen display list Screen Cause Solution (Reference)  The steering wheel is locked.  Press the engine switch while turning steer- ing wheel. Refer to “Steering wheel lock” on page 6-16.  The engine is stopped while the selector ...
Page 169 “4HLc”  “4LLc”.  There is a fault in the A/T.  Have your vehicle inspected at an Author- ised MITSUBISHI MOTORS dealer as soon as possible. Refer to “Drive mode indicator display and 2WD/4WD operation indicator display” on page 6-30.
Page 170  There is a fault in the rear differential lock  Have your vehicle inspected at an author- system. ised MITSUBISHI MOTORS dealer as soon as possible. Refer to “The rear differential lock indica- tor lamp/display” on page 6-36.
Page 171  There is a fault in the Hill start assist.  Have your vehicle inspected at an Author- ised MITSUBISHI MOTORS dealer. Refer to “Warning lamp/display” on page 6-54.  There is a fault in the active stability &...
Page 172 Information screen display list Screen Cause Solution (Reference)  The Adaptive Cruise Control System  Increase the following distance by depress- (ACC) has detected the approach of the ing the brake pedal or making other decel- vehicles in front. erating control. Refer to “Proximity alarm”...
Page 173 Information screen display list Screen Cause Solution (Reference)  The Adaptive Cruise Control System Refer to “How to use ACC” on page 6-75. (ACC) control is automatically cancelled.  Conditions for the start of control are not met, the Adaptive Cruise Control System (ACC) can not start the control.
Page 174 Mitigation System (FCM) has been 6-85. activated.  There is a fault in the Forward Collision  Have your vehicle inspected at an author- Mitigation System (FCM). ised MITSUBISHI MOTORS dealer. Refer to “FCM braking function” on page 6-85. Instruments and controls 5-63...
Page 175 Information screen display list Screen Cause Solution (Reference)  The Forward Collision Mitigation System Refer to “FCM braking function” on page (FCM) is not available temporarily. 6-85.  Foreign matter such as dirt adheres to the Refer to “To terminate ACC control” on page Adaptive Cruise Control System (ACC) 6-79.
Page 176 Information screen display list Screen Cause Solution (Reference)  When the Forward Collision Mitigation Refer to “Forward Collision Mitigation Sys- System (FCM) is ON, if the rear differen- tem (FCM) and Ultrasonic misacceleration tial lock switch is set to ON, the FCM will Mitigation System (UMS) ON/OFF switch”...
Page 177 6-95.  The Ultrasonic misacceleration Mitigation  Immediately have your vehicle inspected at System (UMS) does not operate normally an authorised MITSUBISHI MOTORS because there are some malfunctions in the dealer. sensor or the system. Refer to “When there is a malfunction in the system or the sensor”...
Page 178 Information screen display list Screen Cause Solution (Reference)  The Ultrasonic misacceleration Mitigation Refer to “Ultrasonic misacceleration Mitiga- System (UMS) is activated. tion System (UMS)” on page 6-90.  When the Ultrasonic misacceleration Miti- Refer to “When the Ultrasonic misacceleration gation System (UMS) is ON, if the drive Mitigation System is not available”...
Page 179 Information screen display list Screen Cause Solution (Reference)  When the Ultrasonic misacceleration Miti- Refer to “When the Ultrasonic misacceleration gation System (UMS) is ON, if the rear dif- Mitigation System is not available” on page 6-95. ferential lock switch is set to ON, the Ultrasonic misacceleration Mitigation Sys- tem (UMS) will be switched to OFF auto- matically.
Page 180  The Blind Spot Warning (BSW) does not  Have your vehicle inspected at an author- operate normally because there are some ised MITSUBISHI MOTORS dealer as malfunctions in the sensor or the system. soon as possible. Refer to “When there is a malfunction in the system or the sensor”...
Page 181 Information screen display list Screen Cause Solution (Reference)  The engine is overheated.  Stop the vehicle in a safe place and take corrective measures. Refer to “Engine overheating” on page 8-3.  More than specified limit water has accu- ...
Page 182 Information screen display list The operation status of each system is displayed on the information screen. Refer to the appropriate page for the system for further details. Screen System operation status Reference  When the drive mode is shifted by operat- Refer to “Super Select 4WD Ⅱ...
Page 183 Information screen display list Screen System operation status Reference  When “ROCK” mode of Off Road mode is Refer to “Control mode” on page 6-34. selected.  When the auto parking brake function is Refer to “Auto parking brake function” on activated.
Page 184 Information screen display list Screen System operation status Reference  When approaching the guidance location, Refer to “Navigation information display” on etc. page 5-36.  When the reversing sensor system detects Refer to “Reversing sensor system: To oper- an obstruction. ate”...
Page 185 Indicator lamps The setting for rest interval can be changed. Screen Solution Stop the vehicle in a safe place, turn off the engine, and take a rest. Use this display as rough guide for taking rests during a long drive. The interval from the start of your trip until this message is displayed can be set.
Page 186 ON. MITSUBISHI MOTORS dealer. Also, if the Electric parking brake warning lamp (yellow) illuminates while the parking Parking brake indicator lamp...
Page 187 CAUTION safe place, and contact your authorised  The vehicle should be brought to a halt in the MITSUBISHI MOTORS dealer. If you inev-  Prolonged driving with this lamp on may following manner when brake performance itably have to park, park the vehicle on level cause further damage to the emission control has deteriorated.
Page 188 Immediately park your vehicle in a safe instrument cluster will illumi- MITSUBISHI MOTORS dealer as soon as place and we recommend you to have it nate when there is a fault in possible.
Page 189 Information screen display If this warning is displayed, press down the If there is a fault with the charging system, CAUTION Electric parking brake switch to release the the warning display is displayed on the infor-  If the brake warning display is displayed and parking brake while depressing the brake mation screen in the instrument cluster.
Page 190 Combination headlamps and dipper switch Rotate the switch to turn on the lamps. CAUTION NOTE  If the warning is displayed while the engine  The sensitivity of the automatic on/off con- is running, immediately park your vehicle in trol can be adjusted. For further information, a safe place and check the engine oil level.
Page 191 For further information, please contact your cluster will also illuminate. E00528902287 authorised MITSUBISHI MOTORS dealer. This function turns on the position and tail lamps for about 30 seconds after the UNLOCK switch on the key is pressed when...
Page 192 • Press the LOCK switch on the key. deactivated. • Turn the combination headlamps and dip- For further information, please contact your authorised MITSUBISHI MOTORS dealer. per switch to the “ ” or “ ” position. • Put the operation mode in ON.
Page 193 3-flash function can be adjusted. For further information, please contact your 1- Turn-signals authorised MITSUBISHI MOTORS dealer. When making a normal turn, use posi-  It is possible to change the tone of a sound- tion (1). The lever will return automati- ing buzzer as the turn-signal lamps flash.
Page 194 Hazard warning flasher switch The hazard warning flashers can always be in the “ON” direction to turn on the front fog CAUTION operated, regardless of the operation mode. lamps. An indicator lamp in the instrument  If the ACL are left illuminated for approxi- cluster will also come on.
Page 195 Wiper and washer switch Wiper operation under these conditions can Wiper and washer switch scratch the windscreen and damage the wip- ers. E00507102837 The windscreen wipers and washer can be operated with the operation mode in ON or ACC. If the blades are frozen to the windscreen or rear window, do not operate the wipers until the ice has melted and the blades are freed, otherwise the wiper motor may be damaged.
Page 196 For further information, please contact your of the rain sensor by turning the knob (B). can be changed to intermittent operation authorised MITSUBISHI MOTORS dealer. (except vehicle-speed sensitive). • When the wipers operate at a constant inter- For further information, please contact your val despite changes in the extent of rain.
Page 197 “MIST” position. MITSUBISHI MOTORS dealer. The wipers operate automatically several times while the washer fluid is being sprayed. On vehicles equipped with the headlamp Rear window wiper and washer...
Page 198 For further information, please contact your operates together with the windscreen The wipers operate automatically authorised MITSUBISHI MOTORS dealer. washer the first time the windscreen washer several times while the washer fluid lever is pulled. is being sprayed.
Page 199 Rear window demister switch  Avoid using the washer continuously for Customizing the automatic rear more than 20 seconds. Do not operate the window demister washer when the fluid reservoir is empty. Otherwise, the motor may burn out.  Periodically check the level of washer Function can be changed as desired, as stated fluid in the reservoir and refill if required.
Page 200 Horn switch NOTE  The factory setting is “Disable automatic rear window demister”. Horn switch E00508001722 Press the steering wheel on or around the “ ”mark. Instruments and controls 5-89...
Page 202 Starting and driving Economical driving ................6-2 Active Stability & Traction Control (ASTC) ........6-60 Driving, alcohol and drugs ..............6-3 Cruise control* ................6-63 Safe driving techniques ..............6-3 Adaptive Cruise Control System (ACC)* ........6-69 Forward Collision Mitigation System (FCM)* ......6-83 Running-in recommendations ............6-4 Electric parking brake ..............6-4 Ultrasonic misacceleration Mitigation System (UMS)* ....6-90 Parking ...................6-10...
Page 203 Serviced tion. In addition, low tyre pressures adversely economy. by an authorised MITSUBISHI MOTORS affect tyre wear and driving stability. dealer. at regular intervals in accordance with the service standards.
Page 204 Driving, alcohol and drugs Cooler or air conditioning Safe driving techniques E00600300446 The use of the air conditioning will increase Driving safety and protection against injury the fuel consumption. cannot be fully ensured. However, we recom- mend that you pay extra attention to the fol- lowing: Driving, alcohol and drugs E00600200070...
Page 205 Running-in recommendations not only because rearward vision will be Shift point Speed limit CAUTION obstructed, but also the luggage may be pro- 3rd gear 50 km/h  On 4WD vehicles, the “4LLc” range gives jected into the passenger compartment under maximum torque for low-speed driving on 4th gear 65 km/h...
Page 206 Electric parking brake switch. waiting for a while, contact an authorised While holding it, the brake is applied. At this MITSUBISHI MOTORS dealer. time, the following warning display appears with a buzzer sound, but you should continue NOTE to pull and hold the Electric parking brake switch.
Page 207  When there is a malfunction in the Electric MITSUBISHI MOTORS dealer. parking brake, release the Electric parking  Before driving, be sure that the parking brake manually. brake is released, the parking brake indicator Refer to “When the Electric parking brake lamp and the Electric parking brake warning cannot be released”...
Page 208 Electric parking brake may not be applied or cluster. released. Immediately contact the nearest MITSUBISHI MOTORS dealer. For details, refer to “Electric parking brake warning lamp (yellow)” on page 5-76. When parking your vehicle while the Elec- tric parking brake warning lamp (yellow) is...
Page 209  After the manual release of the Electric parking brake, have the vehicle inspected the parking brake indicator lamp in the instru- at an authorised MITSUBISHI MOTORS ment cluster goes off. dealer immediately. Indicator lamp...
Page 210 Electric parking brake 5. Remove the bolts (A) (3 locations) secur- CAUTION ing the cap (B) with a hexagon wrench  Do not drive with the Electric parking brake (C). applied. The brake parts may be worn early and the brake may be disabled by overheat. ...
Page 211 Parking 9. After turning the tool approximately 50 to Parking on an uphill slope WARNING 100 times while pushing it, it becomes  Leaving the engine running risks injury or hard to turn it. death from accidentally moving the selec- Turn the front wheels away from the kerb and When the tool in turned to the opposite tor lever or the accumulation of toxic...
Page 212 Inside rear-view mirror 2. Adjust the steering wheel to the desired Type 1 position. 3. Securely lock the steering wheel by pull- ing the lever fully upward. Type 2 WARNING To adjust the mirror position  Do not attempt to adjust the rear-view mirror while driving.
Page 213 Outside rear-view mirrors To reduce the glare WARNING  Your vehicle is equipped with convex type mirrors. Type 1 Please take into consideration, but objects you see in the mirror will look smaller and farther away compared to a normal flat The lever (A) at the bottom of the mirror can mirror.
Page 214 Outside rear-view mirrors 2. Press the switch (B) to the left, right, up or Retracting and extending the mir- CAUTION down to adjust the mirror position. rors using the mirror retractor  It is possible to retract and extend the mirrors 1- Up by hand.
Page 215 Immediately contact your MOTORS dealer. In order to prevent theft, the engine will not authorised MITSUBISHI MOTORS dealer. • Automatically extend when the driver’s start unless a preregistered keyless operation  If the engine switch operation is not smooth door is closed, put the operation mode in key is used.
Page 216 Engine switch NOTE  When the battery in the keyless operation All vehicle’s electrical devices can be oper- key has worn out, or the keyless operation ated. key is out of the vehicle, warning display The indicator lamp on the engine switch illu- will appear.
Page 217 OFF. details, consult authorised 2. One of the other causes could be low bat- MITSUBISHI MOTORS dealer. tery voltage. If this occurs, the keyless entry system, keyless operation function, and steering lock will also not operate. Operation mode OFF reminder...
Page 218 • Open one of the doors or the tailgate when MITSUBISHI MOTORS dealer.  If your vehicle needs to be towed, unlock the all the doors and the tailgate are closed. steering wheel. Refer to “Towing: Emer- •...
Page 219 Starting and stopping the engine Starting and stopping the CAUTION engine  Never attempt to start the engine by pushing or pulling the vehicle. E00620601497  Do not run the engine at high speeds or drive the vehicle at high speeds until the engine Tips for starting has had a chance to warm up.
Page 220 Starting and stopping the engine The engine sounds slightly different from NOTE NOTE usual while the learning process is taking  When starting the engine, the selector lever  If you have to bring the engine to an emer- place. The change in the engine sound does is in a position other than the “P”...
Page 221 Turbocharger operation NOTE Turbocharger operation  Remove the object or additional key from the E00611201211 keyless operation key before inserting the CAUTION key into the key slot. The vehicle may not be able to receive the registered ID code from ...
Page 222 8-Speed automatic transmission with sports mode Selector lever operation WARNING  If the lock button is always pushed to E00603302441 operate the selector lever, the lever may be The transmission has 8 forward gears and accidentally shifted into the “P” (PARK) 1 reverse gear.
Page 223 NOTE Instruments - Type B MITSUBISHI MOTORS dealer. If you need to move the vehicle, shift the  If you would like to move your vehicle when selector lever as follows. the selector lever cannot be moved from the “P”...
Page 224 8-Speed automatic transmission with sports mode “R” REVERSE WARNING Sport mode  To prevent rolling, always keep your foot E00603902724 on the brake pedal when the vehicle is in This position is to back up. Whether the vehicle is stationary or in “N”...
Page 225 8-Speed automatic transmission with sports mode NOTE CAUTION NOTE • Push the selector lever from the “D”  Repeated continuous operation of the selec-  When driving away on a slippery road, push (DRIVE) position into the manual gate (A) tor lever or the shift paddles will continu- the selector lever forward into the “+ (SHIFT and push the selector lever back into the...
Page 226 8-Speed automatic transmission with sports mode NOTE CAUTION Instruments - Type B  The “A” indicator on the selector lever posi- After a while, confirm that the warning tion display will only blink if there is a prob- display is no longer showing. It is safe to lem with the A/T position switch.
Page 227  Use the selector lever in the correct shift your vehicle inspected at an authorised signals the vehicle can be left in gear and held position in accordance with driving condi- MITSUBISHI MOTORS dealer. stationary with the service brake. tions. Never coast downhill backward with the For longer waiting periods with the engine selector lever in the {“D”...
Page 228 MITSUBISHI MOTORS dealer. “P” (PARK) position when next you drive the vehicle, requiring application of a strong force to the selector lever to move from the Super Select 4WD II “P”...
Page 229 Super Select 4WD II* 2WD/4WD operation indicator display Drive mode indica- Drive mode-selector position Driving conditions Except for multi Multi information tor display information screen screen The basic position for Super Select 4WD II. Full-time 4-wheel drive When driving on dry paved or slippery roads.
Page 230 Super Select 4WD II* : Turn the drive mode-selector while holding it down The drive mode-selector should be positioned in accordance with the following operating conditions: : Turn the drive mode-selector To shift from Procedure The drive mode-selector can be operated while the vehicle is either moving or stationary. When the vehicle is not in motion, shift the selector lever to the “N”...
Page 231 Super Select 4WD II* NOTE  When shifting between “2H”, “4H” and “4HLc” in cold weather while the vehicle is in motion, the transfer gear may make some noise. In cold weather, try to shift the gear while the vehicle is stopped. ...
Page 232 Super Select 4WD II* When the operation mode is put in ON, Drive : Blink (Drive mode indicator dis- : Blink (Drive mode indicator dis- mode indicator display and 2WD/4WD oper- play also blinks) play also blinks) ation indicator display shows the shifting : Illuminate : Illuminate condition.
Page 233 Super Select 4WD II* : Illuminate NOTE NOTE : Remain off  When the drive mode-selector is set between  When parking, apply the parking brake “2H”, “4H” and “4HLc”, the front wheel before stopping the engine and make sure Multi information screen and/or centre differential lock displays blink that the front and the rear wheel displays are...
Page 234 It does not indicate a prob- happens, please contact your nearest author- lem. When “2H” or “4H” or “4HLc” is ised MITSUBISHI MOTORS dealer for selected, this lamp goes out and function inspection. again. Refer to “ASTC indicator or ASTC When this warning display appears, shifting OFF indicator”...
Page 235 Off Road mode* Off Road mode E00642500095 The Off Road mode is the function that enhances driving smoothly on the off-road by selecting the most suitable engine, transmission, and brake control according to the road surface conditions when the drive mode position of Super Select 4WD II is in “4HLc” or “4LLc”. Also refer to “Super Select 4WD II”...
Page 236 Off Road mode* 2. Set the drive mode-selector from “2H” or NOTE “4H” to “4HLc” or “4LLc”. At this time,  The Off Road mode is not activated when the the Off Road mode is switched to drive mode is in “2H” or “4H”. If the Off “GRAVEL”...
Page 237 Rear differential lock* Rear differential lock NOTE  If the rear differential lock switch is turned E00606201486 on during driving, the warning display will If one wheel starts to spin freely and the vehi- appear, the buzzer will sound and the rear cle becomes stuck and cannot be freed even differential lock will remain deactivated.
Page 238 Rear differential lock* Except for multi information screen Multi information screen NOTE  The status of the rear differential lock (resulting from depression of the rear differ- ential lock switch) is shown by blinking or steady illumination of the rear differential lock indicator lamp/display.
Page 239 Rear differential lock* Rear differential lock indicator lamp/display The operation state of rear dif- Indicator display ferential lock Indicator lamp Except for multi information Multi information screen screen Rear differential lock deactivated Switching in progress Rear differential lock activated : Blink (Drive mode indicator display also blinks) : Illuminate (steady) : Remain off 6-38...
Page 240 Rear differential lock* NOTE NOTE CAUTION  The indicator lamp/display and drive mode • If the vehicle speed is 12 km/h or higher,  If a problem is detected in the rear differen- indicator display blink while the rear differ- decelerate to a speed of 2.5 km/h or lower.
Page 241 Rear differential lock* Examples of effective use of the When driving on rocky roads rear differential lock When the vehicle is unable to move because E00606401130 one of the wheels is suspended in the air. CAUTION  Use the rear differential lock only as an emergency measure when the vehicle is stuck and cannot be freed with the drive mode-selector in “4LLc”...
Page 242 4-wheel drive operation* WARNING WARNING  If the rear differential lock is used by mis-  If the rear differential lock is used by mis- take when turning a curve or making a take except when making an emergency right or left turn at a crossing or the like: escape on snow or frozen road: It becomes The vehicle is unable to make a turn and difficult to make a steady turn.
Page 243 4-wheel drive operation* However, note that the braking distance is not shorter than that of a rear-wheel drive vehicle. When using 4-wheel drive on rough roads (snow, mud, sand, etc.), it is important to operate the vehicle correctly. WARNING  Control the accelerator pedal, brake pedal, steering wheel, etc. according to the landform and nature of the soil. The driver should accurately grasp the surrounding circumstances and drive carefully according to the respective circumstances.
Page 244 4-wheel drive operation* Even a vehicle without the equipment for Off Road mode and rear differential lock (if so equipped) run each road condition. The vehicle with each equipment set the recommended mode of the list shown below in each road condition, it may help you drive smoothly. Road conditions Driving mode Dry paved road...
Page 245 4-wheel drive operation* Driving on dry paved road and Driving on packed snow roads Driving on unpaved roads highway E00646500022 E00646600023 E00646400021 Set the drive mode-selector to “4H” position, Check the road surface conditions and set the in accordance with the road conditions, and drive mode-selector to “4HLc”...
Page 246 4-wheel drive operation* to get stuck. This may help you drive Check the sandy road condition and set the NOTE smoothly. drive mode-selector to “4HLc” or “4LLc”.  If the vehicle becomes stuck in deep snow or Gradually depress the accelerator pedal to muddy roads, it can often be moved a rock- start the vehicle and drive at a possible con- WARNING...
Page 247  MITSUBISHI MOTORS is not responsible to the operator for any damage or injury caused or liability incurred by the improper NOTE and negligent operation of a vehicle.
Page 248 Frequent crossing of streams can adversely affect the life span of the vehicle; consult an authorised MITSUBISHI MOTORS dealer and take the necessary measures to prepare, inspect, and repair the vehicle.  After crossing a stream, apply the brakes to be sure they are functioning properly.
Page 249 If the brakes still do not function properly, contact an authorised CAUTION E00606802157 MITSUBISHI MOTORS dealer as soon  Always use tyres of the same size, same as possible to have the brakes checked. Tyres and wheels type, and same brand which have no wear ...
Page 250 Braking Only when you cannot receive a towing ser- CAUTION CAUTION vice from a MITSUBISHI MOTORS dealer  Transport the vehicle with the driving wheels  Avoid driving habits that cause heavy brak- or commercial tow truck service, tow your on a carriage (Type C or D) as illustrated.
Page 251 It is important to take advantage of the engine take your vehicle to an authorised braking by shifting to a lower shift position MITSUBISHI MOTORS dealer immedi- while driving on steep downhill roads in ately. Brake auto hold order to prevent the brakes from overheating.
Page 252 Brake auto hold Indicator lamp (white) NOTE How to use brake auto hold  While operating the brake auto hold system, E00696300038 you may hear an operation noise to increase braking force when the system detected the movement of the vehicle. This does not indi- To turn on brake auto hold NOTE cate a malfunction.
Page 253 Brake auto hold NOTE NOTE NOTE  If any of the following occur while the sys-  When the operating conditions of the brake  If the vehicle is stopped on a steep slope, the tem is standby state, the brake auto hold sys- auto hold are met with the brake auto hold warning display may appear on the informa- tem will be turned off automatically and the...
Page 254 Hill start assist NOTE NOTE To turn off brake auto hold  While the vehicle is held stationary with the • The drive mode-selector of Super Select E00696700032 brake auto hold system, the Electric parking 4WD II is set to “4LLc”. Press the brake auto hold switch to turn off brake will be automatically applied under the the brake auto hold.
Page 255 Hill start assist 3. Release the brake pedal and the hill start CAUTION Warning lamp/display assist will maintain the braking force  Do not overly rely on the hill start assist to E00628201763 applied while stopping for approximately prevent backwards movement of the vehicle. If an abnormal condition occurs in the sys- 2 seconds.
Page 256 The Hill Descent Control is the system that NOTE authorised MITSUBISHI MOTORS dealer. assists the steady driving with the constant (Refer to “ASTC warning lamp/display” on  The indicator lamp should illuminate when speed when descending sharp grades where it page 6-63.)
Page 257 Brake assist system In the following cases, the Hill Descent Con- firmly such as in emergency stop situations NOTE trol brake control operates. and provides greater braking force.  The Hill Descent Control indicator lamp blinks on a flat road, but this does not indi- ...
Page 258 Emergency stop signal system NOTE NOTE Driving hints  When the anti-lock brake system warning  [Activating condition for the emergency stop  Always keep a safe distance from the lamp or only the active stability & traction signal system] vehicle in front of you.
Page 259 MITSUBISHI MOTORS dealer for inspec- Avoid hard braking and high-speed driving. tion. ABS warning lamp/display Stop the vehicle in a safe place. • When the operation mode is put in ON, the...
Page 260 Avoid hard braking and high-speed driving. Stop the vehicle in a safe place and contact an authorised MITSUBISHI MOTORS dealer. Starting and driving 6-59...
Page 261 Active Stability & Traction Control (ASTC) Active Stability & Traction CAUTION NOTE Control (ASTC)  Do not install any aftermarket limited slip  On vehicles with the rear differential lock, differential (LSD) on your vehicle. The the ASTC and ABS functions are suspended E00616701859 active stability control function may stop while the rear differential lock is activated.
Page 262 Active Stability & Traction Control (ASTC) easier to extricate. (Brake control of the NOTE active traction control function is still work-  Vehicles with Super Select 4WD II, the ing to prevent wheel spins when ASC OFF active stability control function does not switch “OFF”...
Page 263 Active Stability & Traction Control (ASTC) ASTC indicator or ASTC OFF CAUTION NOTE indicator  If the temperature in the braking system con-  The indicator may turn on when you start tinues to increase due to continuous brake the engine. This means that the battery volt- E00619301898 control on a slippery road surface, the warn- age momentarily dropped when the engine...
Page 264 Cruise control* Warning display Cruise control Multi information screen of Instruments - Type E00609102656 Cruise control is an automatic speed control system that keeps a set speed. It can be acti- vated at approximately 40 km/h or more. CAUTION CAUTION ...
Page 265 Cruise control* Cruise control switches B- “SET -” switch Type 1 Used to reduce the set speed and to set the Type 1 desired speed. C- “RES +” switch Used to increase the set speed and to return to the original set speed. D- “CANCEL”...
Page 266 Cruise control* 2. Accelerate or decelerate to your desired NOTE Type 2 speed, then push down and release the  When you release the “SET -” switch (B), SET - switch (B) when the indicator dis- the vehicle speed will be set. play is illuminated.
Page 267 Cruise control* To slow down your speed in small amounts, SET - switch Type 1 push down the “SET -” switch (B) for less than approximately 1 second and release it. Push down and hold the “SET -” switch (B) Each time you push down the “SET -”...
Page 268 Cruise control* Type 2 Type 2 To temporarily increase or To temporarily decrease the speed To deactivate decrease the speed E00609703079 Depress the brake pedal to decrease the The set speed driving can be deactivated as E00609601566 speed. To return to the previously set speed, follows: push up the “RES +”...
Page 269  When your speed slows to approximately MITSUBISHI MOTORS dealer. 15 km/h or more below the set speed because of a hill, etc. To resume the set speed ...
Page 270 Adaptive Cruise Control System (ACC)* Adaptive Cruise Control WARNING CAUTION System (ACC)  A driver is responsible for driving safely.  In the following situations, the system may Even if the ACC is in use, always grasp become transiently unable to detect a vehicle E00634601472 the surrounding circumstances and pro- in front or triggers its control and alarm...
Page 271 Adaptive Cruise Control System (ACC)* CAUTION CAUTION NOTE  Never use the ACC in any of the following • Avoid application of strong shock loads to  When depressing the brake pedal while auto- situations. Failure to follow this instruction the sensor and never tamper with or remove matic brake is applied, the brake pedal is felt could lead to an accident.
Page 272 Adaptive Cruise Control System (ACC)* Depress the brake pedal as soon as your vehi- screen. The vehicle is slowly accelerated to WARNING cle comes to a stop. resume the set speed and continues running at • When driving on a curve. that speed.
Page 273 Adaptive Cruise Control System (ACC)* CAUTION CAUTION  The ACC may not be able to maintain the set • When driving in curved sections of road speed or the distance to a vehicle in front and including their entrance/outlet or running may not alert the driver, if the system cannot beside a closed lane in a traffic work or detect the front vehicle properly in the fol-...
Page 274 Adaptive Cruise Control System (ACC)* 3- “RES +” switch Cruise control switch Instruments - Type B Used to make ACC operate at the origi- E00634801142 nally set speed and also to increase the set speed. Type 1 4- “CANCEL” switch Used to cancel the control function of ACC or the cruise control.
Page 275 Adaptive Cruise Control System (ACC)* 4-Vehicles in front symbol: Comes on when the radar detects a vehicle ahead. Two types of indication; “Stand by” and “Active” State Display Stand by Active Instruments - Type A Instruments - Type B Instruments - Type A Instruments - Type B Vehicle in front detected 5-Following distance setting symbol:...
Page 276 Adaptive Cruise Control System (ACC)* The display on the information screen of the the ACC initiates the speed control to the set How to use ACC instrument cluster will switch to show infor- speed. E00635001561 mation on the ACC. When the ACC is activated, it is placed in the Type 1 To start up (place in ‘standby ‘standby state’...
Page 277 Adaptive Cruise Control System (ACC)* while a vehicle in front is being detected. In NOTE NOTE this case, the target speed is set to 40 km/h. • When the vehicle is running at a speed • The Hill Descent Control is operating (if so Setting the ACC to any speed outside of this between approximately 10 and 40 km/h and equipped).
Page 278 Adaptive Cruise Control System (ACC)* NOTE By using the “RES +” switch: Type 1  There is some time lag between the setting to The set speed increases by 1 km/h every time a new speed and actually accelerating to that you push up the “RES +”...
Page 279 Adaptive Cruise Control System (ACC)* NOTE NOTE By using the “SET -” switch:  The ACC control at the original set speed  There is some time lag between the setting to The set speed decreases by 1 km/h every time resumes as soon as you release the accelera- a new speed and actually decelerating to that you push down the “SET -”...
Page 280 Adaptive Cruise Control System (ACC)* NOTE NOTE By using the brake pedal:  The ACC control is cancelled if you depress  The set speed indication on the display turns If you depress the brake pedal while the ACC the brake pedal and the ACC control does to “---”...
Page 281 Adaptive Cruise Control System (ACC)* tance setting and running-ahead vehicle sym-  When ABS, ASTC or TCL is in opera- Type 1 bol (only when the ACC is detecting a tion. vehicle) is placed in the standby state of dis- ...
Page 282 “OFF” position and then turned back to the “ON” position, con- tact an authorised MITSUBISHI MOTORS Type 2 dealer. For example: The brake system is overheat- ing due to continuous brake control on long downhill slope.
Page 283 Adaptive Cruise Control System (ACC)* NOTE Type 2 Type 1  If the ACC is in the ‘ON state’ when the operation mode is set to “OFF”, the system is set to the ‘OFF state’ when the operation mode is set to “ON” next time. To resume the control E00638300180 After cancelling the ACC control (i.e.
Page 284 Forward Collision Mitigation System (FCM)* Instrument - Type A Display Forward Collision Mitiga- Following distance set- Instrument - Instrument - tion System (FCM) ting Type A Type B E00635101474 The FCM uses a sensor (A) to determine the Long Instrument - Type B distance to a vehicle in front in the same lane and its speed relative to your vehicle’s speed.
Page 285 Forward Collision Mitigation System (FCM)* WARNING CAUTION  The FCM works to avoid frontal collisions  This function does not work for a vehicle in as much as possible. However, the effect of front which is moving extremely slower than its operation varies depending on situa- your vehicle.
Page 286 Forward Collision Mitigation System (FCM)* FCM brake assist function FCM braking function CAUTION  When applying the brake during the auto- E00635301030 E00635501843 If the system judges that there is a high risk of matic braking condition the pedal will feel If the system judges that there is a risk of your vehicle colliding with a vehicle in front, firm.
Page 287 Forward Collision Mitigation System (FCM)* CAUTION CAUTION CAUTION • When the system is faulty (if the system • When the sensor is not clean, “FCM • When the vehicle in front is offset to the self-detects any fault) the “FCM SERVICE RADAR BLOCKED”...
Page 288 Forward Collision Mitigation System (FCM)* CAUTION CAUTION CAUTION • During a certain time after your vehicle  When the FCM will be in the state which can • When passing through a gate with small turns left or right. operate, indication is released automatically. head or side clearances.
Page 289 • When your vehicle is carried on a truck. off the system and please contact an author- • When making sports driving on a circuit. ised MITSUBISHI MOTORS dealer. • When your vehicle is on a chassis dynamometer or free rollers.
Page 290 Forward Collision Mitigation System (FCM)* OFF” message appears on the screen and the NOTE CAUTION “Forward Collision Mitigation System  When the Forward Collision Mitigation Sys- • The Hill Descent Control is ON (if so (FCM) and Ultrasonic misacceleration Miti- tem (FCM) and Ultrasonic misacceleration equipped).
Page 291 Ultrasonic misacceleration Mitigation System (UMS)* When “NEAR” is selected When “FAR” is selected • This telecommunication device is com- plied with the NBTC standard and When “MIDDLE” is selected NOTE • This telecommunication device has the level of Electro Magnetic Radiation in ...
Page 292 Ultrasonic misacceleration Mitigation System (UMS)* Situation Operation display Buzzer When an obstacle is detected in front of your vehicle with the Intermittent selector lever in the “D” (DRIVE) position or in the sport beeping sound mode, if the accelerator pedal is depressed promptly and too strongly, the engine output is suppressed for up to approxi- mately 5 seconds.
Page 293 Ultrasonic misacceleration Mitigation System (UMS)* WARNING CAUTION CAUTION  If the vehicle is trapped in the railway • The Ultrasonic misacceleration Mitigation • When the rain, snow, water or dirt adheres crossing because the system is activated as System is set to OFF by operating the For- to the sensor.
Page 294 Ultrasonic misacceleration Mitigation System (UMS)* CAUTION CAUTION CAUTION • When the obstacle is not horizontal to the • When leaving from a parallel parking. • When the tyre pressure is not proper. ground or not perpendicular to the vehicle • When there is a ultrasonic near your vehicle •...
Page 295 Ultrasonic misacceleration Mitigation System (UMS)* Sensor locations CAUTION NOTE • When there is a loud noise or a ultrasonic  The sensors do not detect objects located in E00643600282 near your vehicle by horn of other vehicle, the area directly below or near the bumper. If There are the sensors (A) on each of 4 places engine sound of a motorcycle, air brake the height of an object is lower than the...
Page 296 Ultrasonic misacceleration Mitigation Sys- Have the vehicle inspected at an authorised tem (UMS) ON/OFF switch is pressed. MITSUBISHI MOTORS dealer as soon as • The drive mode-selector of Super Select possible. 4WD II is in “4LLc” (if so equipped).
Page 297 Blind Spot Warning (BSW) (with Lane Change Assist)* the Blind Spot Warning lamp in the corre- Detection areas Instrument - Type B sponding outside rear-view mirror will illu- E00644400492 minate. If the turn-signal lever is operated to The BSW uses two sensors (A) located inside the side where the Blind Spot Warning lamp the rear bumper.
Page 298 Blind Spot Warning (BSW) (with Lane Change Assist)* WARNING WARNING • When the heights of the next lane and • When the sensor is extremely hot or cold your lane are different. (while the vehicle is parked for a long period of time under a blazing sun or in •...
Page 299 Blind Spot Warning (BSW) (with Lane Change Assist)* Indicator lamp appeared, the Blind Spot Warning lamp will To operate blink and the system will beep three times to E00652300432 alert the driver. When the operation mode is put in ON and “ON”...
Page 300 Have the vehicle inspected at an author- increase of the sensor temperature. When the • When driving near a curb, pot hole and ised MITSUBISHI MOTORS dealer as soon warning display does not disappear after tramline. as possible.
Page 301 Blind Spot Warning displays in the When the warning display does not disappear instrument cluster will appear, even when after having cleaned the sensor, contact an only one vehicle is approaching from one authorised MITSUBISHI MOTORS dealer. side. Rear Cross Traffic Alert (RCTA) E00652400358 The Rear Cross Traffic Alert (RCTA) is an aid system for backing up.
Page 302 Some of these situations include; RCTA may not function properly. Have the vehicle inspected authorised • When the reversing speed of your vehicle is MITSUBISHI MOTORS dealer. approximately 18 km/h or higher. Starting and driving 6-101...
Page 303 Reversing sensor system* to detect low or thin objects or objects near Reversing sensor system Vehicles without a towbar the rear bumper. Thus, make sure to check the surroundings as you operate the vehicle in a E00615501599 The detection areas are within approximately safe manner.
Page 304 • The stickers or accessories have been and prevent the system from functioning attached to the sensors or surroundings. properly. Have the vehicle inspected at an • The sensors or surroundings are covered authorised MITSUBISHI MOTORS dealer. with ice, snow, or mud. Starting and driving 6-103...
Page 305  The volume of the warning buzzer can be adjusted. Back sensor (vehicles with a towbar) details, consult authorised Vehicle to obstacle Warning dis- MITSUBISHI MOTORS dealer. distance play/sound cycle Approximately 125 Intermittent Changing the detection areas to 100 cm E00615801299...
Page 306 3 seconds or more, and switch, the reversing sensor system will not MITSUBISHI MOTORS dealer. release it. The buzzer sounds twice to indicate operate until the engine has been stopped that the detection area has been changed.
Page 307 Sensor system* CAUTION  The sensor system assists you in determining the approximate distance between the vehi- cle and any objects. It has limitations in terms of detectable areas and objects, and may not properly detect some objects. There- fore, do not place excessive confidence in the sensor system, and operate the vehicle as carefully as you would a vehicle without this system.
Page 308 Sensor system* NOTE CAUTION To operate  The sensors do not detect objects located in • The vehicle tilts significantly. E00648100282 the area directly below or near the bumper. If • The vehicle is driven on a rough road (with To operate the system, the operation mode is the height of an object is lower than the a bumpy, gravel, hilly, or grassy surface).
Page 309 Sensor system* the SDA and the SDA navigation system Front and corner sensor Instruments - Type A Vehicle to obstacle Warning dis- Bird’s eye-view distance play/sound cycle Approximately 60 to Intermittent 40 cm Approximately 40 to Fast intermittent 30 cm Within approxi- Continuous mately 30 cm...
Page 310 MITSUBISHI MOTORS dealer. the “R” (REVERSE) position.  For vehicles equipped with the Multi Around  The detection area will not change if you Monitor, you can change the setting to hide keep the “SONAR”...
Page 311 Please drive just as carefully the vehicle inspected at an authorised as you would if the vehicle did not have MITSUBISHI MOTORS dealer. the rear-view camera.  Be sure to visually confirm safety around Range of view of rear-view camera the vehicle with your own eyes.
Page 312 Rear-view camera* NOTE NOTE  Because the rear-view camera has a special • Do not subject the camera to physical shock lens, the lines on the ground between parking such as striking it strongly or throwing a spaces may not look parallel on the screen. thing.
Page 313 Rear-view camera* B: Objects shown on the screen Errors between the display and the actual road surface  When there is an upward slope behind the vehicle The reference lines for distance and vehicle width are based on a level, flat road surface. The reference lines are displayed closer than In the following cases, errors are produced the actual distance.
Page 314 Multi Around Monitor* Therefore when there is an obstacle on the not use them as a guide to distances to solid downward slope, it appears closer than its objects. actual position. Example: On the screen the point B appears the nearest, then the point C and A in order of distance.
Page 315 B- Front-view camera details, consult authorised doors and/or the tailgate open. It will prevent C- Side-view camera MITSUBISHI MOTORS dealer. the Multi Around Monitor from displaying the appropriate range. WARNING Location of each cameras  Do not install anything which will disturb...
Page 316 Multi Around Monitor* Range of view of the Multi Around Monitor cameras A: Front-view camera A: Side-view camera (Right) A: Side-view camera (Left) A: Rear-view camera Starting and driving 6-115...
Page 317 Multi Around Monitor* Types of views of the Multi Side-view/Front-view mode Around Monitor Views of the passenger’s side of the vehicle and the front of the vehicle are displayed. Two different types of views are displayed on the left side and the right side respectively. Bird’s eye-view/Rear-view mode Views of the surroundings of the vehicle and behind the vehicle are displayed.
Page 318 Multi Around Monitor* NOTE NOTE Operation with the switch • When the light of the sun or the light from a • Do not splash the camera with boiling vehicle’s headlamps shines directly into the water. When the switch (A) is pressed, the bird’s- lens.
Page 319 Monitor is turned OFF. played correctly. Be sure to have it inspected by an authorised MITSUBISHI MOTORS NOTE dealer.  When you place the selector lever in the “R”...
Page 320 Multi Around Monitor* NOTE NOTE 1- Approximately 100 cm from the rear Rear-view mode Errors between the display and edge of the rear bumper the actual road surface E00645600215 2- Approximately 200 cm from the rear Reference lines for the distance and the vehi- edge of the rear bumper E00645900029 cle width and upper surface of the rear...
Page 321 Multi Around Monitor* A: Actual objects A: Actual objects A: Actual objects B: Objects shown on the screen B: Objects shown on the screen B: Objects shown on the screen  When there is an upward slope  When there is a downward slope ...
Page 322 Multi Around Monitor* not use them as a guide to distances to solid objects. Example: On the screen the point B appears the nearest, then the point C and A in order of distance. The point A and B actually are the same distances from the vehicle, and the point C is farther off than the point A and B.
Page 323 Multi Around Monitor* 1. Stop the vehicle in a safe place. CAUTION NOTE  The bird’s-eye view is an simulated view  In the bird’s eye-view mode, since the views CAUTION processed by combining view captured by captured by the four cameras, “Front-view ...
Page 324 3. Press and hold down the switch (A) until Cargo loads NOTE the vehicle icon blinks to enter the selec-  Use a MITSUBISHI MOTORS GENUINE tion mode of the vehicle icon colour in the E00609902957 roof carrier, since the brackets to be used bird’s eye-view.
Page 325 Cargo loads CAUTION  When luggage is loaded onto the vehicle, please make sure to drive slowly and avoid excessive maneuvers such as sudden braking or quick turning. In addition, place the luggage on the carrier so that its weight is distributed evenly with the heaviest items on the bottom.
Page 326 For pleasant driving Important air conditioning operating tips ........7-2 Ventilators ..................7-2 Dual-zone automatic climate control air conditioning ....7-6 Rear cooler ..................7-10 Customising the air conditioning ...........7-11 Air purifier ..................7-12 nanoe™*..................7-12 Glass antenna* ................7-13 Link System ...................7-14 USB input terminal* ...............7-14 HDMI terminal* ................7-15 Sun visors ..................7-15 Vanity mirror ..................7-16...
Page 327 Important air conditioning operating tips  When operating the system, make sure the weather. This is to prevent poor lubrication of Important air conditioning air intake, which is located in front of the the compressor internal parts and to maintain operating tips windscreen, is free of obstructions such as the air conditioning in the best operating con-...
Page 328 Ventilators Rear ventilators Left Right E00775000020 1- Close 1- Close 2- Open 2- Open Front side ventilators Rear ventilators Adjusting the air flow direction E00700202626 Move the knob (A) to adjust the air flow Move the knob (A) to adjust the air flow direction.
Page 329 Ventilators NOTE NOTE  The cool air from the ventilators may appear  Be careful not to spill beverages, etc., into as a mist. the ventilators. This is due to moist air being suddenly Doing so might cause the air conditioning cooled by the air conditioning.
Page 330 Ventilators The mode selection and air flowing from the front ventilators Face position Foot/Face position Foot position Foot/Demister position Demister position NOTE  When using the “ ” or “ ” position, set the outside position to prevent the windows from fogging up. For pleasant driving...
Page 331 Dual-zone automatic climate control air conditioning Dual-zone automatic climate control air conditioning E00773000260 The air conditioning can only be used while the engine is running.  Usage 10- Rear window demister switch 1- Air conditioning switch  P.7-9  P.5-88 •...
Page 332 Dual-zone automatic climate control air conditioning • To control the driver’s side and the pas- 1. Press the demister switch to change to the NOTE senger’s side temperature independently “ ” position. When the demister switch  When demisting quick, set the blower to the ...
Page 333 Dual-zone automatic climate control air conditioning In normal conditions, use the system in the NOTE AUTO mode and follow these procedures:  Never place anything on top of the interior air temperature sensor (B), which will pre- 1. Press the AUTO switch. vent it from functioning properly.
Page 334 Dual-zone automatic climate control air conditioning NOTE NOTE  The temperature value of air conditioning is • When the temperature is set to the lowest switched in conjunction with outside temper- setting (18.0°C) ature display unit of the instrument cluster. Inside air will be recirculated and the air On vehicles equipped with Instruments - conditioning will operate.
Page 335 Rear cooler NOTE  When the engine coolant temperature rises to a certain level, the air selection is automati- cally switched to the recirculation position and the indicator lamp (A) comes on. At this time, the system will not switch to the out- side position even if the air selection switch is pressed.
Page 336 Customising the air conditioning A- ON/OFF switch NOTE B- Blower speed adjustment switch To operate the rear cooler in the  If the rear cooler is activated again after it is rear seat stopped by pressing the “ON/OFF” switch or NOTE after the engine is stopped, the blower speed E00774500028...
Page 337 Air purifier  Enable automatic air conditioning control Customising the air selection NOTE When the AUTO switch is pressed, or the  When the demister switch is pressed, in E00774800021 temperature control switch is set to the order to prevent misting of the windows Functions can be changed as desired, as minimum temperature, the air condition- from fogging up, the air ventilator automati-...
Page 338 Glass antenna* Ionised air generated by a device incorpo- Refer to “8 inch colour LCD meter WARNING rated in the vehicle purifies the air in the switches” on page 5-21.  Do not disassemble or repair the genera- cabin by suppressing bacteria. Refer to “Function setting display”...
Page 339 Link System Link System USB input terminal How to connect a USB memory device E00764501790 E00761902022 The Link System takes overall control of the E00762002004 You can connect your USB memory device or devices connected via the USB input terminal iPod* to play music files stored in the USB 1.
Page 340 HDMI terminal* 3. Connect a HDMI cable to the HDMI ter- How to connect an iPod HDMI terminal minal. E00762102063 4. To remove the HDMI cable, perform the E00771400215 installation steps in reverse. 1. Park your vehicle in a safe place and put You can connect a commercially available the operation mode in OFF.
Page 341 Vanity mirror CAUTION For the third seat  If the lid of vanity mirror with lamp is kept open for prolonged periods of time, the vehi- cle’s battery will be discharged. Accessory socket E00711603294 The accessory socket can be used while the operation mode is in ON or ACC.
Page 342 220 V AC power outlet 220 V AC power outlet WARNING WARNING  Never use the 220 V AC power outlet to  Do not spill a beverage on the 220 V AC E00749300165 charge an electric vehicle or a plug-in power outlet, or do not insert any objects The 220 V AC power outlet is located on the hybrid vehicle.
Page 343 Consult an authorised built-in protection circuit. MITSUBISHI MOTORS dealer when you  If the plug of the electrical appliance was If this occurs, put the operation mode in OFF need measurement of the voltage.
Page 344 USB ports (for charging), stop using it ing) might be damaged. and have the vehicle checked by an author-  Insert the USB connector cable in the USB ised MITSUBISHI MOTORS dealer. Front room & map lamps/Rear port (for charging) firmly. personal lamps...
Page 345 For details, please con- automatically after approxi- door or the tailgate is opened. It sult an authorised MITSUBISHI MOTORS mately 30 minutes. goes off about 15 seconds after dealer. The lamp will illuminate again the all doors and the tailgate are ...
Page 346 Interior lamps Luggage compartment lamp E00712701807 Rear personal lamps LED interior illumination 1- ( (Console box) E00712601457 The lamp illuminates regardless of whether Pressing the lens (A) makes the lamp go on E00776100158 the tailgate is open or closed. and pressing the lens again makes it go off. When the lamps are illuminated with the 2- (•) lamp switch in the “...
Page 347 Storage spaces Storage spaces Glove box E00717602794 E00713103655 To open, press the button (A). CAUTION  Never leave lighters, canned carbonated bev- erage, and spectacles in the cabin when park- ing the vehicle in hot sunshine. The cabin will become extremely hot, so lighters and other flammable items may catch fire and unopened drink cans may rupture.
Page 348 Storage spaces The pocket is also possible to store the small Luggage floor boxes items by partitioning it with the loop fastener E00718701942 (A). To use the box, raise the luggage floor board. A- Tray NOTE  The tray can be stored in the floor console CAUTION box lid by turning it over and installing it.
Page 349 Cup holder The cup holder will automatically come out CAUTION NOTE when pushed in the centre area.  The holder should not be used to store any-  Some bottles may not be fastened tightly When stowing the cup holder, push the centre thing heavier than sunglasses.
Page 350 Bottle holder CAUTION Bottle holder  Do not apply excessive force to the cup E00718201527 holder. Otherwise it could cause a break- WARNING down.  Do not spray water or spill beverages inside the vehicle. If the switches, wires, or NOTE electrical components become wet, they could malfunction or cause a vehicle fire.
Page 351 Assist grip NOTE CAUTION WARNING  Do not hang heavy luggage (more than about  Do not use the assist grips when getting into  Do not put a hanger or any heavy or 4 kg) on the hook. or out of the vehicle. The assist grips could pointed object on the coat hook.
Page 352 Luggage hooks Use the hooks on the floor for securing the Third seatback luggage. Fold the third seatback, pull up the cover (A). CAUTION  Do not pile up the luggage beyond the seat- back height. Also, firmly secure the luggage. Otherwise, serious accidents could result due to hindered rearward view or flying objects during sudden braking.
Page 354 For emergencies If the vehicle breaks down ...............8-2 If the operation mode cannot be changed to OFF ......8-2 Emergency starting ................8-2 Engine overheating ................8-3 Bleeding the fuel system ..............8-5 Removal of water from the fuel filter ..........8-5 Tools, jack and jack handle ..............8-6 Tyre repair kit ..................8-7 How to change a tyre ..............8-14 Towing ...................8-18...
Page 355 If the vehicle breaks down 2. One of the other causes could be low bat- If the vehicle breaks down CAUTION tery voltage. If this occurs, the keyless  Check the other vehicle. It must have a entry system, keyless operation function, E00800101137 12-volt battery.
Page 356 Engine overheating 6. Start the engine in the vehicle which has WARNING the booster battery, let the engine idle a  If electrolyte fluid is not visible, or few minutes, then start the engine in the appears to be frozen, Do Not Attempt vehicle with the discharged battery.
Page 357 [If the cooling fans are not turning] Stop the engine immediately and contact [If steam does not come from the engine an authorised MITSUBISHI MOTORS FULL compartment] dealer for assistance. With the engine still running, raise the bonnet to ventilate the engine compart- ment.
Page 358 Bleeding the fuel system If there is anything wrong with the cool- CAUTION ing system or drive belt, have the problem  Be sure to carefully clean away any spilt fuel corrected at an authorised MITSUBISHI which could ignite and cause a fire. MOTORS dealer.
Page 359 ON. If in doubt, brake cannot be released” on page 6-8.) consult your nearest authorised MITSUBISHI MOTORS dealer. Removing and storing the tools, jack and jack handle CAUTION E00802301537  Do not smoke or have any other open flame 1.
Page 360 Tyre repair kit Tyre repair kit E00804501227 This kit enables emergency repair of a small puncture in the tread area of a tyre that has run over a nail, screw, or similar object. Storage The tyre repair kit is stored beneath the lug- A- Thin handle section (with notch) gage floor board of the luggage compartment.
Page 361 2- Tyre compressor  Do not breathe in the vapours of tyre sealant. 3- Tyre sealant bottle  Be sure to use a MITSUBISHI MOTORS 4- Filler hose GENUINE tyre sealant. 5- Valve remover 6- Valve insert (spare) 7- Speed restriction sticker •...
Page 362 Tyre repair kit 4. Turn on the hazard flashers and set up a 7. Remove the valve insert (F) by turning it NOTE warning triangle, flashing signal lamp, anticlockwise using the valve remover • The tyre has completely slipped over the etc., at an adequate distance from the (E).
Page 363 Tyre repair kit 8. Shake the tyre sealant bottle well. 9. Take the cap (G) off the tyre sealant bottle 10. Press the hose onto the valve (D). Holding (H). Do not remove the seal (I). Screw the the sealant bottle upside-down, squeeze it filler hose (J) onto the bottle (H).
Page 364 Tyre repair kit 11. After injecting the sealant, pull the hose 12. After injecting the sealant, securely fit the Pull out the compressor’s power cord (N), off the valve, remove any residual sealant valve remover (E) into the end of the filler insert the plug on the cord into the acces- from the valve, rim and/or tyre.
Page 365 Tyre repair kit 17. Affix the speed restriction sticker (Q) to CAUTION CAUTION the three-diamond mark on the steering  The supplied compressor is designed only  The surface of the compressor will get hot wheel. for inflation of your vehicle tyres. while the compressor is running.
Page 366 MITSUBISHI MOTORS dealer or another emergency repair procedure is complete. specialist. Otherwise the tyre pressure may CAUTION You must still not exceed a speed of drop before the emergency repair procedure 80 km/h.
Page 367 How to change a tyre NOTE To change a tyre  The manufacturer is not liable for damage E00803202530 1. Loosen the wheel nuts a quarter turn with sustained through re-use of any tyre in which tyre sealant has been used. the wheel nut wrench.
Page 368 How to change a tyre 5. Move the jack handle up and down to NOTE raise the ram until just before the jack  When jacking up the rear of the vehicle, turn contacts the jacking point of the vehicle. the tip of the jack so that the grooved portion Ensure that the jack will properly contact (C) properly meets the designated point.
Page 369 How to change a tyre 8. Turn the wheel nuts clockwise by hand to WARNING initially tighten them.  Do not use a jack except the one that came Tighten the wheel nuts until the flanges of with your vehicle. the wheel nuts touch the wheel and the ...
Page 370 How to change a tyre NOTE  Occasionally when the vehicle is jacked up, the grooved portion of the designated point will not come off. When this happens, rock the vehicle to lower the ram.  If the jack is difficult to remove by hand, insert the jack handle (M) into the bracket (N).
Page 371 If towing is necessary, we recommend you to have done your authorised MITSUBISHI MOTORS dealer or a com- mercial tow truck service. CAUTION In the following cases, transport the vehicle using a tow truck.  After changing the tyre and driving the vehi- cle about 1,000 km, retighten the wheel nuts ...
Page 372 Towing Towing the vehicle by a tow CAUTION Towing with rear wheels off the ground (Type C) truck  If you tow the vehicles with the driving wheels on the ground (Type B) as illustrated, make sure that the towing speed and distance Place the selector lever in the “N”...
Page 373 Towing 2. Keep the engine running. 5. Turn on the hazard warning lamps if If the engine is not running, put the opera- required by law. (Follow the local driving tion mode in ON to unlock the steering laws and regulations.) wheel.
Page 374 • Engine damage caused by water immer- leakage, component seizure, or other serious sion faults. After driving flooded roads, be sure to have an inspection at an authorised MITSUBISHI MOTORS dealer and take the necessary measures or repair. For emergencies 8-21...
Page 375 Operation under adverse driving conditions  Depressing the brake pedal during travel On a wet road CAUTION on snowy or icy roads may cause tyre  The impact on tyres and/or wheels when slippage and skidding. When traction  When driving in rain or on a road with driving on a bumpy or rutted road can dam- between the tyres and the road is reduced many puddles a layer of water may form...
Page 376 Vehicle care Vehicle care precautions ..............9-2 Cleaning the interior of your vehicle ..........9-2 Cleaning the exterior of your vehicle ..........9-3...
Page 377 Vehicle care precautions 2. Dip cloth in fresh water and wring it out Vehicle care precautions Cleaning the interior of your well. Using this cloth, wipe off the deter- vehicle gent thoroughly. E00900102005 In order to maintain the value of your vehicle, E00900201865 NOTE it is necessary to perform regular mainte-...
Page 378 Cleaning the exterior of your vehicle Use a vacuum cleaner and brush to clean NOTE CAUTION the seats. If stained, vinyl and synthetic  Remove dirty patches or oil substances  If your vehicle is equipped with the electric leather should be cleaned with an appro- quickly as they can stain genuine leather.
Page 379 Cleaning the exterior of your vehicle net and other sections where dirt is likely to CAUTION CAUTION remain. • When washing around the door glass, hold • If your vehicle is equipped with the Ultra- the nozzle at a distance of more than 70 cm sonic misacceleration Mitigation System CAUTION and at right angles to the glass surface.
Page 380 Cleaning the exterior of your vehicle Do not wax your vehicle in direct sunlight. 3. Dry the vehicle thoroughly using a cham- CAUTION You should wax after the surfaces have ois leather or a soft cloth.  Do not use a scrubbing brush or other hard cooled.
Page 381 Cleaning the exterior of your vehicle acid (battery electrolyte) which may crack, NOTE stain or discolour them.  To clean the inside of the rear window, If they are in contact, wipe off with soft cloth, always use a soft cloth and wipe the window chamois or the like and an aqueous solution glass along the demister heater element and of neutral detergent then immediately rinse...
Page 382 Maintenance Service precautions ................10-2 Catalytic converter .................10-3 Bonnet ....................10-3 Engine oil ..................10-5 Engine coolant ................10-6 Washer fluid ...................10-7 Brake fluid ..................10-7 Power steering fluid ...............10-8 Battery ....................10-8 Tyres ....................10-10 Wiper blade rubber replacement ..........10-14 General maintenance ..............10-15 Fusible links .................10-16 Fuses ....................10-16 Replacement of lamp bulbs ............10-20...
Page 383 Consult an author-  When checking or servicing the inside of ised MITSUBISHI MOTORS dealer for the engine compartment, make sure the necessary information. engine is switched off and has had a chance to cool down.
Page 384 Catalytic converter Check items of engine compartment are located as shown in the figure below. The catalytic converter is installed in the 1. Engine coolant reservoir NOTE exhaust system. 2. Brake fluid reservoir  Use fuel of the type recommended in “Fuel It is important to keep the engine properly 3.
Page 385 Bonnet 3. Support the bonnet by inserting the sup- port bar in its slot. 2. Raise the bonnet while pressing the safety 2. Slowly lower the bonnet to a position lock. about 20 cm above the closed position, then let it drop. CAUTION 3.
Page 386 Engine oil 3. Wait a few minutes. Engine oil Selection of engine oil 4. Remove the dipstick and wipe it with a clean cloth. E01000404925 5. Reinsert the dipstick as far as it goes. To check and refill engine oil 6.
Page 387 Engine coolant the system checked at an authorised MITSUBISHI MOTORS GENUINE Coolant Engine coolant MITSUBISHI MOTORS dealer as soon as has excellent protection against corrosion and possible. rust formation of all metals including alumin- E01000503684 If the level should drop below the “L” (LOW)
Page 388 If the level is low, replenish the container the brake system. with washer fluid. If this occurs, have the vehicle checked by an authorised MITSUBISHI MOTORS dealer. Maintenance 10-7...
Page 389  Keep the reservoir tank cap closed to prevent tery terminals. Doing so could create the brake fluid from deteriorating except sparks. maintenance. Use “MITSUBISHI MOTORS GENUINE  Clean the filler cap before removing and PSF (Power Steering Fluid)”. close the cap securely after maintenance. 10-8...
Page 390 Battery Check the electrolyte level at least once every WARNING WARNING four weeks, depending on the operating con-  Shield eyes  Keep away from children ditions. If the battery is not used, it will discharge by itself with time. Check it once every four weeks and charge with low current as neces- Always wear protective eye goggles when Keep it out of reach of children.
Page 391 Tyres positive (+) terminal and then the negative WARNING NOTE (−) terminal.  Ventilate when charging or using the bat-  Check to see if the battery is securely tery in an enclosed space. installed and cannot be moved during travel. NOTE Also check each terminal for tightness.
Page 392 Tyres Tyre inflation pressures E01001404762 Up to 5 passengers Up to max. load or trailer towing Tyre size Front Rear Front Rear 2.0 bar 2.2 bar 2.0 bar 2.5 bar 265/60R18 110H (200 kPa) (220 kPa) (200 kPa) (250 kPa) {29 psi} {32 psi} {29 psi}...
Page 393 E01007201556 severe braking. Consult your authorised CAUTION MITSUBISHI MOTORS dealer to determine the cause of irregular tread wear.  Avoid using different size tyres from the one Front listed and the combined use of different types of tyres, as this can affect driving safety.
Page 394 Tyres On 4WD vehicles in which the driving power CAUTION Snow tyres is distributed preferentially to the rear wheels,  If the tyres have arrows (A) indicating the E01002000549 ensure that the tyre chains are fitted on the correct direction of rotation, swap the front The use of snow tyres is recommended for rear.
Page 395 Wiper blade rubber replacement CAUTION  An aluminium wheel can be damaged by a tyre chain while driving. When fitting a tyre chain on an aluminium wheel, take care that any part of the chain and fitting cannot be brought into contact with the wheel. ...
Page 396  If you see a suspicious fuel leak or if you smell fuel, do not operate the vehicle; call 1. Lift the wiper arm off the window glass. your authorised MITSUBISHI MOTORS 2. Pull the wiper blade downward to disen- dealer for assistance.
Page 397 3. While pressing the side of the glove box, In case of a melted fusible link, see your unhook the left and right hooks (B) and authorised MITSUBISHI MOTORS dealer lower the glove box. for inspection and replacement. For the fusible links, please refer to “Passen- ger compartment fuse location table”...
Page 398 Fuses Passenger compartment fuse loca- tion table E01007902404 1- Press the tab. 4. Remove the glove box fastener (C), and 2- Remove the cover. then remove the glove box. Fuse load capacity Sym- Capac- Electrical system E01007701809 The fuse capacity and the name of the electri- Tail lamp (left) 7.5 A cal systems protected by the fuses are indi-...
Page 399 Fuses  Some fuses may not be installed on your Sym- Capac- Behind of the fuse block cover Electrical system vehicle, depending on the vehicle model or specifications. Control unit 7.5 A  The table above shows the main equip- ment corresponding to each fuse.
Page 400 Fuses Electrical sys- Capac- Electrical sys- Capac- Electrical sys- Capac- Symbol Symbol Symbol ities ities ities Headlamp high — Spare fuse 30 A 30 A 10 A DC(AUDIO) beam (right) *: Fusible link Headlamp low UREA SCR 30 A 15 A beam (left) ...
Page 401  Never use a fuse with a capacity larger than your vehicle checked by an authorised that specified or any substitute, such as wire, MITSUBISHI MOTORS dealer. foil, etc.; doing so will cause the circuit wir- ing to heat up and could cause a fire.
Page 402 For repair and replacement, contact an CAUTION When replacing a bulb, wait for it to cool authorised MITSUBISHI MOTORS dealer. sufficiently before touching it. You could  When replacing a bulb, be sure to use a new • Headlamps otherwise be burnt.
Page 403  The following lamps uses LEDs rather than  The following lamps uses LEDs rather than bulbs. For repair and replacement, contact an bulbs. For repair and replacement, contact an authorised MITSUBISHI MOTORS dealer. authorised MITSUBISHI MOTORS dealer. • Tail lamps • LED interior illumination (Console box) •...
Page 404 Replacement of lamp bulbs NOTE  When refitting the clip (B), first insert part (G) of the clip into the hole and then press part (H) into it. 3. Pull out the service lid (A) in the direction 5. Remove the socket and bulb assembly by of the arrow and remove the insertion part turning it anticlockwise.
Page 405 Replacement of lamp bulbs NOTE Left side Right side  When installing the lamp unit, align the notch (F) and pins (G) on the lamp unit with the clip (H) and holes (I) in the body. 3. Remove the bulb by pulling out. Licence plate lamps 7.
Page 406 Replacement of lamp bulbs Left side Right side Maintenance 10-25...
Page 408 Specifications Vehicle labelling ................11-2 Vehicle dimensions ................11-3 Vehicle performance ..............11-4 Engine specifications ..............11-5 Electrical system ................11-5 Tyres and wheels ................11-5 Capacity ..................11-6...
Page 409 Vehicle labelling Vehicle labelling E01100105470 Vehicle Identification Number: (VIN) The vehicle identification number is stamped as shown in the illustration. Engine model/number The engine model and number are stamped on the engine cylinder block as shown in the illustrations. 11-2 Specifications...
Page 410 Vehicle dimensions Vehicle dimensions E01100205383 Front track 1,520 mm Overall width 1,815 mm Front overhang 900 mm Wheel base 2,800 mm Rear overhang 1,125 mm Overall length 4,825 mm Ground clearance (unladen) 218 mm With roof rails 1,805 mm Overall height (unladen) With shark fin antenna 1,835 mm...
Page 411 Vehicle performance Minimum turning radius Body 6.0 m Wheel 5.6 m Vehicle performance E01100304286 Maximum speed 180 km/h 11-4 Specifications...
Page 412 Engine specifications Engine specifications E01100604768 Engine models 4N15 No. of cylinders 4 in line Total displacement 2,442 cc Bore 86.0 mm Stroke 105.1 mm Camshaft Double overhead Mixture preparation Electronic direct injection Maximum output (EEC net) 133 kW/3,500 r/min Maximum torque (EEC net) 430 N•m/2,500 r/min Electrical system E01100804669...
Page 413 Capacity NOTE  The tyres that can be installed on your vehicle are shown on the driver’s door label, refer to “Tyre inflation pressures” on page 10-11. For details, contact an authorised MITSUBISHI MOTORS dealer. Capacity E01101307356 Item Quantity Lubricants...
Page 414 — A/T fluid 12.8 litres MITSUBISHI MOTORS GENUINE ATF-MA1 CAUTION  For the A/T fluid, use only the MITSUBISHI MOTORS GENUINE ATF. Use of a different fluid could damage the transmission. Item Quantity Lubricants MITSUBISHI MOTORS GENUINE NEW MULTI GEAR Transfer oil 1.34 litres...
Page 416 E09300104761 Information for station service Capacity 68 litres Cetane number (EN590) Fuel Recommended fuel 51 or higher Refer to the “General information” section for the fuel selection. Engine oil Refer to the “Maintenance” section for the selection of engine oil. Tyre inflation pressure Refer to the “Maintenance”...

Mitsubishi MOTORS PAJERO SPORT Manual

Quick Links

Need help?

Questions and answers

Related Manuals for Mitsubishi MOTORS PAJERO SPORT

Summary of Contents for Mitsubishi MOTORS PAJERO SPORT

Table of Contents